Add pld_get_mhi_state API to get current MHI state and
pld_is_pci_ep_awake to indicate that PCI EP is out of
low power state.
Also enable pld_prevent_l1 and pld_allow_l1 API for WCN6750
to manage low power state of PCI EP from Host.
Change-Id: Ic574bf7d7886b8e59b98e65806b387eef3a54e94
For reassociate case, when disconnect is triggered by
wlan_hdd_try_disconnect, then disconnect event is not
indicated to kernel in disconnect handler -
hdd_dis_connect_handler. And if the csr_roam_connect
get failure for some reason, the kernel will only get
error code from driver connect request interface and
the connected bss information in kernel will not get
cleared. Then kernel / driver will be out of sync.
To fix that, for such csr_roam_connect failure case,
let driver return successful status code from driver
connect interface and indicate connection result failure
event to kernel to clear kernel bss information.
Change-Id: I5367262751e63c04553deeb7607cbe13c70f8e15
CRs-Fixed: 2940994
Currently idle shutdown is flushed after the suspend dsc op
start. This can lead to the deadlock when the idle shutdown
work is running as it waits for the dsc ops to complete.
To mitigate this issue, flush the idle shutdown work before
starting the dsc ops in suspend sequence.
CRs-Fixed: 2941314
Change-Id: I023b9eb3543d83a30e0587cec3977e08ac7ab752
When obss scan is enabled, FW will trigger scan periodically by
a timer. If a scan was triggered, FW need to access host memory
for data transfer. Occasionally, suspend may happen during one
scan, then FW is unable to access host memory and fw will crash.
So disable the obss scan before suspend.
Change-Id: I131258b3c975cc7fcf3931f4b1fc1e1a649383ef
CRs-Fixed: 2904237
At present LTE unsafe channel switch and DCS is using
hdd_switch_sap_channel to switch channel of SAP.
hdd_switch_sap_channel has no bw setting parameters and just
use the original bw of SAP - ch_width_orig. The ch_width_orig
(80Mhz) may not be applicable if SAP is channel switching from
5G 80Mhz to 2G. Use the new API wlan_get_ap_prefer_conc_ch_params
to override the bw to appropriate value for the new channel.
Change-Id: I9ab6c92a0534517c524bd56b0c3087d7f75f6368
CRs-Fixed: 2939654
Reset the value of static variable rssi_comb to zero when
last mpdu of ppdu is received in packet capture mode.
Change-Id: Ida76dfb9c98a8e2718844f890e0303802db5bbed
CRs-Fixed: 2940871
Currently, TSO frames are not handled in packet capture mode.
Add support to handle TSO frames.
Change-Id: Ib901defcd369b01a33c87ca888ad80fe5fd086c7
CRs-Fixed: 2932138
The WMI_PDEV_UPDATE_PMK_CACHE_CMDID command is sent even if the
delete/set pmksa command fails due to same entry with same pmk
already exists. This can cause invalid pmk
entries to be updated in the Fw pmk table and also the host/fw
pmksa table goes out of sync.
To avoid this, send the WMI_PDEV_UPDATE_PMK_CACHE_CMDID command
only if set pmksa/del pmksa is successful at crypto
Change-Id: I080ebd9f6ca11bac216e6e8c62ef6060f0adef67
CRs-Fixed: 2937175
Avoid obj mgr logging of get ref API print on console
for MCC as it leads to excessive logging and assert.
Change-Id: I75fb9381a7c122f4d7701888da35c7e38836250e
CRs-Fixed: 2941196
In 6G 160Mhz case, beamforming values are not being sent correctly
because the HE capability is populated from the minimum between bands.
Since FW is advertising the 2G capabilities as a lower value, these are
taking effect. Update these values from the correct band.
Change-Id: I0a0bc14860487f104e7b872894f1eb939c06a613
CRs-fixed: 2939702
Currently if the userspace doesn't send the NSS/BW values, then
the filter_set_valid_mask flag is not set in the
WMI_CFR_CAPTURE_FILTER_CMDID command. So the target doesn't
configure the BW and NSS filter in HW leading to frames getting
filtered out.
Fill default CFR capture NSS and BW values during start
capture.
Change-Id: I46004aa38c09dec8995fff84a3e699581675221b
CRs-Fixed: 2932529
Register for management control frames with the mgmt txrx
component in packet capture mode.
Change-Id: Ibaa20e00753cdeb6a15a79bd458166b47652cdb5
CRs-Fixed: 2932144
Add gConfigBleScanCoexPolicy which can be used to
control performance of ble scan case.
’0’ to place more emphasis on BLE Scan results
‘1’ to place more emphasis on WLAN performance
Change-Id: I46c735d8695523d14f6372bc5e47d1d1f51589ae
CRs-Fixed: 2935051
As part of 11BE 320MHz bandwidth support, add 320MHz support for
SAP module, including 320MHz ACS support.
Change-Id: If26d9e62b16bbecbb1ea10c70f42e9a8464a70c7
CRs-Fixed: 2935873
As part of 320MHz bandwidth support for 11BE, define an API
to get max supported EHT bandwidth in SME, which in turn gets
max BW from WMA layer.
Change-Id: Ifae397ec38cd89758215a9d09fe58a4d7afd22f4
CRs-Fixed: 2935861
New checks have been added in userspace to verify the 6GHz HE
capabilities before allowing the connection. These capabilities
are not currently being shared by host. Add logic to send the
6GHz HE capabilities to userspace.
Also, add APIs to get capabilities from MLME component.
Change-Id: I3d2bbe0d87be6094b6fc74ce01d0e418873cbc6f
CRs-fixed: 2931130
In roam sync handling, pmksa memory is freed right after
set pmka entry is updated in crypto priv params instead
allocate separate buffer for crypto.
Change-Id: I337efcb29d2233b016f93cae7f4f23d3203786a6
CRs-Fixed: 2931162
Enable the history support to log Tx descriptors programmed
in Tx and completion HW rings.
Change-Id: I5ce308354714da78baa05500bc73e1a9ec91b958
CRs-Fixed: 2935363
Opportunistic timer gets triggered as soon as a DBS use case
is completed and hw_mode would be set to SMM when the
timer(5 seconds) expires.
Below is an example scenario,
1. DBS is enabled to support STA on 5GHz + SAP on 2.4GHz on
a Helium device.
2. SAP is disabled(to enable NAN as NAN+SAP is not supported on
HL platforms)
3. Opportunistic timer gets triggered with a timeout of 5 seconds
as DBS is not needed anymore.
4. Once the timer expires, WMI_PDEV_SET_HW_MODE_CMDID command
would be sent to firmware to set the hw_mode to SMM.
But if framework enables NAN immediately after disabling SAP,
firmware can't allow it as NAN is not supported in DBS mode in
Helium platforms. Thereby firmware either rejects the NAN enable
or defer it till set_hw_mode command is received(which introduces
a delay of 5 seconds as host sends it after timer expiry).
So, stop the timer and complete corresponding action when a NAN
command is received from framework to avoid this failure/delay.
Change-Id: I50521c0dd5f2314034957a0f65898c737cfe7e2e
CRs-Fixed: 2937407
HIF PM link state is used to indicate bus is alive or not. This
indicates RING HP/TP updating directly or using async method.In
RTPM suspend failure flow, CLD reject RTPM suspent request, but
state is not resumed correctly.
Change-Id: I3b96dc1fb34e2810d721e1fcb4db609a3d1d684d
CRs-Fixed: 2919930
