As part of regulatory cleanup, wlan_chan_to_freq() is removed.
Use wlan_reg_legacy_chan_to_freq()/wlan_reg_chan_band_to_freq()
instead of wlan_chan_to_freq().
Change-Id: I9d105863f8d6384c97e8219b89a230c863e29d19
CRs-Fixed: 2933440
The WTC parameters are stored in MLME vdev private object.
So the parameters are cleared once vdev delete is done.
Move the WTC parameters to psoc->mlme_cfg to retain the
values across disconnections.
Change-Id: Icecfbef19af994f8a05622501d435bfb63beca50
CRs-Fixed: 2959715
Existing INI disable_4way_hs_offload is defined as a boolean
that controls the EAPOL Handshake to be offloaded to Firmware or
Not. There is no way to specify the EAPOL offload per AKM.
Hence extended the support of EAPOL handshake offload to firmware
per AKM by converting this INI to a bitmap integer.
With ini value as 0 by default Firmware takes care of 4-way HS
during roam for all AKMs except for SAE and OWE. If
this ini value is 1 then Host takes care of EAPOL for all AKMs.
Having the backward compatibility, added a new value to ini.
If this ini value is set to 2 and also if the SAE EAPOL offload
service bit is set by Firmware then the behavior is same as ini
with 0 except that Firmware takes care of 4-way HS for SAE roam
as well. And for OWE it is still handled by supplicant.
To achieve this, new roam offload flag is introduced to indicate
Firmware about SAE roam EAPOL offload, So that in Roam sync
indication Firmware will inform the status as connected but not
authenticated so that supplicant can take care of 4-way EAPOL HS.
Change-Id: I8b65a1768fad91fac7e427712d3ccf4586176f5f
CRs-Fixed: 2955029
Change direct RX TLV usage to using HAL APIs to populate RX packet
capture params.
CRs-Fixed: 2888534
Change-Id: Ib20e72ddb214e2579d2eabb92630604dc5b88526
Add the changes in FISA/pkt-capture APIs due to the
modifications in the hal APIs to get rx tlv params.
Change-Id: I5b1827079ca2e056da0db5e396ca90aec57f559b
CRs-Fixed: 2888534
TWT is supported in STA/SAP vdevs and it's allowed only in
DBS/Standalone case and not in SCC/MCC. Disable SAP TWT if
1. Concurrency occurs in SAP + NAN/NDI vdev
2. SCC/MCC occurs after CSA
Change-Id: Id1400bd5555d2f48590d7d3ad7c70162d1dd92fb
CRs-Fixed: 2942959
TWT is allowed only in DBS/Standalone case and not in SCC/MCC.
Handle TWT if any session request comes in SCC/MCC or DBS case
as per below:
1. If TWT session request comes on standalone SAP then peer
client will initiate the session and not from userspace
(SAP DUT)
a. Send twt responder enable command and
b. Send twt requestor disable command to firmware
2. If session request comes on standalone STA then
a. Send twt requestor enable command and
b. Send twt responder disable command to firmware
3. If two vdevs are up and SCC/MCC exist
a. Send beacon template with twt responder disable command to
SAP vdev
b. Send twt requestor disable command to STA vdev
4. If two vdevs are up in case of DBS
a. Send requestor enable command for STA vdev
b. Send beacon template with responder enable command for SAP
vdev
5. If 3 port concurrency comes then
a. Send requestor disable command to STA vdev and
b. Send beacon template with responder disable command to SAP
vdev
Change-Id: I65994702bb72d5006bd66b2ef57a0704a67410f7
CRs-Fixed: 2938961
Fix some LFR2.0 issues for connection manager path as below:
1: Add ptr null pointer and len check before access
rsp->connect_ies.bcn_probe_rsp.
2: Remove aged AP threshold check so that roam process can find
candidate AP with more probability.
3: Set cm_ctx->vdev to cmd_info.vdev in
cm_remove_preauth_cmd_from_serialization().
4: Add more debug logs for preauth part.
Change-Id: I4b0766bba40e3ebc3d01bdd4ae59aec1ec3a21d9
CRs-Fixed: 2961151
Remove duplicate code in connection manager and call
same API from connect complete and roam complete.
Change-Id: If7e9e1069acb1dede9433d16ef96f37029ff716d
CRs-Fixed: 2960921
Send TDLS STA notify only when connect is success.
This is required as incase connection, it will increment
tdls_soc_obj->set_state_info.set_state_cnt.
It that connection results in failure, then also, without
this check this count will increment.
For subsquent connections, in tdls_send_update_to_fw()
because of incremented count, it will be treated as
FW Set State is already sent and will not send it
which will result in FW crash while adding TDLS peer.
Change-Id: Ic3bedfb1357ac703f98d2d0285dcc85605bab97e
CRs-Fixed: 2955401
When ipa setup pipes fails in wlan_ipa_uc_ol_init API,
tx buff mapping is not done but during deinit path
tx buff unmapping is called without mapping.
