Add changes to support get congestion stats(arp stats) from
within cp_stats component.
Change-Id: Ic3b2f020c0169c9113c1b40738f782cbb3b8f6c5
CRs-Fixed: 2222781
Remove duplicate structs wmi_dual_mac_config and sir_dual_mac_config
and use policy_mgr_dual_mac_config.
Change-Id: I6da6539f519ec46ee274ba3f3ae042e5fd9c25d2
CRs-Fixed: 2191031
Number of AP TWT and AP TWT stations are added in
target_resource_config to provide the configuration for TWT.
Add support in WMI to provide appropriate defaults for TWT.
Change-Id: Ica91f981d59a015b0b4cda41ba951b6ba22e8120
CRs-Fixed: 2212667
Add get channel width from phy mode API which will be used by
ndp schedule update event.
Change-Id: I13d00c0b818eb0da434c8a5372b2ab7b6693f22a
CRs-Fixed: 2216801
When SWBA event is enabled, the FW will sent an event to the
host on every TBTT beacon.
Note that, unlike the legacy offload chips, this event is not
used by the host to send out the beacon frame itself.
Change-Id: Icf4440d79f7dbfb544f9d98c4de0e84bdb150459
CRs-Fixed: 2200805
Add ini "min_delay_btw_scans" to set minimum duration allowed between
two consecutive roam scans. Fw should not allow roam scan if duration
between two consecutive roam scan is less than min_delay_btw_scan.
Add ini "roam_trigger_reason_bitmask" to set default value of
bit-mask containing roam_trigger_reasons for which
min_delay_btw_scans constraints should be apply.
Pass value of min_delay_btw_scans and roam_trigger_reason_bitmask
to fw.
Change-Id: I2397467a13a720e763d1181d8cd50c571f861366
CRs-Fixed: 2221785
Add new ini item "enable_ftopen" to enable/disable
FT open feature. There is no ini currently to
disable only FT open.
Add sanity check to send 11r params in case of FT open
to fw only when enable_ftopen is enabled
Change-Id: Ifb27aea8de8c8837f8eda329e1247abfadabb628
CRs-Fixed: 2214772
Add new ini item "ho_delay_for_rx" to set delay Hand-off
period. For LFR 3.0 roaming scenario, once roam candidate
is found, firmware waits for minimum this much duration
to receive pending rx frames from current BSS before
switching to new channel for handoff to new AP.
Pass value of ho_delay_for_rx to fw in case of roam
offload.
Change-Id: I19141928a2885371bc1b9e7b720473d99c4ebb1d
CRs-Fixed: 2221755
qcacld-2.0 to qcacld-3.0 propagation
Discard the original wmi interface:
WMI_PEER_ANTDIV_INFO_REQ_CMDID/PEER_ANTDIV_INFO_EVENTID,
replace with the new one:
WMI_PDEV_DIV_GET_RSSI_ANTID_CMDID/WMI_PDEV_DIV_RSSI_ANTID_EVENTID
to support chain value along with corresponding antenna info.
Change-Id: Ie9ea9d160e1ac1e2e65de422c85989159fb5a556
CRs-Fixed: 2220759
The following changes are added for Tx capture/Mcopy mode
1. Append ppduid for FW generated mgmt. frames
2. Append ppduid received in mgmt. TX completion for host
generated mgmt. frames
3. Reuse nbuf received in HTT msg to send mgmt. payload to
upper layers
Change-Id: I073cafa6389ed1ed835cc3ba4b9421b7a4b97d7f
CRs-Fixed: 2185543
Add macros to set and get BSS color value and the BSS Color
disable bit values. These macros are used to construct the value
to send to the WMI BSS Color vdev param with BSS color and BSS color
disable status embedded.
Change-Id: Id0721a1a5d66fff5d2c50708aeefb5e0ec03e999
CRs-fixed: 2186897
Deprecate enum wmi_dwelltime_adaptive_mode and use enum
scan_dwelltime_adaptive_mode defined in scan component.
Change-Id: I9c33b852172d9208fb8440c6dc71a12aefd717da
CRs-Fixed: 2213074
WMI_VDEV_PARAM_AUTORATE_MISC_CFG is introduced to set
HE GI LTF combinations in case of autorate adaptation.
Add support for the same in host side wmi files.
Change-Id: Idf567d771539b17e669ddab8b85092e3cbf9d3c8
CRs-fixed: 2204393
There are instances of use of older A_UINT/A_INT.
Replace all such instances with the qdf u_int*_t/int*_t.
Change-Id: I7ce29b03f29a0d1a0cf87cfd3c846f4694da4c2a
CR's-Fixed: 2210869
IPA module has been moved to CLD component under the converged
driver model. Point the wmi API's and structures to the newly
defined files.
Change-Id: I96205f7cc18dbea1c05a5f6314490ea6b3dd75fd
CRs-Fixed: 2180176
The WMI_MAX_CMDS macro was defined in wmi_unified_priv.h, move it
to wmi_unified_param.h so that it can be used to set
wmi_unified_attach_params.
