Currently, gRoamBeaconRssiWeight is not used in HOST or
FW.
Remove unused roam ini param gRoamBeaconRssiWeight.
Change-Id: Ida6ddb8ca5805f819c4d3f7e6ed96c705fa6594f
CRs-Fixed: 2767533
Pass rx data rssi triggers and rx time to firmware.
Add log in wmi to narrow down host and firmware issue.
Change-Id: I255e02ab8f2c88a29619a49d9c2055bdaa75642a
CRs-Fixed: 2768053
FW triggers roaming based on the RSSI score of AP(s) available
after background scan. Currently, the host does not configure
the value of bg_rssi_threshold RSSI. This results in ping-pong
roaming after background scan, even though candidate AP
RSSI is not better than 5dbm than connected AP.
Fix is to configure the value of bg_rssi_threshold via new
INI "bg_rssi_threshold" and configuring default value of
INI as 5dB.
Min: 0
Max: 100
Default: 5
Change-Id: Ib710e294c8b33ff4903d41453e3b55f02daf53ae
CRs-Fixed: 2763962
SAE Public Key (SAE-PK) authentication is an extension of SAE. Host adds
support for SAE-PK APs roam score which host uses to select AP for initial
connection and roaming.
Change-Id: Id8c420950bb8c1d11db5a26aa860e280bcb672d1
CRs-Fixed: 2769372
Add checks in caller APIs to handle negative return value from
crypto get param and crypto get peer param APIs.
Change-Id: Ibb138971f347c7ccdacbc93aa38521d5d9536759
CRs-Fixed: 2775328
Currently, the APIs related to setting the preferred channel list is
in the SME module. Move these APIs to the policy manager so they can
be accessed from non-legacy modules.
Change-Id: Icc487dd2a0014e59db9c2df729b875f58e3e975e
CRs-fixed: 2766863
3 ini:
roam_data_rssi_threshold_triggers
roam_data_rssi_threshold
rx_data_inactivity_time
If there's rx activity during latest rx_data_inactivity_time
and avg of data_rssi is better than roam_data_rssi_threshold, then
suppress roaming triggered by roam_data_rssi_threshold_triggers: low
RSSI or bg scan.
Change-Id: I5b41c4119e61392b50e52ab8ccb8650e5758f3b3
CRs-Fixed: 2768053
Set default value of INI enable_subfee_vendor_vhtie to 1
to enable SU Bformee in vendor VHTIE by default.
Change-Id: I8a916495dd5c6ddfe78840dc6f35976fbdbbf8ba
CRs-Fixed: 2769257
This is a change for typo about LFR configuration. It uses ini -
"mawc_roam_ap_rssi_threshold", the correct is
"mawc_roam_rssi_high_adjust".
Change-Id: I7e29287b84559f58f13d191d6288534196b894da
CRs-Fixed: 2768752
Currently INI: gFirstScanBucketThreshold is not used
while LFR2/LFR3 roaming.
Remove unused INI gFirstScanBucketThreshold
Change-Id: Ifa909fc57d3ac3da696369fcffc390826f393b44
CRs-Fixed: 2767372
Add changes to send roam scan mode over RSO start/stop/update_cfg
from connection manager. Update the roaming params and roam scan
params to new structure.
Refine send_roam_scan_offload_mode_cmd_tlv().
Change-Id: I6adce2e8a24ece93a079032d0e66760393fcdccd
CRs-Fixed: 2766023
Increase max sae auth frame retry count to 3 since total SAE auth
timeout is 5s.
Change-Id: I5902cc3411f713eaeed5ef7754fe7fe8e590b459
CRs-Fixed: 2765211
In some instances, AP does not respond to probe req
causing join timeout at STA and no connection.
To solve this,send multiple probe requests(every 200ms)
to AP until join failure timeout(1 sec) expiry,
if single bssid case retry same bss again
(configurable via ini, max allowed tries 2).
Change-Id: I7a7eeedcc24db1a74cd186ff957c638a39cdea6d
CRs-Fixed: 2763815
Currently the driver enables the SRD channels
support for both P2P_GO and SAP if the SRD master
mode is enabled.
Have individual ini values to enable/disable
the SRD channel for each op-mode as required.
Change-Id: If6e66996ed19dacbde7f71a6702f378a7e9a273c
CRs-Fixed: 2748446
The ini ratemask_type and ratemask_set can be used to limit
the maximum phy rate. The ratemask_type is used to select
the phy mode and the ratemask_set to select desired NSS and MCS.
It can be used to optimize link performance.
Change-Id: Ia5c9f3a80eb93710bdcf53dabc4a45e554753b01
CRs-Fixed: 2758859
Add user configuration support to configure dot11 modes for
different vdev types.
Change-Id: I338d9d76f000195d1798bbc8b3b7ff1fb33ee305
CRs-Fixed: 2760240
If join fail reason is timeout, retry sending join req
after timer expiry, timer value can be configured
via join_failure_retry_interval.
