Add extract_roam_stats_event to wmi_ops to allow cld driver to register
the corresponding callback.
Change-Id: I77ebb05a1a2ce9fa0b2f2f2ffb50c523ab9070e6
CRs-Fixed: 3007690
WMI_MGMT_RX_REO_FILTER_CONFIGURATION_CMD is used to the configure re-order
criterion for incoming management frames. Add WMI layer support for the
same command.
Change-Id: If1498fd4fbccd86e7d54d9eac268868b36523d06
CRs-Fixed: 2960472
When MGMT Rx REO feature is enabled, FW will be sending MGMT Rx REO
parameters TLV as part of WMI_MGMT_RX_EVENTID for the frames that require
reordering. Add APIs to extract the same.
Change-Id: I57b132927cf413384d680b5778bfe6a2e2737adf
CRs-Fixed: 2960471
When MGMT frames are consumed by the FW, FW sends MGMT Rx FW consumed event
to the Host. Add WMI layer functionality for this event handling.
Change-Id: Id95f41a717b88589e861781e1111b17dc90475be
CRs-Fixed: 2959118
In the WMI_MGMT_RX_EVENTID event handling, add a length
check to validate if the buffer length sent by the firmware
is less than or equal to the actual buffer length.
Change-Id: I7db9af48bc525543b972dcaf40aee0a05d8f5023
CRs-Fixed: 3001331
In the WMI_PDEV_FIPS_EVENTID event handling, add a length
check to validate if the buffer length sent by the firmware
in fixed params is less than or equal to the actual buffer
length before processing the data.
Change-Id: I7a952d3e3a2f66060451263b72118a52aa89dd06
CRs-Fixed: 3009887
With latest architecture there are different HTT peer
data versions supported by the firmware, supported htt peer
version will be sent in the service ready and need to feedback
to the firmware in the init command.
Change-Id: Icd0470843198387cd7e0192cbe3821d45ef0534e
CRs-Fixed: 3008706
Add length sanity check for ibf cal value & phase delta
to ensure HOST always align with target defined length.
Also remove the REPORT_AOA_FOR_RCC flag usage.
Change-Id: I06e4a430143df1534849b8ec974e38932cff3ef1
CRs-Fixed: 2997030
Add new field ema_init_config to signal the configured value of
beacon size while using MBSSID feature in 6Ghz.
The current allowed range is 1500-3500 bytes.
CRs-fixed: 3004041
Change-Id: Id8cc1b7e4602b2e52b8eb215337070c6e3c26089
Add P2P_P2P_CONCURRENCY_SUPPORT service capablity to
validate whether fw can support p2p concurrency
support or not. when firmware advertises this flag it
can support MCC,SCC, DBS for p2p-GO/GC + p2p-GO/GC.
Change-Id: Ifec4bf984595b06374be9024601733c8537a9c3e
CRs-Fixed: 2984165
Add a function pointer to a function that converts host vdev param to FW
vdev param.
Change-Id: I01557d8bd87cb82548114626ff726aabba01dd19
CRs-Fixed: 3005160
Add debug prints when parsing the EXT chan list update event to dump the
reg rules received. The regulatory info is often updated and new bugs
are introduced every time so the prints will help narrow down the issue.
Change-Id: I229fa2e1432786c9a530f3a6035926135b2c4e2f
CRs-fixed: 3001297
Add storage for EHT mac and phy capabilities as
per 11be D1.0 and update the EHT mac and phy capability
sizes.
Change-Id: I67224b35b701235374772e9975375e695f3ed959
CRs-Fixed: 3000166
A new TLV is added to send partner link CSA/ECSA count offset to FW as
part of beacon template. Add WMI changes to populate these TLVs in the
beacon template send function.
To fix the compilation issue, added forward declaration of 'struct
vdev_mlme_obj' and removed 'include/wlan_vdev_mlme.h' include file from
wlan_mlo_mgr_public_structs.h.