Fix this by resetting uc_loaded flag to false when ipa pipes
setup failure is encountered.
Change-Id: Ic34320e56cee9e60381d9203dd95e268d0ef392b
CRs-Fixed: 2957612
In the scenario where ipa connect pipes fails in the
wlan_ipa_uc_loaded_handler API, uc_loaded flag is not
reset. As a result of this, in wlan_ipa_uc_ol_deinit,
ipa_tx_buf_smmu_unmap and ipa_wdi_disconn_pipes APIs are
invoked incorrectly.
Fix is to set the uc_loaded flag to true only if connect
pipes and tx_smmu mappings are successful in
wlan_ipa_uc_loaded_handler. Also, initialize the uc_op_work
in wlan_ipa_uc_ol_init prior to the uc_loaded check to
avoid a possible race condition which could also result
in the similar issue as above.
Change-Id: I119170413cb9b5e03ec476c9a69d9effaa460c01
CRs-Fixed: 2940833
Currently, osif_request_alloc is done and waiting for response
after posting the message NDP_END_REQ. But this may lead to
invalid memory access if message gets processed in scheduler
thread and response also comes before the request is allocated.
Allocate the request before sending message to avoid this.
Change-Id: I88b0a8be229e779526f0f3cf184b191e00872ee8
CRs-Fixed: 2782045
Currently, cp stats are received through kworker thread context.
This causes race conditions/out of sync issues if any common data
structures are handled in parallel in scheduler thread context.
There is no need to receive the cp stats on kworker thread as per
current design. So, move the cp stats event handling to scheduler
thread to avoid any race conditions.
Change-Id: Id8134003e6f7a3e0368b20c496f650e0b7025b9e
CRs-Fixed: 2928876
Currently in WTC mode the candidate AP RSSI threshold
configuration is applied for candidates on all band.
Add support to configure the candidate AP RSSI threshold for
different bands.
Change-Id: I94442c0f1bd3ea20dc2f5ebe893a9ead7fb8d890
CRs-Fixed: 2951610
Set intermediate EP vote access before host
wake up indication smp2p is sent to F.W,
this helps to avoid smp2p override.
Change-Id: I4b998ee5ea6b26921855bfbae434869fb93accf9
CRs-Fixed: 2953883
Only do cleanup roc request and notify tdls sta disconnect
when sta disconnection operation is from osif or north bound.
Change-Id: I1d0aa4f1cd8a23baca890228485f22124eeabf78
CRs-Fixed: 2954772
Roam offload init command should be sent to firmware only
for STA mode. For P2P vdev, if roam init command is sent,
it causes abnormal target behavior.
Don't send roam init command if the vdev opmode is not
Station.
Change-Id: I0bfc3c6b4bc2eef7459b092101bc4d72c68761e5
CRs-Fixed: 2924563
1. Currently, the same twt enable api hdd_send_twt_enable_cmd()
sends to firmware for both requestor and responder role.
2. When firmware receives enable command, it will be busy to
handle that command. If any back to back enable command, it can
lead to some issues.
As part of this change, decouple enable api based on requestor
and responder role as per below:
for requestor: hdd_send_twt_requestor_enable_cmd()
for responder: hdd_send_twt_responder_enable_cmd()
Synchronize twt enable command to avoid back to back command
issue.
Change-Id: I3d3840740fee7413d6123ece919c42558e9b35d1
CRs-Fixed: 2937540
Currently there is no support to enable NAN on indoor channels,
as per the new requirement add an ini support to enable NAN on
indoor channels.
Change-Id: Ia3acbc133cab4865d8ad69992e893be91439f50f
CRs-Fixed: 2943668
Currently, reg_wifi_band enum is compared with
enum band_info. different values may lead to
invalid chan mode.
Fix is to compare reg_wifi_band with reg_wifi_band
enum value only.
Change-Id: Ibbe83ab5a8a428528bbeb28c941552a6f412a844
CRs-Fixed: 2949501
If HO fail/ roam abort is received without any roam start indication
the roam command will not be present in connection manager, so
continue with cleanup even when roam command is not present in these
cases.
Change-Id: I0ff3307b4d4ba96cc3b0c413fd0a41be47e9c588
CRs-Fixed: 2948064
Add support for TWT get_status command in SAP
As part of this change, TWT get_status command is supported
if
1. If particular dialog_id and particular mac_addr are
present
2. If dialog_id = 0 and particular mac_addr are present
3. If no parameter present
Change-Id: I5ce1719da7f9a3988ba6e1f04455a06faf9687c6
CRs-Fixed: 2937999
Reset iface_context to NULL if max IPA interfaces reached to avoid to
cleanup the wrong interface context when setup IPA interface failure.
