Add changes to send roam scan mode over RSO start/stop/update_cfg
from connection manager. Update the roaming params and roam scan
params to new structure.
Refine send_roam_scan_offload_mode_cmd_tlv().
Change-Id: I6adce2e8a24ece93a079032d0e66760393fcdccd
CRs-Fixed: 2766023
In some instances, AP does not respond to probe req
causing join timeout at STA and no connection.
To solve this,send multiple probe requests(every 200ms)
to AP until join failure timeout(1 sec) expiry,
if single bssid case retry same bss again
(configurable via ini, max allowed tries 2).
Change-Id: I7a7eeedcc24db1a74cd186ff957c638a39cdea6d
CRs-Fixed: 2763815
Currently the driver enables the SRD channels
support for both P2P_GO and SAP if the SRD master
mode is enabled.
Have individual ini values to enable/disable
the SRD channel for each op-mode as required.
Change-Id: If6e66996ed19dacbde7f71a6702f378a7e9a273c
CRs-Fixed: 2748446
The ini ratemask_type and ratemask_set can be used to limit
the maximum phy rate. The ratemask_type is used to select
the phy mode and the ratemask_set to select desired NSS and MCS.
It can be used to optimize link performance.
Change-Id: Ia5c9f3a80eb93710bdcf53dabc4a45e554753b01
CRs-Fixed: 2758859
Add user configuration support to configure dot11 modes for
different vdev types.
Change-Id: I338d9d76f000195d1798bbc8b3b7ff1fb33ee305
CRs-Fixed: 2760240
If join fail reason is timeout, retry sending join req
after timer expiry, timer value can be configured
via join_failure_retry_interval.
Change-Id: If90071b3f6d7f48936db6f7088c3c1547e48b294
CRs-Fixed: 2760236
Add changes to define structure to hold the WMI_ROAM_SCAN_MODE
command related parameters.
Also added minor cleanup changes.
Change-Id: I24ef18e05de8dd05ee437e440651ea9ab0731e46
CRs-Fixed: 2758316
Add support to retry the deauth frame if the Tx is not success if
user configured the retry count.
Change-Id: Id128b4a70a276ee86270372ff7954e40bde8123c
CRs-Fixed: 2754305
Host sends the WLAN_MSG_WLAN_STATUS_IND to WiFi Location Service(WLS) via
cnss daemon which includes supported channels. WLS service is yet not 6GHz
capable. Hence to limit the 2.4GHz/5GHz channels only in
WLAN_MSG_WLAN_STATUS_IND introduce new INI "wls_6ghz_capable".
Change-Id: I77b284d2025601fec72aa35d430f18865f15f247
CRs-Fixed: 2748489
Currently driver sets the NOL state of the channels to false
on every regulatory updated, which indicates the channel is
not in NOL. Which may lead to some issues where the channel
is actually in NOL but host treats it as non-NOL channel.
Ideally NOL list should be maintained throughout the driver
lifetime and across the regulatory changes.
To address this issue add a logic to not update the NOL state
of the channels whenever the regulatory update is received.
CRs-Fixed: 2744916
Change-Id: If96b22ab29a60a2aa752bbf01aaae46fc37362eb
Add connection manager changes to send roam scan offload init
deinit. Add new enum roam_offload_init_flags to fill the roam
init/deinit flags, 4-way handshake offload, bmiss skip full scan
flags at connection manager instead of getting the ini and filling
at target if.
Change-Id: I558e868efd341b508d3df76c8d6ab90eac512432
CRs-Fixed: 2745585
In current implementation, vdev create command is sent to the FW from
vdevmgr_mlme_ext_post_hdl_create. By design vdev create command should
be sent to the firmware from vdevmgr_mlme_ext_hdl_create.
To align with the design, send vdev create command from
vdevmgr_mlme_ext_hdl_create.
Change-Id: I42203ae5c4f75388e520e7fc3bd9114dd3236492
CRs-Fixed: 2714533
Check the required security types allowed for 6GHz connection and
do not allow the connection if the secutiry check fails.
Change-Id: Ic680c4600b3f17151e42f8708ff8810e5d16e52e
CRs-Fixed: 2715086
Add new channel 177 to wiphy struct ieee80211_channel
hdd_etsi13_srd_ch and rename the struct to
hdd_5dot9_ghz_ch.
