Remove makefile for Rouleur codec.
Remove usage of shell command and update absolute path cmd
for AUDIO_ROOT.
Change-Id: I1589c688639892b7628914a3777632466949d000
Signed-off-by: Meng Wang <mengw@codeaurora.org>
Add enum names defined for callback between wcd and bolero in
separate file and include that file in order to have same enum
across wcd and bolero.
Change-Id: I808c2ad3de37655c1ba2b8e096def60703ced7f2
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Configure low PA Gain for low state of charge based on dt node.
Change-Id: I7f36cf4b17d9794a2763edc3c2fd5cec53a3521f
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Impedance values are not correct sometimes due to ramp
being controlled by hw. Run detection routine for sometime
and take final value as impedance value to resolve issue.
Change-Id: I3a34813657751aa304e150cfa294a42f556d06c4
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Rouleur has different hph settings for different foundry
id. Read foundry id and update hph settings so as to
provide same settings to end user.
Change-Id: I114047226462ab95e0c93271c3d6099f15af2343
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Register to power supply framework to get soc capacity.
Reduce ear and hph gain for reduced voltage to optimize
power consumption. Also set LD22 voltage to lower value
for low SoC.
Change-Id: I94de9341b8c7307128d3cd41c7398c31d57fa685
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Update the EAR and LO power up and down sequences to
fix CnP issues in rouleur codec.
Change-Id: I7e6d1cc82e9c1358b336c32b1befb7eb1dd9b552
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Make dev_up true before giving 500 ms delay in case of AATC
variant during BOLERO_WCD_EVT_SSR_UP event.
Change-Id: Ie8306c92a80df69f087f055d425b22f48f319873
Signed-off-by: Faiz Nabi Kuchay <fkuchay@codeaurora.org>
Aux cable is detected as unsupported sometimes due to it being
detected as cross conn. Increase hph cross conn threshold to 350mV
so that it detects fine.
Change-Id: I87e4bd36f80d7cd62e06c76acf9c9d06bb6f148a
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Add delay in post ssr to eliminate playback pause on euro usbc headset.
Post ssr, headset is detected as headphone as HPH PA gets turned ON
before the completion of wcd_correct_swch_plug workqueue in MBHC.
Change-Id: Ib0334b37aa12b7e7371146b26eb3a1f4484656a3
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
HPH PA pull down control is set to force ON instead of auto
due of which saturation/noise is observed in headset
playback at highest volumes. Set pull down control
to Auto to fix this issue.
Change-Id: I465588f46b04bbb32d84f76b8b5bedd2ef21bd2a
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
When current source mode is enabled, comparator auto
zeroing should be turned ON by HW. As rouleur codec HW
doesn't do this automatically, add this support
in SW to set the auto zero enable before FSM enable
and reset to auto once FSM is enabled.
Disable surge protection before ADC measurements
and change HPHL and HPHR thresholds while
identifying cross connection for proper
accessory identification.
Change-Id: Ib775de0f0bdb6c655a3c0eb4775276acfbca1e84
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Current source mode in rouleur does not work
properly leading to issues in button interrupts
and fake electrical removal interrupts.
Enable pull up mode instead of current source
mode to fix these issues. Modify the headset
max vref voltage to 1.7 volts and micbias
calculation logic.
Change-Id: If3e4a2fdcf080b07fe3c363b6eb6115f101b91f4
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
For power saving during RBSC, need to vote for minimum
or zero current on load for respective regulator to
enter LPM mode. Add required support from rouleur
to vote for mic bias accordingly during suspend/resume.
Change-Id: Idb2accbc77241e19f688225081e1b68b99c19e29
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Update PDM watchdog interrupt sequence for rouleur
codec. Add HPH PA gain registers in regmap and update
defaults. Update mic bias register bits and rouleur
version for ADIE RTC to work.
Change-Id: I1bbb41efcdd9a0a8b38fcd4beadbd5d639a4b858
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Micbias value set does not take effect on rouleur.
Shift micbias value to correct bits.
Change-Id: Ice083e3bc30f6e8e3fe7132c633a4043329ccfa5
Signed-off-by: Xiaojun Sang <xsang@codeaurora.org>
Update HPHL and HPHR sequence to avoid clicks and pops
by setting the LDIV and RDIV values in HD2
coefficients and increasing ramp time.
Change-Id: Ib47d14255a098511393b4b75392854c8b34dc0d3
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Add rouleur codec support in bengal machine driver
to create codec entry and invoke mbhc hs detect
functions for respective codecs. Correct the logic
for headset detection pull up current and
volatile registers for digital part of rouleur codec.
Change-Id: I22545dc796c215c1501e883796546c97d8ca8698
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
