Add TWT service bit capability support to check whether firmware
supports ack event or not. If firmware doesn't support ack event
then service bit capability will become 0 and whenever TWT
command comes, host will not wait for ack event and sends command
in a legacy way.
This support is mainly added to handle new host and old firmware
combination.
Change-Id: I55d373c2e017130b58a4b332da16f0eda8f34eba
CRs-Fixed: 2987749
Changes to extract AoA phase delta values from WMI event.
The AoA phase delta values along with ibf calibration value
is shared to derive the phase values which is to be used in
CFR.
Change-Id: I70f50656db4194025a0b6b37c8b4a27048968e0f
Check the below service bits and set in psoc if the service is supported
by FW.
WMI_SERVICE_RTT_AP_INITIATOR_STAGGERED_MODE_SUPPORTED
WMI_SERVICE_RTT_AP_INITIATOR_BURSTED_MODE_SUPPORTED
Change-Id: I13504958bf31b2d645d915b4db20719bdc9a4133
CRs-Fixed: 2969195
Add WMI support for EHT puncturing by filling puncture
bitmap in vdev start and peer assoc commands.
Change-Id: If1d2541655558f22a96a741999ec4ff7348f695a
CRs-Fixed: 2982498
Add APIs to extract AWGN information from the DCS WMI
interference event received from FW.
Change-Id: I4b2f9f4ef012553dac2a405dc7ac12aef9452354
CRs-Fixed: 2958675
First Requirement:
In case of WTC_BTM roam trigger reason, if FW reports rssi
threshold for 5G and 6G AP via wmi_roam_trigger_reason,
Host should print it in kmsg.
If wtc_candi_rssi_ext_present is set (1), It means fw
reports 5g and 6g candidate rssi (new firmware case).
If wtc_candi_rssi_ext_present is clear (0), It means fw
doesn’t report 5g and 6g candidate rssi (old firmware case).
Host use flag "wtc_candi_rssi_ext_present" to keep backward
compatibility.
Second requirement:
As per user space, value for scan mode in WTC command, is
like below:
0: no Scan, 1: partial scan and 2: full scan.
For NO scan case, FW sends value
ROAM_TRIGGER_SCAN_MODE_NO_SCAN_DISCONNECTION (3)
in wmi_roam_trigger_reason-> wtc_scan_mode. When driver receives
WTC scan mode as ROAM_TRIGGER_SCAN_MODE_NO_SCAN_DISCONNECTION,
it should print value as 0 instead of 3.
Convert WTC scan mode comes from FW to
wmi_configure_roam_trigger_parameters->scan_mode to make it
compatible to WTC command.
Change-Id: I8266460aac1272d345e4349c2ca52b4f9a745d4c
CRs-Fixed: 2965362
Add functions to parse and extract wmi smart monitor
event received from target.
Change-Id: Ic18e3134b684c5f8e12839e997d628909a7e27c9
CRs-Fixed: 2969247
Currently the 6G edge channel feature is MCC specific.
Make the 6G edge channel feature common for WIN and MCC.
Change-Id: I723b6db1d74dca5a911eede4ec6e6167f6b3e6bc
CRs-Fixed: 2976871
New TLVs for MLO flags are introduced in peer assoc WMI
command. Add WMI changes to add these TLV in the peer assoc
command.
Change-Id: I366a96c973c3bedda03e4c370099ff809e0bd83d
CRs-Fixed: 2958851
New TLVs for MLO flags are introduced in peer create WMI
command. Add WMI changes to add these TLV in the peer create
command.
Change-Id: I38a129b30b366b6e3939231699f210d1bac362a1
CRs-Fixed: 2958849
Add parameter 'bool sync' for wlan_cfg80211_crypto_add_key()
to indicate whether or not to add key synchronously.
If it's set to true, wait until install key complete event
is received.
Change-Id: I9a69d486665fb3f65a5720ccfbfb638c09329418
CRs-Fixed: 2865832
New TLVs for MLO flags and partner link info are introduced in vdev
start WMI command. Add WMI changes to add these TLV in the vdev start
command.
Change-Id: Ic7d54c406f69346a6eedb43b1ebcf7266c448bd8
CRs-Fixed: 2958843
WMI vdev create is changed to incude mlo macdress as one of TLV.
Add changes in WMI vdev create send API to include this new TLV.
Change-Id: Ia13bdb8fbfc9f68d1e4c0209201f9acc4f575387
CRs-Fixed: 2958839
802.11BE D1.0 9.4.2.295c.4 Supported EHT-MCS And NSS Set
field specifies maximum 4 optional EHT MCS map, which are
20 MHz-Only STA, BW <= 80 MHz except 20 MHz-Only STA,
BW = 160MHz and BW = 320 MHz.
Therefore set WMI_HOST_MAX_EHT_RATE_SET to 4.
Also add a debug message to log peer_flags_ext.
Change-Id: I3d56998bf0de381ef147d6c0551dcdb7fd935f60
CRs-Fixed: 2963536
Set the SAE EAPOL offload support in resource config based on
WMI_SERVICE_SAE_EAPOL_OFFLOAD_SUPPORT bit received in service
bitmap from Firmware.
Change-Id: I878736105c070df514dfe8d989541227b3baad11
CRs-Fixed: 2957082
Firmware generates wmi Rx diag events every few milliseconds,
and processing the same in system shared work queue may lead to
work queue lock-up detection. Hence, move Rx diag event processing
to dedicated work queue.
Change-Id: I10cdde317794e35bc6d10677ab76ea24a66e1880
CRs-Fixed: 2941409
When obss scan is enabled, FW will trigger scan periodically by
a timer. If a scan was triggered, FW need to access host memory
for data transfer. Occasionally, suspend may happen during one
scan, then FW is unable to access host memory and fw will crash.