Add a new ini fcc_5dot9_ghz_chan_in_master_mode to
enable/disable new 5.9 GHz channels 169, 173 and 177
in master mode.
Change-Id: I68dc3be18277ca0e416a579327f406279458899e
CRs-Fixed: 2693707
The band_capability field is used in other places to be
a bitmap over reg_wifi_band. Update the field in wma_tgt_cfg and
wlan_mlme_generic to take the same bitmap for consistency.
Update all references to these fields to expect a bitmap as well.
Change-Id: I8abd697e2fbe02b4eadd32f3027bef7408bac2a0
CRs-fixed: 2726710
Introduce new INI sae_connect_retries to decide auth (initial connect
and roam auth) and connect retry for sae. MAX reties is capped to 2
and max for roam auth is 1.
Default is 0x49 i.e. 1 retry each.
Bits Retry Type
BIT[0:2] AUTH retries
BIT[3:5] Connection reties
BIT[6:8] ROAM AUTH retries
Change-Id: Idae86a7bdb32244c7f3a140b8591418b8238758a
CRs-Fixed: 2728458
Currently, function mlme_is_freq_present_in_list calculates
index based on chanel frequency in a loop of num_freq.
But acs_weight array can hold NUM_CHANNELS number of values.
loop index more than NUM_CHANNELS may lead to OOB read issue.
Fix is to add a validation for loop index < NUM_CHANNELS to
avoid any OOB issue.
Change-Id: I3c1d3393cd2a40147c325fea8f76b1db1a51f457
CRs-Fixed: 2727312
Rename the existing roam offload states to include
WLAN_ prefix. Add 2 new states:
WLAN_ROAMING_IN_PROG - Roaming has started at firmware, this is
after candidate selection at firmware.
WLAN_ROAM_SYNCH_IN_PROG - State after handoff is complete at
firmware.
Also move the roam_offload_state enum to connection manager.
Change-Id: Ib1f38d200393849253893113172cdfc69e381fb3
CRs-Fixed: 2725387
Send Vdev pcl command on both connected STA vdev when sta+sta
roaming is enabled. Handle below cases:
1. When 1st STA is connected send PDEV pcl command for the
first sta. Set pcl_vdev_cmd_active false.
2. When 2nd STA comes up, Set pcl_vdev_cmd_active to true,
send vdev PCL for 1st sta before enabling roaming(disabled
as part of the connect on 2nd STA).
3. For second STA force dbs connection when
enable_dual_sta_roam_offload ini is enabled. Set the channels
of the 1st connected STA band as invalid and remove these
channels from the scan filter.
4. On disconnection of 2nd STA connection, clear the vdev
PCL sent for 1st STA and then send PDEV pcl command.
Also make changes to send set PCL command after roam init
is done before RSO start is done at firmware to avoid assert.
Post set pcl command from sme/csr through lim/wma/wmi to avoid
the above condition.
Disable roaming on the vdev before sending set PCL command to
avoid roaming on undesirable band & channels.
Change-Id: I6bd869015b7248fe5c5c90b6e2fa0174995be197
CRs-Fixed: 2725360
Enable compilation of the connection manager roam files with
Kbuild changes.
Add new API to store and retrieve the firmware scan channels at
mlme. Also add initial support to post SET_PCL command through
lim, so that it is not sent before ROAM init command.
Add changes to restrict connection of the 2nd STA to
channels on the other band of the 1st STA connected band.
This is done by filling only the allowed band channels in
the scan filters for the 2nd STA connection. If only
1 STA is active, it is allowed to connect on any band.
Add header gaurds for missed header files:
wlan_cm_tgt_if_tx_api.h
target_if_cm_roam_offload.h
Change-Id: Id2bce12b9663ed635ea46164169b088461aab870
CRs-Fixed: 2720341
Host retransmits WPA3 SAE authentication frames after 1 second
if there is no response for previous auth frames from AP.
Host keep retransmitting SAE auth frames for max WLAN_SAE_AUTH_RETRY
times.
Change-Id: I1be0bd5354586518781876646b063592e667b0bb
CRs-Fixed: 2716719
Add new ini enable_dual_sta_roam_offload to enable/disable dual
sta romaing feature. Enabling this ini will allow firmware to
roam on both the vdev if firmware supports dual sta roaming and
the hw is dbs capable.
