Refactor the below two ini items to new converged cfg/ini
infrastructure:
"gEnableChangeChannelBandWidth"
"extscan_adaptive_dwell_mode"
"extscan_adaptive_dwell_mode" - move this to scm module
"gEnableChangeChannelBandWidth" - move this to mlme
Change-Id: I1ca6657a95c2cd47057f11ccf23c47347f3fc33b
CRs-Fixed: 2394240
Add the WMM config ini config
CFG_TL_DELAYED_TRGR_FRM_INT_NAME to MLME cfg.
Introduce the basic infra APIs related to these configs
from mlme.
Change-Id: Ifaf8072a78f21760e00973e625d7c8e41d8b51a6
CRs-Fixed: 2361533
Remove the following scan and ap protection related ini items:
CFG_AP_ENABLE_PROTECTION_MODE_NAME
CFG_ENABLE_MAC_ADDR_SPOOFING
CFG_SCAN_AGING_PARAM_NAME
Replace the corresponding hdd_config variables and replace
these variable callers with ucfg api from corresponding module.
Change-Id: I99a2659e2151ad285e9451b9e9cc036a199581a3
CRs-Fixed: 2378991
Only when F/W indicates 2g vht20 supported and ini config
gEnableVhtFor24GHzBand=1, 2g vht20 can be enabled.
Steps:
For chips wmi_service_ext_msg supported:
1. hdd_component_psoc_open->mlme_cfg_on_psoc_enable->
mlme_init_vht_cap_cfg, read and save ini cfg:
gEnableVhtFor24GHzBand.
2. WMI_SERVICE_READY_EXT_EVENT indicates 2g vht20 capability by
mac_phy_caps->vht_cap_info_2G.
3. init_deinit_populate_mac_phy_capability calls
extract_mac_phy_cap_service_ready_ext_tlv
to extract vht_cap_info_2G, and set to
psoc->tgt_if_handle->info.mac_phy_cap.
4. hdd_update_tgt_cfg->hdd_update_vhtcap_2g->
wma_get_caps_for_phyidx_hwmode, get target capability,
and combine ini cfg, update 2g vht20 cfg in mlme.
For chips wmi_service_ext_msg unsupported:
1. hdd_component_psoc_open->mlme_cfg_on_psoc_enable->
mlme_init_vht_cap_cfg, read and save ini cfg:
gEnableVhtFor24GHzBand.
2. WMI_SERVICE_READY_EVENT indicates 2g vht20 capability by
hal_reg_capabilities-> wireless_modes
REGDMN_MODE_11AC_VHT20_2G bit.
3. init_deinit_populate_phy_reg_cap calls wmi_extract_hal_reg_cap
to extract hal_reg_capabilities, and set to
regulatory component by ucfg_reg_set_hal_reg_cap, saved
in wlan_regulatory_psoc_priv_obj->reg_cap.
4. hdd_update_tgt_cfg->hdd_update_vhtcap_2g, get and target
capability and combine ini cfg, update 2g vht20 cfg in
mlme.
Change-Id: Id4f2edd129bb1eefec3e39b4246c5f52b2b4124a
CRs-Fixed: 2384842
2g vht20 config should be decided by both capability indicated
by target and ini config. Only when F/W indicates 2g vht20
supported and ini config gEnableVhtFor24GHzBand=1, 2g vht20 is
enabled.
Change-Id: I5b7ad8f82b6000096327c501dc84ad05480ef0fd
CRs-Fixed: 2381514
Struct mlme_ht_info_field_2 has two different layouts depending upon
endinaness, but for one of the fields the naming does not match.
Rename the nonGFDevicesPresent field to be consistent with its
counterpart non_gf_devices_present.
Change-Id: Iafec9976d5f890ae6555af35c40186afacb5c325
CRs-Fixed: 2379073
Based on new cfg framework, defines below five WNI cfg items and one
INI cfg:
- WNI_CFG_APSD_ENABLED
- WNI_CFG_OBSS_DETECTION_OFFLOAD
- WNI_CFG_OBSS_COLOR_COLLISION_OFFLOAD
- WNI_CFG_CURRENT_TX_POWER_LEVEL
- WNI_CFG_LOCAL_POWER_CONSTRAINT
- gTxPowerCap
Change-Id: I5546ea7a4efd142b546ad10a40712d40d2d3ea0d
CRs-Fixed: 2375857
All WNI configurations will be cleanup based on new cfg framework, so
change Change WNI_VALID_CHANNEL_LIST_LEN to VALID_CHANNEL_LIST_LEN.
