Currently use of comamnd QCA_NL80211_VENDOR_SUBCMD_OEM_DATA
is to pass data blobs from Application to FW but there is
no mechanism to send the data blobs from FW to Application.
To meet the above requirement update the usage of existing
OEM DATA command to use it as a vendor event as well to
send data blob from host to Application.
Change-Id: I8df98f850f4dd56f55dba43c5364a52c425ba9ed
CRs-Fixed: 2573468
After every roam happens or when neighbor report is sent by the
firmware, it sends the WMI_ROAM_STATS_EVENTID to host.
Add support to handle WMI_ROAM_STATS_EVENTID event from target
after every roam.
Change-Id: I4474135ac64ebfb17109d503fbd1c3d637457a73
CRs-Fixed: 2576258
To enhance visibility of 6GHz AP, 6G only AP shall send
Fils Discovery frame periodically in one beacon interval.
Change-Id: I51487380fca10418d2260dc2612e2adcf6cbb93b
CRs-Fixed: 2562434
Add new stats_id WMI_REQUEST_MIB_STATS &
WMI_REQUEST_MIB_EXTD_STATS in WMI_REQUEST_STATS_CMDID
to retrieve MIB statistics from fw.
Change-Id: I17bccc2673d1a2ce035db04d8426bab49db80790
CRs-Fixed: 2548165
Currently the driver doesnot support the sending and receiving of the
ani level from the firmware.
Add WMI and driver framework support to fetch the ani level.
Change-Id: Ib8271a2b7f62bafb22429113fbfb405cc81379ed
CRs-Fixed: 2554677
This print is a debug measure that addresses an issue where the
HE MCS NSS Map is set to an invalid value. Although rate checks
exist already which take corrective action, this proactive print
adds information useful for addressing corner cases should
they appear.
CRs-Fixed: 2554277
Change-Id: I8e770639472409d96654dc8652ea8c9d210c4965
Add WMI changes for the API he_muedca_mode
to swicth between manual, host and FW dynamic
muedca param selection.
Change-Id: If43b5da483fe082294bda33f8951187ebc7ea3c7
CRs-Fixed: 2554378
Set WMI_PEER_INTER_BSS_PEER peer flag in the fixed param in
WMI_PEER_ASSOC to differentiate between inter-bss and intra-bss peer.
Change-Id: Ic3f54646bfcf988ce53c3d581bacea65070a5036
1) Add Spectral scan mode and agile center frequency in WMI
commands to indicate the current mode.
2) Obtain the Agile Spectral capability from the chain mask table.
CRs-Fixed: 2455967
Change-Id: I88ba6fc1ecf9b530a6b516d0c1e4ce88702c6d1f
Currently the FW expects the flag of
scan chan cmd to be set if the max BW
is filled for all the channels, which
is not set by driver.
Fix is to set the flag's 2 bit to allow
FW to use the max chanel BW.
Change-Id: Id3ce009fbd3c846713d456436c70b44a44428577
CRs-Fixed: 2550434
Add API to know whether 6ghz is supported. Also add API to know
whether an operating class is 6ghz operating class.
Change-Id: I75747502c0033e31d119e58a2254b220646bba10
CRs-Fixed: 2556998
1) Remove the definition of plm_ch_list from
struct plm_req_params and add plm_ch_freq_list
into the same struct given frequencies will be
used directly before passing WMI command to
firmware.
2) Remove redundant channel frequency list from the
following API functions' parameters:
send_plm_start_cmd
wmi_unified_plm_start_cmd
send_plm_start_cmd_tlv
Change-Id: I982412076b422356037d9bbfa2077affd1056189
CRs-Fixed: 2560085
target_if F/W event handler is moved from wma to cmn part per
MCL/WIN converge requirement, clean up legacy call back.
Change-Id: Ifacc6bb46e6bde1a73d9953e3403551dd2e92939
CRs-Fixed: 2555080
Add WMI scheduler thread context execution framework
to process firmware events in the common project.
Change-Id: If56a4767ee9428d2f93d54ccbf5a8bb17e89e0f4
CRs-Fixed: 2554727
Add a qdf counter to know number of qmi stats requests. Reset the
counter when WoW is exited.
Change-Id: Ie0c51fbd6eb2e7530dba01912443e7fc85726e52
CRs-Fixed: 2539999
Due to channel number ambiguity with introduction of 6Ghz support
policy manager APIs are updated to use frequency values instead
of channel number. Update set pcl WMI handling to adapt for frequency
usage.
Change-Id: I69bac781036ed9faee8842190d9bf19abca3ec61
CRs-fixed: 2540002
Add support to scan for the 6GHz band capabilities
IE and parse the IE. Added peer assoc param for updating
the minimum data rate advertised by the peer in 6GHz
Opration information.
Change-Id: Iebb4379d321832f3ed2bcd3174a54843fa2d497c
If more than MAX_NUM_CHAN_PER_WMI_CMD are present, wmi buffer size can
exceed the maximum allocated buffer size. So iterate over the channel
list, and send multiple messages till channel list is empty. Also check
if 6 ghz channel is a PSC channel and mark channel flag accordingly.