Change-Id: I6e421b29bb887bec711a23db1458aca4d112ade4
CRs-Fixed: 2983249
In WMI INIT, check whether firmware supports the ack event or
not. If it supports then enable driver support and send it to
firmware during WMI INIT.
Change-Id: Icfdee6bc06e6a393de880b87fdab70665ea7c8b4
CRs-Fixed: 2987898
In case if TWT command (i.e setup, terminate, pause, resume,
nudge) comes from userspace and if the firmware is in below mode
1. scan in progress
2. roam in progress
3. CSA is in progress or
4. Any other error
then the command needs to be rejected in userspace context.
Synchronize the TWT command so that whenever command goes from
driver to firmware, then driver will receive ack event first
followed by respective event (i.e add dialog, delete dialog,
pause, resume, nudge) with below condition
1. If driver receives the ack event as successful then driver
waits for this ack event, respective event with status of the
TWT action frame over the air is expected.
2. If driver receives the ack event as failure then it will
rejects the TWT command in userspace context.
Change-Id: Ie885d98ecf2dad98d34676d889fd70e4c84f0a05
CRs-Fixed: 2987904
Add API to extract AoA phase delta and IbfCalValues from
WMI event. Also Add service bit to support the feature
Change-Id: I6f6514711345dd47c4be3673b8c40501feb763e9
Check the below service bits and set in psoc if the service is supported
by FW.
WMI_SERVICE_RTT_AP_INITIATOR_STAGGERED_MODE_SUPPORTED
WMI_SERVICE_RTT_AP_INITIATOR_BURSTED_MODE_SUPPORTED
Change-Id: I13504958bf31b2d645d915b4db20719bdc9a4133
CRs-Fixed: 2969195
Add WMI support for EHT puncturing by filling puncture
bitmap in vdev start and peer assoc commands.
Change-Id: If1d2541655558f22a96a741999ec4ff7348f695a
CRs-Fixed: 2982498
In the current implementation, csa_event_bitmap for CSA in the beacon
template WMI command is set to 0. Hence, the FW sends CSA complete event
to the host at the end of CSA complete.
Set the below values to csa_event_bitmap to get the current channel switch
count from FW to update the CSA/ECSA IE count in probe response frame.
1. WMI_CSA_EVENT_BMAP_ALL:
To get the CSA switch count event for every update to switch count.
2. WMI_CSA_EVENT_BMAP_SWITCH_COUNT_ZERO:
To get the CSA complete event only when the switch count becomes zero.
3. WMI_CSA_EVENT_BMAP_VALID_MASK:
FW to follow the bitmap for sending the CSA switch count event to the
host. Example,
0X80000000: Send the CSA event when the switch count becomes zero.
0X80000033: Send the CSA switch count to host for the count 0,1,4 and 5.
Change-Id: I8380d6badc3b84c72fde489e59b51b5ac122b97b
CRs-Fixed: 2978799
TLV targets support updating tx chainmask(soft-set) using
PDEV_PARAM_TX_CHAINMASK param. Update host enum accordingly to
use this for setting soft chainmask.
Change-Id: Ic5362fb8c79f07cbd83328b786b5930f75d2a084
CRs-Fixed: 2976914
First Requirement:
In case of WTC_BTM roam trigger reason, if FW reports rssi
threshold for 5G and 6G AP via wmi_roam_trigger_reason,
Host should print it in kmsg.
If wtc_candi_rssi_ext_present is set (1), It means fw
reports 5g and 6g candidate rssi (new firmware case).
If wtc_candi_rssi_ext_present is clear (0), It means fw
doesn’t report 5g and 6g candidate rssi (old firmware case).
Host use flag "wtc_candi_rssi_ext_present" to keep backward
compatibility.
Second requirement:
As per user space, value for scan mode in WTC command, is
like below:
0: no Scan, 1: partial scan and 2: full scan.