Change-Id: I805be88ecdcca90cf3a19d1784bf8f8c261b6ca4
CRs-Fixed: 2379748
Make changes to the legacy code to support the
new SET KEY converged infrastructure.
Change-Id: Ic5359e3a9035ac5f2a937a9a1013fa92764cda9d
CRs-Fixed: 2358795
Add dot11mode related cfg items in mlme cfg, and replace
old WNI dot11 modes with new MLME DOT11 mode enums
Change-Id: I6e866959f440ae781432c8aaa724b229c0874856
CRs-Fixed: 2362540
Update qcacld driver to move IBSS INI params to converged CFG
component and cleanup HDD ini entriesi
Change-Id: Id8e4c0505113e556a8d64915a648f17fc5c0daf5
CRs-fixed: 2358493
Add two new WCNSS_qcom.ini values:
"roam_score_delta" - Factor by which the new roaming candidate
ap score should be greater than the score of the current
connected AP.
"roam_score_deltabitmap" - Roam triggers for which
roam_score_delta needs to be applied on the roam score of the
candidate AP.
Populate these two values to wlan_mlme_scoring_cfg from cfg
component in mlme_init_scoring_cfg. The values are sent to
firmware over the WMI TLV WMI_ROAM_AP_PROFILE in the below code
flow:
csr_update_score_params()->__lim_process_roam_scan_offload_req()
->wma_process_roaming_config()->wma_roam_scan_offload_ap_profile
Change-Id: I64f2a2328e485418547dae937c657f85225f1457
CRs-Fixed: 2367910
Add the following new WCNSS_qcom.ini value:
"prefer_roam_score_for_candidate_selection" - choose to sort the
candidates on roam score or preferred AP list send in the BTM
request frame by AP.
When this ini is set, host driver will
modify btm_offload_config bit 7 which will be read by firmware
to get this ini value.
“roam_candidate_validity_timer” - roam cache entries validity
timer. The candidates in the roam cache are valid only for this
time value. This value is sent to firmware over the wmi command
on the structure wmi_roam_offload_tlv_param
"btm_disassoc_timer_threshold" - Disassociation timer threshold
to wait after which the full scan for roaming can be started
after the AP has sent the disassoc imminent
Change-Id: I3ba5ba2182b1b6d722d9c315757332a1b3e62521
CRs-Fixed: 2369018
Add new WCNSS_qcom.ini value:
"prefer_btm_query" - Set this flag to enable the firmware to
send btm query for neighbor list. If this flag is not set,
the firmware will fallback to current mechanism of sending
11k neighbor report request instead of btm query.
When this prefer_btm_query is set, host driver will modify
btm_offload_config bit 8 which will be read by firmware to
get this ini value.
Change-Id: Id424c0da7207b0185cee67172782ef5c1d9fd131
CRs-Fixed: 2369000
Add new ini item "bss_load_sample_time" to send the monitor
time window for which the beacons are to be sampled to collect
the bss load information.
Also add changes to send bss load trigger parameters only during
RSO start during initial connection
Change-Id: I61d1f3745b56199838fc886f1ed3a05786653501
CRs-Fixed: 2372147
Introduce the following new WCNSS_qcom.ini values:
"enable_bss_load_roam_trigger"
"bss_load_threshold"
Send these values over the new wmi command,
WMI_ROAM_BSS_LOAD_CONFIG_CMDID if "enable_bss_load_roam_trigger"
is set to true.
This wmi command will be sent to firmware as part of the RSO
start or update config.
Change-Id: Ib2e21904bc7b8d87e5f51824d2694b90a3ac53f2
CRs-Fixed: 2367770
Currently, the support for beacon reception stats is only dependent on
the FW.
Add an ini so that the user can also have a control over the stats
Change-Id: I4a1e654b9d1598836378def494b37a997904d77a
CRs-Fixed: 2366473
WNI_CFG_WPS_UUID should be refactored and adopted by the mlme
component.
Move the cfg item to cfg_mlme_wps_params.h
Change-Id: I79db155ad16998e9d7a7e20c01efbcba1681d61e
CRs-Fixed: 2366599
Add the functionality changes to replace the legacy powersave
parameters corresponding to the ini values that were converged.