Change-Id: I33aaa3c1fb189c7ef660ccbc5262afd0a1ee258b
Firmware recently exposed two new resource config fields,
num_packet_filters, and num_max_sta_vdevs. Add these fields to the
host-side resource config struct so appropriate values can be populated
and communicated to firmware.
Change-Id: I951ba6ac929c38c2d78af6705f4922b62fc7d3a1
CRs-Fixed: 2201876
In WMI struct target_resource_config is obsolete and outdated.
Correct resource config struct is target_resource_config hence
remove the obsolete and outdated struct target_resource_config.
Change-Id: I23aeb46854008dabad4ece953c6eb2c151bedac0
CRs-Fixed: 2202520
Extend wmi interface command to support other
connectivity check stats(ICMPv4 and tcp).
Change-Id: I881aaeab6e3e1f36b7153630b87a07019660d896
CRs-Fixed: 2168412
Add function for extract_nfcal_power_ev_param and
register wmi_pdev_nfcal_power_all_channels_event_id event
to support noise floor in HK.
Change-Id: I6eef823b507be94c65df026664244eec7fc07e24
CRs-Fixed: 2157972
Add command support to not send ADDBA REQs.
The corresponding WMI VDEV param ID to set the
VDEV param has been added.
Change-Id: Id53f8101a61ccc0aba2a9a6735d1c6942ba3592d
CRs-fixed: 2188560
Firmware will use this configuration to enable/disable the
CCK transmission. By default, the CCK Tx is enabled.
CRs-Fixed: 2191524
Change-Id: I165c3ea10ea3734fc81e7d25fe8ad676afd1b2c1
Added extender service support for obss and obss color
Collision offload support.
Change-Id: Ifd249b3bbf4510297f15beb33df13d6c4f9d7d0e
CRs-Fixed: 2185238
Current Spectral module uses qdf_print. To improve the control over
logging, use module level logging
CRs-Fixed: 2165341
Change-Id: I205991347453c4dcc424ba1958e309b7c5fb71a0
As part of converged architecture wmi_service_enable is converged
and should be used instead of WMI_IS_SERVICE_AVAILABLE. The events
also need to be defined as part of array for mapping to converged
event id's.
Change-Id: I9ab342a5cf6e665a3eb90eeef6d10bf3c145049d
CRs-Fixed: 2186338
command:-
1. "iwpriv athx s_txpow param1 param2"
2. "iwpriv athx g_txpow param1"
param1 = frame_type<<8+frame_subtype param2 is power_value
if subtype == 0xff means set all subtype of that frame type
Change-Id: I8c68e1ca6a5829a3f0cf01b2c32c3332e1010243
CRs-Fixed: 2175241
Increase the maximum value of unit test arguments to 100 to include
support DL OFDMA RU allocations for testing / debug.
Change-Id: I33ed8d53931e33cc00069653ea38b543339203c0
CRs-Fixed: 2175616
Add WMI support for enabling/disabling the FW scheduler APIs and stats
per peer for MU and OFDMA
Change-Id: I185ca6ff5b564fc9b83007fd4e37da82b5c9976e
CRs-Fixed: 2169179
Add WMI support to set SU and MU TX beamforming sounding interval on
host driver in addition to enabling/disabling the above ability.
Change-Id: Ic3ea109e47c0df13db2c919bbcdf5fc7d6164698
CRs-Fixed: 2169176
Added a WMI command to add and del peer from the list
of non associated clients for which the RSSI stats
need to be populated
Also added event handler to extract the rssi stats
from the WMI event
Change-Id: I9880c74798c13a52e1498b81735ad78f86fa41b8
CRs-Fixed: 2148773
Recently change "qcacmn: Add SAR power limit configuration"
(Change-Id: I0a214a2af780e9dd8c381c4e9eaa7d8cab6ef853) added the
ability to dynamically configure Specific Absorption Rate (SAR) power
limits. Now add the ability to retrieve the current active power
limits.
Change-Id: I7a6071dee71300daa3a217780ff3523604a11795
CRs-Fixed: 2161451
Add new WMI EVENT, SW FILS Discovery Alert Event, to get
firmware trigger to transmit FILS Discovery Frames.
Add WMI command to send FD frame buffer to firwmare.
Add WMI command to set FD period interval in mili seconds.
Change-Id: I8cb6279ec4431b9236bd32c548228a0dc6598664
CRs-Fixed: 2118098
Add ini to configure BTM offload configuration
which is sent to firmware as part of RSO start
via wmi btm config cmd.
Change-Id: I69c792705b208014af8f1878f7645d957dde6c06
CRs-Fixed: 2105112
DISA feature has been moved to a CLD component under the converged
driver model. Point the wmi API's and structures to the newly defined
files. Define new API's to extract parameters from event buffer.
Change-Id: Ia47d3682217e7ce9c021bb2db8319483c881b3b2
CRs-Fixed: 2161963
Add host support to enable setting MSDUQ depth parameters per
TID per peer.
Parameters include MAC Address, TID number, update mask and
Q depth threshold value.
CRs-Fixed: 2162460
Change-Id: Ie947fd599278a04e13d6aa6c89f840187dbf17fa
