Send responder pm mode info in twt setup event and twt
get session parameter response.
Change-Id: I1f58e0bed62f152d84cec20ff7924d05e126347f
CRs-Fixed: 3029014
FW sends Spectral scan detector info TLV in WMI_PDEV_SSCAN_FW_PARAM
event to indicate the information of a detector participating in a sscan
session. FW sends one TLV of this type for each detector participating
in a spectral scan session. Add support to process the TLV and update
the spectral host data structures accordingly.
CRs-Fixed: 3044193
Change-Id: Ie17b6ea9336ada7a00e4594fa2f7f49ef3d443e5
FW sends Spectral scan chan info TLV in WMI_PDEV_SSCAN_FW_PARAM_EVENTID
event to indicate the channel information for a spectral scan session.
Add support to process the TLV and update the spectral host data structures
accordingly.
CRs-Fixed: 3044162
Change-Id: Ibbf7f6bbbb267123bbdf44bcfffa2cfb1c2926df
On Beryllium architecture, PHY DMA applies a 32-bit byte swap to assist
in efficient Host reads when connected to a big-endian Host.
This is done to avoid byte swapping at the Host.
So, if the Host reads this data 32-bit word at a time, the byte order
would be intact. Report headers are not a problem because as they are
composed of 32-bit words. For FFT bins, read each DWORD at a time and
extract FFT bins out of that DWORD. Make this change in a generic way to
keep the design uniform across different chipsets and endian modes.
CRs-Fixed: 3042188
Change-Id: Idff1ac7eb5e18c692c9ee8b19b9ae9e6b962d486
There is a requirement to use REGDMN and wireless modes in UMAC layer of
the cmndev component. As the WMI_HOST_REGDMN modes currently are defined in
WMI layer, we can't use them directly in the UMAC layer. Hence move them
to the reg_services_public_struct.h and rename them as HOST_REGDMN modes.
Replace all WMI_HOST_REGDMN instances with HOST_REGDMN. Wireless modes are
currently defined in WIN component, use them to cmndev component.
CRs-Fixed: 3044590
Change-Id: Iee5fa1745a1a44b834334746b10bdbb6f6563a0a
Add change to handle service_ready for,
1. Ema multi-MBSSID group support
2. Large beacon support greater than 1.5K
CRs-fixed: 3036717
Change-Id: I1c985faf429aacd78ae74fe0ffe18958fd6aa821
The flag WMI_SERVICE_HW_MODE_POLICY_OFFLOAD_SUPPORT indicates
whether HW mode selection offload is supported by firmware or
not.
If it's advertised in service capability, host should not set
HW mode explicitly, firmware takes control of managing HW mode.
Change-Id: I8939b44fd7ed3a674c4da91524c5d5622bf67ce7
CRs-Fixed: 3017054
Add support for AFC specific Host service flags to switch
between LPI only and SP+LPI, disable AFC timer and request ID checks
in target.
Change-Id: I34d6adcad6e4a2cd6383c941ed07b98059daeed0
Add host WMI APIs to send WMI_PEER_ADD_WDS_ENTRY_CMDID,
WMI_PEER_REMOVE_WDS_ENTRY_CMDID, and WMI_PEER_UPDATE_WDS_ENTRY_CMDID
to the Fw.
Change-Id: I32afdac7c366b647ee3196bcb76531295e640b8b
CRs-Fixed: 2997227
Add extract_roam_pmkid_request to wmi_ops to allow cld driver
to register the corresponding callback.
Change-Id: Ifa9cd73d6d62e7411b78b15086d7e166559f6d1c
CRs-Fixed: 3014249
Add extract_auth_offload_event to wmi_ops to allow cld driver to
register the corresponding callback.
Change-Id: Ie3417f44360021570ce678ce1c3f949a92424494
CRs-Fixed: 3010510
Add support for extracting Thermal Stats Events
from thermal event TLV for FW event
WMI_THERM_THROT_STATS_EVENTID.
Also, added support for FW Cmd to request for
Thermal Stats: WMI_REQUEST_THERMAL_STATS_CMDID
Change-Id: I2bc80d082bda45e2255371bcb0c31d35d9806525
CRs-Fixed: 3016845
Add extract_roam_stats_event to wmi_ops to allow cld driver to register
the corresponding callback.
Change-Id: I77ebb05a1a2ce9fa0b2f2f2ffb50c523ab9070e6
CRs-Fixed: 3007690
WMI_MGMT_RX_REO_FILTER_CONFIGURATION_CMD is used to the configure re-order
criterion for incoming management frames. Add WMI layer support for the
same command.
Change-Id: If1498fd4fbccd86e7d54d9eac268868b36523d06
CRs-Fixed: 2960472
When MGMT Rx REO feature is enabled, FW will be sending MGMT Rx REO
parameters TLV as part of WMI_MGMT_RX_EVENTID for the frames that require
reordering. Add APIs to extract the same.
Change-Id: I57b132927cf413384d680b5778bfe6a2e2737adf
CRs-Fixed: 2960471
The purpose of the multicast Domain Name System (mDNS) is to resolve
host names to IP addresses within small networks that do not include
a local name server.
It utilizes essentially the same programming interfaces, packet formats
and operating semantics as the unicast DNS, and the advantage is zero
configuration service while no need for central or global server.
Based on mDNS, the DNS-SD (Service Discovery) allows clients to discover
a named list of services by type in a specified domain using standard
DNS queries.
Here, we provide the ability to advertise the available services by
responding to mDNS queries.