Change-Id: I977a2d220c750cec1f261377b3838360bd8c0df3
CRs-Fixed: 2522763
TLV and non-TLV definitions of vdev mgr ops are in component_dev,
they are carved out to a separate file in cmn_dev/wmi for adapting
target_if/vdev mgr component, they are made part of same file
which conflicts tlv design. Create separate file for tlv ops
to definitions and enable respective pointers.
Change-Id: I1e67c7c59adee61b4eb46acb8f51a7a6c385f056
CRs-Fixed: 2517009
Add support for WMI over QMI to reduce power consumption for
periodic stats report.
Change-Id: Ic57b2bd18be803c97ffeea2e0073751d31e02202
CRs-fixed: 2521835
vendor_roam_score_algorithm is added in order to
enable/disable roam score algorithm.
With this roam score Algorithm, AP score will be calculated
based on below equation:
AP Score = (RSSIfactor * rssiweight(0.65)) +
(CUfactor *cuweight(0.35))
Add vendor_roam_score_algorithm inside scoring_param
and inside function send_roam_scan_offload_ap_profile_cmd_tlv
populate score_param->vendor_roam_score_algorithm_id
from ap profile.
Change-Id: I21bb788d96a34c3bf237f0d304e51a7f4664d2ee
CRs-Fixed: 2517492
Enable DISA WMI commands for FIPS CCM test
by moving DISA WMI code to unified tlv files.
Change-Id: I90e82fef0e7e365faa6e15d555bf4d431214e14a
CRs-Fixed: 2516897
Currently the host gets service_ready_event and service_ready_ext_event
during the init sequence as a part of handshake with firmware. As the
size of the service_ready_ext_event exceeds on adding further
parameters, new event is created.
Add support for WMI_SERVICE_READY_EXT2_EVENT to be processed after
WMI_SERVICE_READY_EXT_EVENT based on the service bit
WMI_SERVICE_EXT2_MSG.
Also add support to extract the reg db/bdf version information that
comes inside the ext2 event.
Change-Id: If0b57af362e7eb653f9189b912ec1dd3efb0f731
CRs-Fixed: 2501132
Configuration for Issue:-
DUT configuration:-
1. Configure DUT's country as US where channel 165 does
not support channel bandwidth of 40 mhz.
AP Configuration:-
1 Configure the AP in a country where channel 165
supports channel bandwidth 40MHZ.
Scenario of the issue:-
1.Connect to a diff AP on some channel x with same SSID,
and then roam to this AP.
Observation:-
The DUT would connect in 40 mhz to this AP instead of 20Mhz,
which violates the DUT's country reg rules.
Expectation:-
The DUT should re-connect only in 20Mhz on channel 165, or
only in max BW supported by reg in that country.
Issue:-
The DUT does not consider the max bandwidth allowed for the channel
in the country configured, and allow the re-association only
in the respective bandwidth.
Fix:-
Send the max BW supported by the channels in the current
reg domain to the FW so that it considers the max BW of the
channel and AP capability and then roam in the respective BW
only.
Change-Id: I977090c58e378e83cb5a3ee84a72afd018e8c428
CRs-Fixed: 2508187
If the FW sends a pktlog checksum in the FW ready event, store that in
pl_dev and use it as buf_hdr.version in the pktlog buffer header.
Also, use a new magic value to identify the checksum in the
buf_hdr.version field.
If the FW does not send the checksum, then the existing magic number
and standard version number would be maintained.
Change-Id: Ib08c093a9b54495a2c5b7e0e163207f2b1eb4ce2
CRs-Fixed: 2508828
Userspace may configure the roam trigger bitmap to WLAN host
driver to enable particular roam trigger reasons. Convert the
bitmap to the format of firmware trigger reason bitmap and send
to firmware.
Change-Id: I9fc78c180bd25c995dfd380f80e52e3eb302fce3
CRs-Fixed: 2507611
The supplicant sends del_pmksa command to delete the pmk,pmkid
for a particular bssid. In this command pmk_len will be 0.
In send_set_del_pmkid_cache_cmd_tlv() the host driver currently
checks the pmk_len to set WMI_PMK_CACHE_OP_FLAG_FLUSH_ALL.
If pmk_len is 0 WMI_PMK_CACHE_OP_FLAG_FLUSH_ALL is set, which
is not correct. pmk_len will be zero in both the flush and delete
cases.
So add a new flag is_flush_all which will be set to true when the
supplicant sends pmksa flush command.
At WMI based on this flag set the flush flag to the wmi cmd.
Change-Id: I7626c500721a4b8cccbb21a08d4235c041456d1b
CRs-Fixed: 2502478
Full scan period is the idle period in seconds between two
successive full channel roam scans. Configure this to firmware
along with scan period as part of roam_scan_offload request
Change-Id: I3d629f0735b50a5b8116b422779ae423c15cae1d
CRs-Fixed: 2507604
Add cfr_enable flag in Probe response, so that FW can start CFR
capture for particular client.
Change-Id: Id38b61317384a069308de4931463f1aef4f65f38
CRs-Fixed: 2502030