This ini will be checked in the dual sta roaming offload state
machine to enable roaming on both the STA or to fallback to the
current implementation where first connected sta will have rso
enabled.
Change-Id: I04f141ac31e0f168b6f19fe878bca219a36cfae7
CRs-Fixed: 2709036
Currently the driver supports the dynamic
configuration of nss and chain to FW for
VDEV if the FW advertises the capability
of supporting the same. However there is
no support to overide this.
Fix is to have an ini to enable/disable
this feature of configuring the dynamic
nss and chains to FW.
Change-Id: I0b84bb5aec53966a43a00c11d4aba3863414005c
CRs-Fixed: 2708303
Introduce an INI "oce_subnet_id_weightage" to indicate firmware
about oce subnet id weightage so that firmware can use subnet id
weightage to calculate candidate AP's score.
Change-Id: Iaf3be1947f8966a2e2c34162d251a31950058231
CRs-Fixed: 2674596
RMC is IBSS specific and CFG_RMC_ACTION_PERIOD_FREQUENCY is not used
now so remove the same
Change-Id: Icafff4bd7eb508d92c383861300146e3a0f2def7
CRs-Fixed: 2689882
With specific AP(s), FW needs to perform FT initial mobility
association instead of FT roaming for deauth roam trigger.
This ini is used to configure "FT roaming for deauth roam trigger"
behavior from the HOST.
Change-Id: Id754a21f7ac2c330019055646f79c79db3e0c52c
CRs-Fixed: 2665882
Remove instances of CFG_COUNTRY_CODE and country_code from
wlan_mlme_reg struct.
Remove redundant country code APIs.
This change is needed because the country code is no longer
stored in CFG file, and subsequently, there is no need for
CFG_COUNTRY_CODE.
Change-Id: Ia4b3b40d0dccfde696352967f2902dfba344a445
CRs-Fixed: 2634079
Add support to provide the channel weightage of
DFS channels so that the weight can be configured
and the user can control whether they are allowed
to be selected for the SAP.
Change-Id: I53a22a0059d56aa8fca66215fed1ed0588db7db5
CRs-Fixed: 2676919
Currently there is no ini to control the rrm support on
SAP.
Add a new ini to enable/disable rrm on SAP.
Change-Id: Idef8da807bc5f8e2b4a1d61997824006e78b0cf6
CRs-Fixed: 2658926
Currently, only broadcast disassociation is supported
and deauth is sent in a unicast manner.
With peer delete all support, HDD sends a single call
to PE for broadcast deauth request. PE module sends a
single broadcast deauth frame and on TX completion,
calls vdev_mgr_peer_delete_all_send. This issues the
new WMI_VDEV_DELETE_ALL_PEER_CMDID to FW to cleanup
peers entries corresponding to VDEV ID and also flush
TIDS internally.
On receiving the peer delete all response, target_if
cleans object manager entries and datapath cleans up.
But PEER unmap is done iterating through all peer entries
individually. After this a single eSAP_STA_DISASSOC_EVENT
is received in HDD signalling the completion of broadcast
deauth procedure.
Change-Id: I928461606154380eef21a02cc7306921ceb9e16e
CRs-Fixed: 2585005
Add INI - gActionOUIReconnAssocTimeout to configure driver
to do:
1. Driver will not send deauth to the AP after association timeout.
2. Reconnect to same BSS again if the last association failure
is association response timeout.
Default="00E04C 00 01"
The change fixes IOT issue with certain AP which doesn't
response first association request frame sometime. But the AP
would response second association request.
Change-Id: I9f7b8d14aaaaa97f08856c8b62e49b145db3ac91
CRs-Fixed: 2653877
Control path use the data path variables to detect PN replay
and also modify the same.
Thus move the PN replay detect logic in objmgr peer in control path.
Change-Id: I8d1cd4b86eac3f6a7343c4616e398579bc4932ae
CRs-Fixed: 2658077
Currently the driver fails the ACS process
if no channel is found suitable for SAP by
ACS and thus hotspot cannot be enabled.
Fix is to force SAP to come up on some
default channel, this behaviour would
be controlled via an ini to that customers
can choose whether to opt for this behaviour
or not.
