Currently the TDLS component code is unconditionally built which will
bloat images where TDLS is not required. Fix this by only building the
TDLS component when the TDLS feature is enabled.
Change-Id: I7496b8f07ed495b00e62fc3cf50a96e1829d9341
CRs-Fixed: 2399966
As part of the TDLS feature, structs sta_uapsd_trig_params and
sta_uapsd_params were replicated from qcacmn wmi_unified_param.h to
qcacld-3.0 wlan_tdls_public_structs.h, and conditional compilation
based upon CONVERGED_TDLS_ENABLE was used to determine which structs
are actually used by a build. Since these structs are not specific to
TDLS, remove the duplicates and exclusive use the structs from qcacmn
wmi_unified_param.h.
This is co-dependent upon Ida0f2b6f131ff2dce7217b881ffadecfd685f563
("qcacmn: Remove TDLS featurization from UAPSD trigger structs").
Change-Id: I37b2d80a4710aced158dcf2ea973d15801a7cecc
CRs-Fixed: 2395823
Enumeration TDLS_PEER_STATE_CONNCTED contains a spelling error, so
rename it to TDLS_PEER_STATE_CONNECTED.
Change-Id: Ifa0ff667a407cdad3e240aec6c188f20336a166a
CRs-Fixed: 2397350
Add the WMM config ini config
CFG_TL_DELAYED_TRGR_FRM_INT_NAME to MLME cfg.
Introduce the basic infra APIs related to these configs
from mlme.
Change-Id: Ifaf8072a78f21760e00973e625d7c8e41d8b51a6
CRs-Fixed: 2361533
Currently many modules use the scheduler_post_msg API which
doesn't allow the driver to know about the src, and destination
modules.
Fix is to call scheduler_post_message which has src, dest, and
the que id.
Change-Id: Ia5c43fe3ceeb7db9dde6241cbabac0ce48f88061
As part of connection tracker handler, If the link is connected
then current tx and rx stats are compared with configured threshold
values. If the current stats fall below the threshold then idle timer
is initialized and idle peer data is stored in tdls soc and given as
userdata to the timer handler. The userdata is overwritten if the another
tdls peer becomes idle and this can lead to wrong tdls peer teardown.
Change-Id: I34638bdebe02e17e1c9e117e58352bdaab867921
CRs-Fixed: 2393320
Currently, in tdls soc max tdls peers are initialized
in tdls_global_init that is done as part of tdls psoc open.
But, sometimes the Ini values used to initialize the tdls
max peers are not initialized before global init
because tdls_update_config has done for the Ini vallues.
This can lead to wrong value of max tdls peers in tdls
soc and later can result in TDLS connection deny.
Change-Id: I6bb51db571129490c225737c1913b8ddafadde8d
CRs-Fixed: 2392494
Refactor firmware, serialization and command timeouts so that
HDD timeout are greater than serialization is greater than firmware
timeout.
The timeouts are defined considering below worst case delay in
firmware.
WMI_VDEV_START_REQUEST_CMDID 6 sec
WMI_VDEV_RESTART_REQUEST_CMDID 6 sec
WMI_VDEV_STOP_CMDID 2 sec
WMI_PEER_DELETE_CMDID 2 sec
WMI_PEER_ASSOC_CMDID 2 sec
WMI_PDEV_SET_HW_MODE_CMDID 2 sec
WMI_PDEV_SET_MAC_CONFIG_CMDID 2 sec
Change-Id: I270e980ed1cf2aee55a1fa4e88ff8ddc845a203b
CRs-Fixed: 2384389
Fix implicit tdls connection issue. Correct usage of qdf_mem_set.
DUT could receive multicast frames after tdls connection tear down,
add check condition of frames with multicast dest address in
tdls_update_rx_pkt_cnt.
Change-Id: Ia1d7bbf2c129e9aebc98f7fcdea263b745c221ec
CRs-Fixed: 2375043
It alloc memory with structures in sir_api.h, and process/parse them
with structures in tdls component, which will cause memory corruption
potentially. So, this change refacor these functions and let them use
unified structures. Remove unused structures in sir_api.h
Here are these functions:
- lim_send_sme_tdls_add_sta_rsp
- lim_send_tdls_comp_mgmt_rsp
- lim_send_sme_tdls_del_sta_rsp
- lim_send_sme_mgmt_tx_completion
Remove below unused tdls structures:
- tSirTdlsDelAllPeerInd
- tSirTdlsDelStaInd
- tSirTdlsEventnotify
- tSirTdlsLinkEstablishReq
- tSirTdlsLinkEstablishReqRsp
- tSirTdlsAddStaRsp
- tSirTdlsDelStaRsp
- tSirMgmtTxCompletionInd
Change-Id: Ic595cadefcdbeb2df44f97563c4652db409213a2
CRs-Fixed: 2373706
TDLS component related files moved from hostcmn to CLD, this change
adds initial functions, enables TDLS in Kbuild.
Change-Id: Ie5b93f4785c4a973a139dff9e58460fd7ee35e35
CRs-Fixed: 2361589
This is mirror change for 0f9f01950
Currently if the number of APs in the STA environment
are many, then the STA will receive many beacons, whose
beacon process path can take long time, in the kernel
work queue, hence the other processes have to wait
for them to complete, and may get timeout, if the
the time to process the beaocns is larger than their
process timeout.
Fix is to :-
1. Add rate limit to failure conditions of memory
not allocated
2. Make memory allocation in path of beacon process
atomic.
Change-Id: I488b446c23fd01c993f7dd9bd989867fda2331d8
CRs-Fixed: 2363307