Change-Id: If90071b3f6d7f48936db6f7088c3c1547e48b294
CRs-Fixed: 2760236
RRM 11k feature is enabled or disabled based on the
rrm_enabled flag. rrm_enabled is filled from the gRrmEnabled ini.
Change the default value of gRrmEnabled ini to 1.
Change-Id: Ie2a95293c3225abc667563fcc9eed8440e46727f
CRs-Fixed: 2754534
When sta_sap_scc_on_dfs_chan = 0, SAP is not allowed to SCC
with STA on DFS channel. Check the SAP target channel DFS flag
considering the target channel bandwidth.
Change-Id: I321c1055574477fe39ca8569f24a4040c8dc1904
CRs-Fixed: 2756518
Add changes to define structure to hold the WMI_ROAM_SCAN_MODE
command related parameters.
Also added minor cleanup changes.
Change-Id: I24ef18e05de8dd05ee437e440651ea9ab0731e46
CRs-Fixed: 2758316
Enable RX LDPC capability by default in the
driver sinc the ini gEnableRXLDPC is not present
in the WCNSS cfg ini file.
Change-Id: I826dca94e0db18713b0d87581da07eeefbfc80d4
CRs-Fixed: 2748730
Add support to retry the deauth frame if the Tx is not success if
user configured the retry count.
Change-Id: Id128b4a70a276ee86270372ff7954e40bde8123c
CRs-Fixed: 2754305
In roam trigger print the driver doesn't include the current
RSSI threshold info.
Add the current rssi threshold value at which roaming was
triggerd in roam trigger logging.
Also refine the candidate AP blacklisting related prints.
Change-Id: I6d39851278081a728b74e036c22e8d302d7b7b4c
CRs-Fixed: 2752998
Use ROAM_11KV_CTRL WMI vdev command to enable/disable the roaming
functionality in FW.
Change-Id: If3bb344ec7058d4149d0064975d7c91f213fd105
CRs-Fixed: 2727671
Host sends the WLAN_MSG_WLAN_STATUS_IND to WiFi Location Service(WLS) via
cnss daemon which includes supported channels. WLS service is yet not 6GHz
capable. Hence to limit the 2.4GHz/5GHz channels only in
WLAN_MSG_WLAN_STATUS_IND introduce new INI "wls_6ghz_capable".
Change-Id: I77b284d2025601fec72aa35d430f18865f15f247
CRs-Fixed: 2748489
CLD driver specific time sync feature is no longer used since
core BSP provides more accurate time sync over QMI and hence
disable CLD driver specific time sync feature to avoid periodic
wake ups.
Change-Id: Ic2790e7cdb6cf56f874fb56cda246777bc34d2e3
CRs-Fixed: 2715021
Print BTM BSS termination timeout value and BTM MBO assoc
retry timeout value coming from FW through
wmi_roam_trigger_reason_tlv_param tlv.
Print Blacklist reason, Source of adding AP to BL, timestamp
which indicates the time when AP added to blacklist and
Original timeout value in milliseconds when AP added to BL
coming from FW through wmi_roam_ap_info_tlv_param.
Change-Id: Iea5b8c136f83841d679b9ad06721bb0c9349b46a
CRs-Fixed: 2744250
Currently driver sets the NOL state of the channels to false
on every regulatory updated, which indicates the channel is
not in NOL. Which may lead to some issues where the channel
is actually in NOL but host treats it as non-NOL channel.
Ideally NOL list should be maintained throughout the driver
lifetime and across the regulatory changes.
To address this issue add a logic to not update the NOL state
of the channels whenever the regulatory update is received.
CRs-Fixed: 2744916
Change-Id: If96b22ab29a60a2aa752bbf01aaae46fc37362eb
Add changes to include new roam scan sub-reasons in host driver
roam logging and refactor few existing string.
Below are the new reasons:
WMI_ROAM_TRIGGER_SUB_REASON_LOW_RSSI_PERIODIC
WMI_ROAM_TRIGGER_SUB_REASON_INACTIVITY_TIMER_LOW_RSSI
WMI_ROAM_TRIGGER_SUB_REASON_PERIODIC_TIMER_AFTER_INACTIVITY_CU
WMI_ROAM_TRIGGER_SUB_REASON_PERIODIC_TIMER_AFTER_INACTIVITY_LOW_RSSI
WMI_ROAM_TRIGGER_SUB_REASON_INACTIVITY_TIMER_CU
Change-Id: I1aeb48d29561b48ac7b8762626fa0050f4fb9030
CRs-Fixed: 2742558
Change the usage of cfg parameters from Internal/External
to External in .h description for mlme, p2p, and
policy manager files.
External means that both internal teams and external
customers can modify the parameters.