Change-Id: Ie6a3cd319d219c2f338d83f4bdbd704a090711c4
CRs-Fixed: 3008552
When MGMT frames are consumed by the FW, FW sends MGMT Rx FW consumed event
to the Host. Add WMI layer functionality for this event handling.
Change-Id: Id95f41a717b88589e861781e1111b17dc90475be
CRs-Fixed: 2959118
Add new TWT teardown status code to indicate host teared
down the TWT session due to PS disable.
Change-Id: I49c2d7bb1abc4ceb4f79b833cbafcb44e8b936fe
CRs-Fixed: 3013358
With latest architecture there are different HTT peer
data versions supported by the firmware, supported htt peer
version will be sent in the service ready and need to feedback
to the firmware in the init command.
Change-Id: Icd0470843198387cd7e0192cbe3821d45ef0534e
CRs-Fixed: 3008706
Add new field ema_init_config to signal the configured value of
beacon size while using MBSSID feature in 6Ghz.
The current allowed range is 1500-3500 bytes.
CRs-fixed: 3004041
Change-Id: Id8cc1b7e4602b2e52b8eb215337070c6e3c26089
Add P2P_P2P_CONCURRENCY_SUPPORT service capablity to
validate whether fw can support p2p concurrency
support or not. when firmware advertises this flag it
can support MCC,SCC, DBS for p2p-GO/GC + p2p-GO/GC.
Change-Id: Ifec4bf984595b06374be9024601733c8537a9c3e
CRs-Fixed: 2984165
Add a function pointer to a function that converts host vdev param to FW
vdev param.
Change-Id: I01557d8bd87cb82548114626ff726aabba01dd19
CRs-Fixed: 3005160
Add extract_roam_scan_chan_list to wmi_ops to allow cld driver
to register the corresponding callback.
Change-Id: I71b17b807d183aff31b73a4732d368d1525c118e
CRs-Fixed: 2990390
Add extract_vdev_disconnect_event to wmi_ops to allow cld driver
to register the corresponding callback.
Change-Id: I3fb891f9a0b4afc92c8a456b2a8fe17bcfecaefa
CRs-Fixed: 2990389
Add extract_btm_bl_event to wmi_ops to allow cld driver to register
the corresponding callback.
Change-Id: I1734f577b07f8c54924a83d3d367e8cdba07f41c
CRs-Fixed: 2990385
Add extract_roam_event to wmi_ops to allow cld driver to register
the corresponding callback.
Change-Id: I812105a1a81060de0de3f6b9857257e79aa23fc1
CRs-Fixed: 2990384
Add support for multi vdev set param WMI API to send vdev param for
multiple vaps.
Change-Id: If7381f0b242cacff0817e6bdc16606d3d776b48d
CRs-Fixed: 2994278
A new TLV is added to send partner link CSA/ECSA count offset to FW as
part of beacon template. Add WMI changes to populate these TLVs in the
beacon template send function.
To fix the compilation issue, added forward declaration of 'struct
vdev_mlme_obj' and removed 'include/wlan_vdev_mlme.h' include file from
wlan_mlo_mgr_public_structs.h.
Change-Id: I6e421b29bb887bec711a23db1458aca4d112ade4
CRs-Fixed: 2983249
In WMI INIT, check whether firmware supports the ack event or
not. If it supports then enable driver support and send it to
firmware during WMI INIT.
Change-Id: Icfdee6bc06e6a393de880b87fdab70665ea7c8b4
CRs-Fixed: 2987898
In case if TWT command (i.e setup, terminate, pause, resume,
nudge) comes from userspace and if the firmware is in below mode
1. scan in progress
2. roam in progress
3. CSA is in progress or
4. Any other error
then the command needs to be rejected in userspace context.
Synchronize the TWT command so that whenever command goes from
driver to firmware, then driver will receive ack event first
followed by respective event (i.e add dialog, delete dialog,
pause, resume, nudge) with below condition
1. If driver receives the ack event as successful then driver
waits for this ack event, respective event with status of the
TWT action frame over the air is expected.
2. If driver receives the ack event as failure then it will
rejects the TWT command in userspace context.
Change-Id: Ie885d98ecf2dad98d34676d889fd70e4c84f0a05
CRs-Fixed: 2987904
Add TWT service bit capability support to check whether firmware
supports ack event or not. If firmware doesn't support ack event
then service bit capability will become 0 and whenever TWT
command comes, host will not wait for ack event and sends command
in a legacy way.
This support is mainly added to handle new host and old firmware
combination.
Change-Id: I55d373c2e017130b58a4b332da16f0eda8f34eba
CRs-Fixed: 2987749
Changes to extract AoA phase delta values from WMI event.
The AoA phase delta values along with ibf calibration value
is shared to derive the phase values which is to be used in
CFR.
Change-Id: I70f50656db4194025a0b6b37c8b4a27048968e0f
Check the below service bits and set in psoc if the service is supported
by FW.
WMI_SERVICE_RTT_AP_INITIATOR_STAGGERED_MODE_SUPPORTED
WMI_SERVICE_RTT_AP_INITIATOR_BURSTED_MODE_SUPPORTED
Change-Id: I13504958bf31b2d645d915b4db20719bdc9a4133
CRs-Fixed: 2969195
Add WMI support for EHT puncturing by filling puncture
bitmap in vdev start and peer assoc commands.
Change-Id: If1d2541655558f22a96a741999ec4ff7348f695a
CRs-Fixed: 2982498