For NO scan case, FW sends value
ROAM_TRIGGER_SCAN_MODE_NO_SCAN_DISCONNECTION (3)
in wmi_roam_trigger_reason-> wtc_scan_mode. When driver receives
WTC scan mode as ROAM_TRIGGER_SCAN_MODE_NO_SCAN_DISCONNECTION,
it should print value as 0 instead of 3.
Convert WTC scan mode comes from FW to
wmi_configure_roam_trigger_parameters->scan_mode to make it
compatible to WTC command.
Change-Id: I8266460aac1272d345e4349c2ca52b4f9a745d4c
CRs-Fixed: 2965362
For some platform, ext2 service bitmap is not supported. So rate
limit the wmi ext2 service bitmap NULL error log to avoid
excessive console logging.
Change-Id: I383632669e4e4a59dd9e6e3ce82626a7cd3e42b3
CRs-Fixed: 2949180
Add functions to parse and extract wmi smart monitor
event received from target.
Change-Id: Ic18e3134b684c5f8e12839e997d628909a7e27c9
CRs-Fixed: 2969247
Currently the 6G edge channel feature is MCC specific.
Make the 6G edge channel feature common for WIN and MCC.
Change-Id: I723b6db1d74dca5a911eede4ec6e6167f6b3e6bc
CRs-Fixed: 2976871
New TLVs for MLO flags are introduced in peer assoc WMI
command. Add WMI changes to add these TLV in the peer assoc
command.
Change-Id: I366a96c973c3bedda03e4c370099ff809e0bd83d
CRs-Fixed: 2958851
New TLVs for MLO flags are introduced in peer create WMI
command. Add WMI changes to add these TLV in the peer create
command.
Change-Id: I38a129b30b366b6e3939231699f210d1bac362a1
CRs-Fixed: 2958849
Add parameter 'bool sync' for wlan_cfg80211_crypto_add_key()
to indicate whether or not to add key synchronously.
If it's set to true, wait until install key complete event
is received.
Change-Id: I9a69d486665fb3f65a5720ccfbfb638c09329418
CRs-Fixed: 2865832
Current FW implementation is not expecting MLO and partner link params
in vdev restart request. But host is sending these params as part of
vdev restart request. This is resulting in TLV count mismatch for vdev
restart request.
To resolve this, Don't send MLO and partner link params in vdev
restart request command.
Change-Id: Ied4572722c701ad7f53ac12727228a383e570433
CRs-Fixed: 2973256
New TLVs for MLO flags and partner link info are introduced in vdev
start WMI command. Add WMI changes to add these TLV in the vdev start
command.
Change-Id: Ic7d54c406f69346a6eedb43b1ebcf7266c448bd8
CRs-Fixed: 2958843
WMI vdev create is changed to incude mlo macdress as one of TLV.
Add changes in WMI vdev create send API to include this new TLV.
Change-Id: Ia13bdb8fbfc9f68d1e4c0209201f9acc4f575387
CRs-Fixed: 2958839
802.11BE D1.0 9.4.2.295c.4 Supported EHT-MCS And NSS Set
field specifies maximum 4 optional EHT MCS map, which are
20 MHz-Only STA, BW <= 80 MHz except 20 MHz-Only STA,
BW = 160MHz and BW = 320 MHz.
Therefore set WMI_HOST_MAX_EHT_RATE_SET to 4.
Also add a debug message to log peer_flags_ext.
Change-Id: I3d56998bf0de381ef147d6c0551dcdb7fd935f60
CRs-Fixed: 2963536
Set the SAE EAPOL offload support in resource config based on
WMI_SERVICE_SAE_EAPOL_OFFLOAD_SUPPORT bit received in service
bitmap from Firmware.
Change-Id: I878736105c070df514dfe8d989541227b3baad11
CRs-Fixed: 2957082
Add a new flag to indicate to fw that host will set the
nan_disable_flag for channels.
Change-Id: Ibf627bff77e1afb0849149a63981ca50476f6bfd
CRs-Fixed: 2949481