Change-Id: Ic1e68d5a90be2c898ce66aa18e8d91f16561b408
CRs-Fixed: 2712773
Check the required security types allowed for 6GHz connection and
do not allow the connection if the secutiry check fails.
Change-Id: Ic680c4600b3f17151e42f8708ff8810e5d16e52e
CRs-Fixed: 2715086
Add new channel 177 to wiphy struct ieee80211_channel
hdd_etsi13_srd_ch and rename the struct to
hdd_5dot9_ghz_ch.
Add a new ini fcc_5dot9_ghz_chan_in_master_mode to
enable/disable new 5.9 GHz channels 169, 173 and 177
in master mode.
Change-Id: I68dc3be18277ca0e416a579327f406279458899e
CRs-Fixed: 2693707
Add macro ROAM_OFFLOAD_V1 for new code and implement below functions
for connection manager roam part:
csr_handle_roam_state_change() roam offload state related handler.
Filling WMI_ROAM_SCAN_RSSI_THRESHOLD cmd parameters related process.
Change-Id: I0351155ca5a3d68ade6568c7527c5708582ccf1a
CRs-Fixed: 2730826
The event WMI_ROAM_STATS_EVENTID is received after
every roam, once the roam synch complete is sent by the host.
This event contains details regarding the btm response.
This helps in debugging/understanding the scenario when roam
failure happens.
Print the info received related to btm rsp and roam initial
info into kmsg.
Change-Id: Icb2058eed5df3265018b3c53548d123f3a4faf4f
CRs-Fixed: 2728267
The band_capability field is used in other places to be
a bitmap over reg_wifi_band. Update the field in wma_tgt_cfg and
wlan_mlme_generic to take the same bitmap for consistency.
Update all references to these fields to expect a bitmap as well.
Change-Id: I8abd697e2fbe02b4eadd32f3027bef7408bac2a0
CRs-fixed: 2726710
Introduce new INI sae_connect_retries to decide auth (initial connect
and roam auth) and connect retry for sae. MAX reties is capped to 2
and max for roam auth is 1.
Default is 0x49 i.e. 1 retry each.
Bits Retry Type
BIT[0:2] AUTH retries
BIT[3:5] Connection reties
BIT[6:8] ROAM AUTH retries
Change-Id: Idae86a7bdb32244c7f3a140b8591418b8238758a
CRs-Fixed: 2728458
Rename the existing roam offload states to include
WLAN_ prefix. Add 2 new states:
WLAN_ROAMING_IN_PROG - Roaming has started at firmware, this is
after candidate selection at firmware.
WLAN_ROAM_SYNCH_IN_PROG - State after handoff is complete at
firmware.
Also move the roam_offload_state enum to connection manager.
Change-Id: Ib1f38d200393849253893113172cdfc69e381fb3
CRs-Fixed: 2725387
Enable compilation of the connection manager roam files with
Kbuild changes.
Add new API to store and retrieve the firmware scan channels at
mlme. Also add initial support to post SET_PCL command through
lim, so that it is not sent before ROAM init command.
Add changes to restrict connection of the 2nd STA to
channels on the other band of the 1st STA connected band.
This is done by filling only the allowed band channels in
the scan filters for the 2nd STA connection. If only
1 STA is active, it is allowed to connect on any band.
Add header gaurds for missed header files:
wlan_cm_tgt_if_tx_api.h
target_if_cm_roam_offload.h
Change-Id: Id2bce12b9663ed635ea46164169b088461aab870
CRs-Fixed: 2720341
Currently, powersave configuration is being overwritten before INIs
are initialized by mlme component. As a result INI configuration is
not being overwritten in case of monitor mode.
To resolve this issue, overwrite PS configuration during start
modules and restore it in stop modules.
Change-Id: I2707b431b81881c943104b211d55c6f48f348ba9
CRs-Fixed: 2682164
In 11ax draft 6.1, the 6G starting frequency has been shifted by 10 MHz
to the right. Change the default channel value of INI "normalize_acs_weight"
accordingly.
Change-Id: I6b08f3c604f4410dbddf25bbe7c7491047b676ea
CRs-Fixed: 2695542
Add new ini enable_dual_sta_roam_offload to enable/disable dual
sta romaing feature. Enabling this ini will allow firmware to
roam on both the vdev if firmware supports dual sta roaming and
the hw is dbs capable.
This ini will be checked in the dual sta roaming offload state
machine to enable roaming on both the STA or to fallback to the
current implementation where first connected sta will have rso
enabled.
Change-Id: I04f141ac31e0f168b6f19fe878bca219a36cfae7
CRs-Fixed: 2709036
Currently the driver supports the dynamic
configuration of nss and chain to FW for
VDEV if the FW advertises the capability
of supporting the same. However there is
no support to overide this.
Fix is to have an ini to enable/disable
this feature of configuring the dynamic
nss and chains to FW.
Change-Id: I0b84bb5aec53966a43a00c11d4aba3863414005c
CRs-Fixed: 2708303