Change-Id: I2f19d62b9f76f826c2275a0d889b5f5a0a48a01f
CRs-Fixed: 2931966
Fill he and vht parameters in data tx and rx packets for packet
capture mode to update in radio tap header.
Change-Id: I229fc41657456b9ab5d8a2dfce1cdd039b624fcb
CRs-Fixed: 2942108
Currently centre frequency filled in data rx packets for packet
capture mode. Need to fill base frequency so filling frequency
from connection policy manager.
Change-Id: I79abe4e8a27a853c156eff8618be2f280fc54e78
CRs-Fixed: 2942107
When updating the scan filter with valid channels, refer to the MLME
channel list instead of the policy manager list. The policy manager list
is used mainly for SAP related APIs.
Change-Id: I5530e5bcfd6b5c04063d7530fbc996ffca91df3f
CRs-fixed: 2946365
In any start BSS or ACS related function, change the calls to regulatory
to access the secondary channel list instead. This list will hold the
VLP channels specifically for any beaconing modes. This allows a client
and an AP to operate simultaneously on different power modes.
Change-Id: Ic06b408ebcc78292d84f1f035c00bf39a23de3ca
CRs-fixed: 2944484
When vht cap indicates the vht max MPDU size >= 7991 supported,
ht cap A-MSDU length field should indicate 7935 octets
supported according to 80211 specification.
At present no WMI HT cap defined for ht cap A-MSDU length field
from target.
Fix the issue by override ht amsdu len to 1 if vht max mpdu
len >= 7991 supported by target.
Change-Id: I9d2b8c11e7a27e016f618c1a2c8a380d081a6ba7
CRs-Fixed: 2929148
Sometimes we need PDEV suspend mode, WMI_PDEV_SUSPEND_CMDID and
WMI_PDEV_RESUME_CMDID. But currently design, only support WoW
suspend or not support two choices. And, there are two confused
ini configuration, gDisableWow and gEnableWoW.
1. Add new ini gSuspendMode to set suspend mode. Default 2.
0, does not support suspend
1, legency pdev suspend mode
2, WoW suspend mode
2. Clean gDisableWow. It is replaced by gSuspendMode=0.
HDD suspend/resume function get the value by new API
ucfg_pmo_get_suspend_mode().
Change-Id: Icbeef3df6879ca2054f64e0292e9b9469c4936d4
CRs-fixed: 2940788
The INI skip_tpe_consideration when set, skips power from AP's
TPE IE in TPC power calculation for 2.4G/5G case. Enable this
INI by default since APs advertise low TPE powers for IoT, thus
lowering overall TPC power.
Change-Id: I6c07bbd684579c2fa3617e49d76c75b5bf3f2815
CRs-Fixed: 2941630
Drop non-EAPOL/WAPI frames from unauthorized peer received
in the IPA exception path.
Change-Id: I0c0bc6e60efa193126ba1e3eca36c5e02f7f76a3
CRs-Fixed: 2860206
During DUT STA Rx over IPA, qdf_spin_unlock_bh is called as following.
__wlan_ipa_w2i_cb
->wlan_ipa_rx_intrabss_fwd
->cdp_ipa_rx_intrabss_fwd
->dp_ipa_rx_intrabss_fwd
->dp_vdev_get_ref_by_id
->qdf_spin_unlock_bh
netif_rx will raise NET_RX_SOFTIRQ in enqueue_to_backlog->
____napi_schedule even NAPI not enabled.
spin_unlock_bh will call do_softirq to execute NET_RX if NET_RX_SOFTIRQ
is raised.
If qdf_spin_unlock_bh is called in wlan_ipa_w2i_cb, once 1 skb received,
netif_rx is called, and NET_RX_SOFTIRQ and APP like iperf is scheduled,
too much context switch happens, CPU and power is wasted, Rx throughput
KPI failed on mdm platform which only has single 1.2G-1.5G CPU.
Fix it by avoiding intra bss forwarding for adapter in sta mode.
Change-Id: I264b14120b9998a56f6c1978f5a890615e6f837c
CRs-Fixed: 2915691
At present LTE unsafe channel switch and DCS is using
hdd_switch_sap_channel to switch channel of SAP.
hdd_switch_sap_channel has no bw setting parameters and just
use the original bw of SAP - ch_width_orig. The ch_width_orig
(80Mhz) may not be applicable if SAP is channel switching from
5G 80Mhz to 2G. Use the new API wlan_get_ap_prefer_conc_ch_params
to override the bw to appropriate value for the new channel.
Change-Id: I9ab6c92a0534517c524bd56b0c3087d7f75f6368
CRs-Fixed: 2939654
Reset the value of static variable rssi_comb to zero when
last mpdu of ppdu is received in packet capture mode.
Change-Id: Ida76dfb9c98a8e2718844f890e0303802db5bbed
CRs-Fixed: 2940871