So disable the obss scan before suspend.
Change-Id: Ie507da929a3701473cb57888e96e702e34d4c95a
CRs-Fixed: 2927239
Fill peer assoc mlo params in peer assoc request command.
Also add definitions to the WMI_SERVICE_11BE.
Change-Id: Ied7959e022ee27f3bd698b84dc801491175f85b3
CRs-Fixed: 2934417
In WMI_HOST_TP_SCALE, add an option to support 6% transmit power scale
configuration.
Change-Id: I11a67f0efd13ba2c7f2d8d546643a1af37f33613
CRs-Fixed: 2936987
Add new reason code WMI_HOST_ADD_TWT_STATUS_SCAN_IN_PROGRESS
to handle add dialog rejection due to scan is in progress
at firmware.
Change-Id: I30c3d1096690bd0cb7a669206f087e006c23ea44
CRs-Fixed: 2923289
Extract the 11BE flags advertised by FW in WMI_SERVICE_READY_EXT2_EVENTID
and update the regulatory pdev wireless modes. The wireless mode is
currently represented as 'uint32_t' and all the 32 bits are exhausted.
To accommodate the new 11BE flags, change the data type of wireless_modes
from 'uint32_t' to 'uint64_t'.
Add a regulatory phymode 'REG_PHYMODE_11BE' in enum reg_phymode.
If the chip does not support 11BE phymode, FW advertises it via
WMI_REGULATORY_PHYBITMAP enum with a value of REGULATORY_PHYMODE_NO11BE.
Extract the phybitmap and store it in the regualtory
as 'REGULATORY_PHYMODE_NO11BE' bitmap.
CRs-Fixed: 2901260
Change-Id: I4ed3fc7c907b1f76e59efb347c747acea2a163b0
The firmware sends new reason codes due to roaming in
progress and channel switch. Add new reason code for
TWT session.
Change-Id: I3820ac74910e382f5a029de85f8e0915220bb996
CRs-Fixed: 2908384
Updated the EHT related variables as per latest fw cmn headers.
Address review comments from previous EHT gerrits.
Change-Id: I67cd58a4efcf3e06d2ca3b5570432593b1d80825
CRs-Fixed: 2902607
Add 320Mhz band width support and EHT capabilities information in
WMI peer assoc command.
Change-Id: Ie4ee95fb1790c828275e90b384b2bdc04efb3f29
CRs-Fixed: 2882054
EHT capapilities will be received as part of ext2 service ready message.
Update the structure as per firmware common header file and extract the
EHT capabilities field.
Change-Id: Id2dd170db4de588008742f95493d4d06a6431f1c
CRs-Fixed: 2857802
Add support to read the WMI service bit describing support
for the DCS AWGN interference detection mechanism.
CRs-Fixed: 2906768
Change-Id: Id062b9d63a09f522ac1efdbaf6731665fa438630
Add support for storing AWGN interference information for
dynamic channel selection
CRs-Fixed: 2903860
Change-Id: I5d0b6cc0a55303cfb27a02b99aba066557ad9c7d
Add new TWT teardown status code to indicate firmware teared
down the TWT session due to concurrent connection established.
Change-Id: I9b0fb5c5179355f34bd07e91a996da3ade1c9ce8
CRs-Fixed: 2899575
Enable lower 6G edge channel ch2 (5935MHz) for APL2 6G regdmn
using a service bit WMI_SERVICE_ENABLE_LOWER_6G_EDGE_CH_SUPP,
which is not enabled by default.
Also, disable upper 6G edge channel (7115MHz) using another
service bit WMI_SERVICE_DISABLE_UPPER_6G_EDGE_CH_SUPP, that
is enabled by default.
Change-Id: Ia7cb7f7d3165375178adbe70adb19b8671496b6d
CRs-Fixed: 2885623
In order to support different power levels of 6G AP and client,
the channel list event from FW namely "REG_CHAN_LIST_CC_EVENTID"
is modified to add few parameters specific to 6GHZ devices.
Hence the existing event is replaced by REG_CHAN_LIST_CC_EVENT_EXT for
all 2G/5G/6G pdevs in FW. Therefore, after the service ready event, FW
sends the channel list for the configured country/regdomain via
REG_CHAN_LIST_CC_EVENT_EXT. This mandates that all host software need
to have the processing capability of REG_CHAN_LIST_CC_EVENT_EXT to bring
up the AP.
As there can be host software which has not yet implemented the
version of "REG_CHAN_LIST_CC_EVENT_EXT", backward compatibility is lost
if "ONLY REG_CHAN_LIST_CC_EVENT_EXT" is sent by FW.
Hence a 3 way handshake between host and FW is established.
1. FW advertises its capability of processing REG_CHAN_LIST_CC_EVENT_EXT
id via wmi service bit 'wmi_service_reg_cc_ext_event_support'.
2. If the host is capable of processing the "REG_CHAN_LIST_CC_EVENT_EXT"
event id (which is done based on registration of this event), host
sends the capability in WMI_INIT_CMDID setting a bit in host_service_flags.
3. Based on host capability advertised in WMI_INIT_CMDID, FW decides to
send the old event ("REG_CHAN_LIST_CC_EVENTID") or the new event
("REG_CHAN_LIST_CC_EVENT_EXT").
4. If there is no flag indicated by host to FW in WMI_INIT_CMDID, FW
by default sends the old event ("REG_CHAN_LIST_CC_EVENTID").
CRs-Fixed: 2876360
Change-Id: Ibe95f414ad9fff0e5641bcc6e60450ef9afe245b
