As per the requirement, if TWT setup request is issued when
power save is disabled, expectation from driver is to return -EAGAIN.
Change-Id: I7a519d15787f912338afabf7e83b561cb3a2ebc0
CRs-Fixed: 3163880
Remove the old SAP-CSR flow for start bss, stop bss and
channel change req processing which is disabled currently
under the SAP_CP_CLEANUP macro.
Cleanup the redundant checks in the deauth, disassoc
response processing in CSR.
Change-Id: I5a360fc267688b51ca645551108b65646a3c8c1a
CRs-Fixed: 3164259
Consider a case when CSA happens and south bound disconnect
command(WLAN_SER_CMD_WM_STATUS_CHANGE) got queue in serialization
at same time. Later peer tries to connect and south bound
diconnect command becomes active for same peer.
As part of CSA, peer gets deleted directly without going through
serializtion. So when south bound disconnection command becomes
active, it may lead to race where peer tries to connect and
driver tries to disconnect the same peer which may cause
deauth/disconnect(WLAN_SER_CMD_WM_STATUS_CHANGE) active command
timeout.
As part of fix, flush all peer disconnect/deauth pending commands
from serialization during CSA.
Change-Id: I9b0af7deb7f2123850f3535f2d3258440af381f1
CRs-Fixed: 3148874
Remove SME global lock use from the scan APIs as scan has its
own lock and thus no need to hold global lock while accessing
scan database.
Also cleanup unused csr scan functions.
Change-Id: I7ad5a61e69c200f9dee6b9158c4d27708fdc98dc
CRs-Fixed: 3160360
Remove the redundant structures and operations in CSR module
for the stop bss request/response processing to/from SAP/NDI
modules.
Change-Id: I0db36caa509699fe5e0e9709d3e3689e551aad4f
CRs-Fixed: 3148791
Remove the usage of redundant legacy structures in CSR/SAP
modules and simplify the channel change request flow from
the SAP module to LIM.
Similarly change the channel change flow for monitor mode.
Change-Id: Ib91f65307d456919f68892f45f3aa9b4fed0f0d3
CRs-Fixed: 3148761
Remove redundant structures and APIs in the start bss response
flow for SAP and simplify the processing.
Change-Id: Ic346484200baec59d154c2c24d01fab0279647ed
CRs-Fixed: 3142915
Remove redundant structures and operations in SME/CSR.
Currently, start bss request is prepared in CSR module using
csr_roam_profile, which is built from sap context.
To remove redundencies, prepare the start bss request in SAP
module and serialize the start bss request.
Change-Id: Icd468fe2a48d5324c1485d83b05e27400c9dbd9a
CRs-Fixed: 3142912
Reduce the log level for the frequent acceptable errors
to reduce the roam latencies.
Change-Id: I9f5405025948d160e6fcd65ecca05dce7670ea84
CRs-Fixed: 3150439
Move MLO STA-SAP concurreny handling to Policy Mgr which
is present in CSR currently.
Also, Move MLO STA-STA concurreny handling to Policy Mgr
which was part of If Mgr currently.
Change-Id: I2b8de17c3d31b43ff1f6b81a7de07b88888d7fb5
CRs-Fixed: 3153393
Rename files with blacklist/whitelist to denylist/whitelist.
Rename files with blm to dlm.
Change-Id: Ief7ce0a797f74460c9708f8d2dd440412af5b7eb
CRs-Fixed: 3099864
If the connection manager command is moved from pending to active
queue after an SME initiated active command e.g SAP peer
disconnect, it's already holding the SME lock and trying to
acquire the connection manager lock.
Now if in another thread, the connection manager process is
already in progress and tries to get the SME lock,
the driver ends up in a deadlock.
Thus remove the SME global lock from the APIs called from
HDD disconnect handlers.
Change-Id: Ia1e9d4480935cb8954eeb02bf3d845dce4b29f8f
CRs-Fixed: 3139097
Remove ACM prints from sme_qos_is_acm function
as mask value in sme_qos_get_acm_mask indicates the same
Change-Id: I7c5e9f4cca78fc7a99459f7662184670371a6313
CRs-Fixed: 3134776
Remove redundant structures in CSR for SAP functionality
and add a new flow to post SAP requests from SAP module to
LIM.
Change-Id: If3339cf138140ea148bbd263960907fb3a01de43
CRs-Fixed: 3123072
Instead of print each frequency in separate line,
print all the frequencies in one shot in
csr_save_to_channel_power2_g_5_g.
Change-Id: I9bca0a94b702626e247bd63f3aa3a617597351a0
CRs-Fixed: 3128543
Before MLO sta partner link is up, FW can't indicate CSA event to host.