Change-Id: I8a63cf0c5d42802e33f4ad67a33d148a4da54d2a
CRs-Fixed: 2658297
Currently the driver allows roaming to the BSSID
which it is already connected, which can lead to
many unexpected behaviour, for eg. if the SAP
to which the DUT is connected turns off, then the
DUT would try to roam to other BSSID of the same
SSID, and in case the SAP turns on back in time,
then the DUT would re-associate to the same BSSID.
Now if the subnet may change, and since the DHCP
does not happen again in roaming, it would then
lead to NUD failure.
Fix is to introduce an ini to allow/disallow
roaming to the same BSSID.
Change-Id: Ibd04fcd7384c0987db5bb6dae1a26ee077456290
CRs-Fixed: 2634860
Remove max_tx_power from wlan_mlme_power struct
and ini_tx_power from lim_max_tx_pwr_attr struct
and all their instances.
Change-Id: I982a15b71b64d368b623128e04f09a8f3bf4f5ec
CRs-Fixed: 2645922
Introduce an INI "ap_tx_pwr_scoring" to indicate firmware about ap tx
power weightage so that firmware can use ap tx power weightage to
calculate candidate AP's score.
Change-Id: I8831c571162f044f4ae204ef0edfc59942f36837
CRs-Fixed: 2647115
Add pointer str1 NULL check before use in mlme_acs_parse_weight_list()
in case user side has wrong configuration.
Change-Id: I7a1552e417a7571d138a2c1c526aa2f9d0015529
CRs-Fixed: 2642567
Currently QDF_MAX_NUM_CHAN/POLICY_MGR_MAX_CHANNEL_LIST aren't aligned with
NUM_CHANNELS, these unalignment may cause some potential OOB access.
So replace QDF_MAX_NUM_CHAN/POLICY_MGR_MAX_CHANNEL_LIST with NUM_CHANNELS
to keep unified.
Change-Id: Ib6c81a3979f2fd29ba1ec678f018a6704b599385
CRs-Fixed: 2644066
Add host driver support for MCS 12/13, a Q-Q PHY feature.
The following changes are being introduced as a part of this
- Advertisement of the MCS 12/13 using the QCN IE
- Interaction between the Host and the FW regarding the target and
peer capabilities for the new features introduced.
- The new data structures and variables to populate and use the feature
capability
- Routines to add and parse the IE.
Change-Id: I2b91a271d30b1230ef7bb14ee08d0b9da2706db4
CRs-Fixed: 2610277
Use INI "sta_disable_roam" to disable roaming on STA interface if
connection on other interfaces ex. p2p, ndp comes up. Each bit of
the INI "sta_disable_roam" represents an interface.
ex. LFR3_STA_ROAM_DISABLE_BY_P2P BIT(0)
LFR3_STA_ROAM_DISABLE_BY_NAN BIT(1)
As INI "sta_disable_roam" is generic for all the interfaces, cleanup
for INI "p2p_disable_roam" done.
Change-Id: Icd05a97c640ca07978d9960a33de036ed6fe38df
CRs-Fixed: 2637555
Presently vdev delete is sent to firmware 1st and the object manager
vdev delete is deleted after all the references are released.
With this change the vdev delete is sent to firmware when all the
references are released and the vdev delete is sent to firmware via
the object manager vdev delete notification.
Change-Id: I67bea0d2b2a0d2d9eb4602e5d0b8bbdcafdd4d26
CRs-Fixed: 2618278
Add ini support for DFS Channel Ageout Time, the time upto which
DFS channel information such as beacon found is remembered.
This ini is used to set the ageout timer value from host to FW.
If not set, FW will disable ageout time.
This value is sent as a WMI_PDEV_PARAM_SET_DFS_CHAN_AGEOUT_TIME
as part of WMI_PDEV_SET_PARAM_CMDID.
Change-Id: I99553fa87a4025f03c52b4b387a414ba06c2c457
CRs-Fixed: 2625996
Introduce ini for roaming_triggers to enable/disable specific
roaming triggers. This will be the master ini to control roaming
triggers. If this ini is set to zero, roaming will not be enabled
on the sta interface unless its enabled via vendor command.
A new roaming trigger - Sta kickout roaming is introduced in
firmware, include this bit support also in the ini.
The value of this ini will be sent over the wmi command
WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID during RSO start.
Reset this value to 0 during RSO stop if RSO stop is due to
disconnect or roam synch failure.
Change-Id: I02f207cdde9d8fb68cd91fab07572baa9e7ac50d
CRs-Fixed: 2631712