For this case, host need save csa parameters and process it when MLO
sta partner link is up.
Change-Id: I543c5e1069af5b1e88c6619364a7a44330134d2c
CRs-Fixed: 3082437
Add support for below EasyMesh specific commands
1. To set user specified channels in the acs channel list
2. To trigger ACS
3. To get the ACS report
Change-Id: I1090b9a86d62eddc9954b70835c7496e5a614757
CRs-Fixed: 3080222
TWT initialisation will fail for each non 11ax connection
so an error log is not needed if peer object for TWT is not found.
Also, RIC data is not mandatory in FT session, so if its not
present, log a debug level print instead of error level.
Change-Id: I7fec9f88aa68b2ae947e34a1aede311e9fed2d05
CRs-Fixed: 3117535
When WLAN_FEATURE_DYNAMIC_MAC_ADDR_UPDATE enabled and user space sets
mac address, host will detach vdev and attach again without setting
vdev tx data callback. Then host tx TDLS discovery request timeout
since lim_mgmt_tdls_tx_complete isn't called, finally TDLS link
establish failed. This change set vdev tx data callback after dp vdev
detach and attach done.
Change-Id: Iada58ba2df0612a92503ccfa5f246f7cca9db9ad
CRs-Fixed: 3112831
Intersecting EHT beamforming configuration from ini and FW
indication, then save it to eht caps of mlme.
For sta, update mlme EHT beamforming configuration to FW
through WMI_VDEV_PARAM_SET_EHT_MU_MODE directly.
For ap, intersecting mlme EHT beamforming configuration and user
configuration, then send result to FW.
Change-Id: I3d6185896af9fc58eb1fb6db913d4a425f72c696
CRs-Fixed: 3113235
Cleanup csr_get_cfg_dot11_mode_from_csr_phy_mode API by removing
unused parameters and use vdev id instead of profile.
Change-Id: Id2c8b52845d5e928e315b3af0a3d1289e81b2e7e
CRs-Fixed: 3113395
Remove unwanted parameters from start_bss_req and use
the parameters from vdev instead.
Change-Id: Ifea96bf7908b0dae66807b7a346684fe46fdcd4e
CRs-Fixed: 3105488
CAC duration of new channel should be able to get before CSA. During
CSA, CAC duration of new channel is used to populate max channel
switch IE.
Change-Id: I25d430d3eb663c90555ebad7a214b0789ea8c1ce
CRs-Fixed: 3102581
Currently when ever there is a change in MLD MAC address, MLO manager is
not being notified with new MAC address. This resulting in memory leak
for mlo dev context which is created with old MLD address.
To address this, update MLD address in MLO manager with new MLD address.
Change-Id: I1a3eb9426dc39e5b4fe5bfaf0bd4a571280eb50c
CRs-Fixed: 3103077
A MLO with 1 link not active will lead to HW mode as SMM instead
of SBS, so check and see if SBS MLO is present and take
decision as per it.
Change-Id: Ide487d56d6375892b91ab615b9ad314dba2c9991
CRs-Fixed: 3102349
Currently in SAP mode, when host driver receives disconnect for
station, first it gets disconnect stats with serialization command
and then it sends delete peer command to fw. There is an issue with
this approach, if there are maximum number of clients are connected
to a SAP and all of these clients gets disconnected at the same
time, in that case there will be a disconnect stats command and
peer delete command in serialization, because of which serialization
queue gets full.
To address this issue, remove disconnect stats command from
serialization and send this command just before sending peer
delete command once peer delete command gets serialized.
Change-Id: I2fa1a5a393939eebbce796e11348fa7c040b40e8
CRs-Fixed: 3100914
Currently, MAC address update is supported only when interface is down.
Because of this framework needs to issue interface down and interface
up to update the MAC address. Interface down and up will lead to VDEV
delete and VDEV create commands to the FW.
To optimize Host-FW interactions during set MAC address, add support
to update the MAC address without bringing the interface to down state.
Change-Id: I76afa8f8c2504e8271bf689392d526f994afff0a
CRs-Fixed: 3063201
Max channel switch IE is getting enabled through the ini config.
This is getting lost while copying the phy_config.
As there is no additional target support required for enabling
this IE, retain the config received through ini.
Change-Id: Ic200d8e92346e6c3fba2bca9f1776aee2b106ae4
CRs-Fixed: 3086447
Handle SAP + MLO_STA concurrency after MLO connect, by disabling
one of the SBS link if 2.4Ghz SAP is present.
Also if roam happen to non SBS MLO remove the disable restriction
of MLO.
Change-Id: I7d9503a01bb23cd06808b46c090f0dee39c96af6
CRs-Fixed: 3096310
Handle SAP and MLO STA concurrency such as:
1) If MLO STA is present with both links
in 5/6 Ghz then SAP comes up on 2.4 Ghz,
then Disable one of the links.
2) If there is channel switch for sap from
2.4 ghz to 5 ghz, then enable both the
links as they were disabled by previous
operations when sap was on 2.4 ghz.
3) If MLO STA is present with both links in
5/6 Ghz and SAP, which was present on
2.4 ghz, stops then renable both the as
one of the links were disabled because
of sap on 2.4 ghz.
Also, in case where MLO STA roamed from
5 + 6 link to 2.4 + 5/6 link force scc
will happen and the disabled link has
to be enabled.
Both links should only be enabled if mlo
sta has more than one links.
Change-Id: I0fd0093b20336ae32325981589c399b44a44b64e
CRs-Fixed: 3092202
Currently there is no provision to get the calibration failure
information from the driver. Because of this it is getting difficult
to debug the calibration failure issues.
To simplify the calibration failure issue debugging, add support to
parse calibration failures events in the driver.
Change-Id: I6d831804cca259862fea3e8bb4af33d556138d43
CRs-Fixed: 3078926
Update the 2G and 5G HE capabilities with user configuration
to advertise the user configured HE MCS in management frames.
Change-Id: I59952aba0187cd169be518336c69aa93b512327b
CRs-Fixed: 3074827
This change gathers the roam event stats from the FW.
New vendor event is used to fill in the vendor attributes
whenever the roam stats are received from Firmware.
Change-Id: I9a2ddef62d26b0b68897891788733df452ac1ceb
CRs-Fixed: 3036518
Based on the new NCHO requirement, allow ADDROAMSCANFREQUENCIES to add
roam scan frequencies irrespective of the roam scan control value.
Change-Id: I5742f6d590e3ec51bfb294610ede05b1935a4790
CRs-Fixed: 3046763
Currently, failure in csr_roam_synch_cb is not handled, therefore
failure during roam sync indication processing in CSR, leads to
out-of-sync between LIM and CSR sessions.
Handle the failure in csr_roam_synch_cb, by aborting the
roam complete notification to FW, and then process HO failure from
FW to cleanup LIM and CSR which will hold different BSSID profile.
Use vdev id instead of BSSID to retrieve/delete the LIM session.
Change-Id: I5ff2280e7ba1a8cb8e44c0c6b70647bf12b6ef31
CRs-Fixed: 3046370
Currently, southbound MLO disconnects are not handled properly because
the partner link is not being disconnected. To fix this, update
current calls to cm_disconnect to use mlo_disconnect instead, because it
can handle both legacy and MLO disconnections.
Change-Id: If908e2391290fd4a328f3d7d213c5ef6c1f5452c
CRs-fixed: 3029864
There are duplicate macros for the same purpose, hence
replace WLAN_ALL_SESSIONS_DIALOG_ID with TWT_ALL_SESSIONS_DIALOG_ID.
Change-Id: I63130869eed8dffcce85fe6a04586592ab3eaca2
CRs-Fixed: 3047686
During wma_pdev_hw_mode_transition_evt_handler()
get the freq range from mac_freq_mapping[] present in
wmi_pdev_hw_mode_transition_event_fixed_param and pass
till policy_mgr_hw_mode_transition_cb() and update
cur_mac_freq_range[MAX_MAC] from it. if no freq range
provided (legacy chipsets) then use
freq_range_caps[MODE_HW_MAX][MAX_MAC] to fill the
range depending on the new HW mode.
Change-Id: I145d48052ce37724b0f697c19a1041f5a908cb54
CRs-Fixed: 3044976
PMK stale entry will be updated in driver by framework after
disconnection with AP. Since there is no connected profile
in driver no MDID is associated. On new PMKSA addition in
driver it will check for cached entry based on MDID and
remove older one. This commit associates MDID to the cache
entry from the scan result if no connected profile is
present.
Change-Id: I9e8362387a53f622b9c52c4ba994939cabf244aa
CRs-Fixed: 3030376
If SAE/H2E required by hostapd configure, it must populate in
supported rate or extended support rate set, add host driver support
to check this flag and populate it in extended support rate set.
Change-Id: Id75b5743e93a1a0f1d13150d5436d256e2ca117c
CRs-Fixed: 3016492
ARP response dropped at OSIF due to non-availability
of sta entry with MLD address.
Added sta entry in OSIF/HDD context with MLD address.
Change-Id: Iff70197ca5707b88ea80b42a60a2b1fb383f00a9
CRs-Fixed: 3017249