Remove the legacy powersave ini items.
Change-Id: I1da9af9aac4a02a16dc22a43f7f9d526e196d599
CRs-Fixed: 2364964
Add basic infra to move the following Powersave related
ini to MLME component:
CFG_ENABLE_IMPS CFG_ENABLE_PS
CFG_AUTO_PS_ENABLE_TIMER CFG_ICMP_DISABLE_PS
CFG_BMPS_MINIMUM_LI CFG_BMPS_MAXIMUM_LI
CFG_DTIM_SELECTION_DIVERSITY
This change brings in mlme_init changes, mlme_public_struct.h changes
and cfg_mlme file changes for power save parameters.
Also remove the ini CFG_ICMP_DISABLE_PS_NAME as it is not used.
Change-Id: Ifd74d276b12acc8cd9740c25ee3ca261ed7d0143
CRs-Fixed: 2356897
WLAN Latency Manager support is one of the capabilities that is sent
along with the service bits by firmware. Currently, driver is not
exposing this feature to the user space.
Create and add support for a feature flag to expose this feature to the
userspace.
Change-Id: Ica8213bdaeb32c7be01b6a71a7d8b7a32dc8611b
CRs-Fixed: 2363704
The function mlme_get_psoc_obj() is used to get the mlme_obj and
error handling is taken care inside the function if mlme_obj is
null.
Remove the error message in callers of mlme_get_psoc_obj.
Change-Id: Ie7cda790758ad21b1a0275d313a97f322a2f6fd7
CRs-Fixed: 2365042
Add the following WLM and RRM ini configs to MLME
cfg:
CFG_LATENCY_ENABLE
CFG_LATENCY_LEVEL
CFG_LATENCY_FLAGS_NORMAL
CFG_LATENCY_FLAGS_MOD
CFG_LATENCY_FLAGS_LOW
CFG_LATENCY_FLAGS_ULTLOW
CFG_RRM_ENABLE
CFG_RRM_MEAS_RAND_INTVL
CFG_RM_CAPABILITY
Change-Id: I714aca1e9bc6d3c330934753364d7f58d93a28d7
CRs-Fixed: 2353103
Add the following WLAN_REG ini configs and FE_BEAMFORM
cfg items to MLME cfg:
1. WNI_CFG_11D_ENABLED
2. WNI_CFG_11H_ENABLED
3. WNI_CFG_TX_BF_CAP
4. WNI_CFG_AS_CAP
5. WNI_CFG_DISABLE_LDPC_WITH_TXBF_AP
Introduce the basic infra APIs related to these configs
from mlme.
In csr_roam_open_session, lim_populate_vht_mcs_set,
lim_sta_send_add_bss, populate_dot11f_tdls_ht_vht_cap,
populate_dot11f_vht_caps and sme_update_nss, local structure
is updated instead of mlme global structure for vht caps and
thus the mlme vht caps contains only the default values.
Fix this by updating mlme vht caps in mlme_update_vht_cap.
Change-Id: I1a948d7a44ad2bcc7f711c46b278971d7e4026e7
CRs-Fixed: 2354562
Add power items related CFG items in new file,
and store the respective inis in MLME component
Change-Id: Iac183da52495aca07c6270edeb9f383ab49c1ff5
CRs-Fixed: 2341900
The second part of LFR INIs are defined dynamically in legacy codes.
Refines these INIs and APIs based on new cfg component.
Change-Id: I89869c50952bf2fe403079299b3902fc53c11d61
CRs-Fixed: 2346784
Based on new cfg component, refactor CFG_TX_POWER_CTRL_NAME and clean
up related legacy codes.
Change-Id: I6dd317d5065c4111b71a9fe94d9b9af1f7d3d664
CRs-Fixed: 2355918
Based on new cfg component, refactor INI CFG_OVERRIDE_HT40_20_24GHZ_NAME
and remove legacy codes.
Change-Id: I5b4ed96a4930a9358bd93ee809bf5cddb2787fb4
CRs-Fixed: 2354476
Cleanup multiple HT related CFG/INI Items which are already moved to the
MLME component.
Also move gShortSlotTimeEnabled INI from HDD to MLME component
Change-Id: Ie8c19f508401d4d72990f35ea5dcc18d45f0f16b
CRs-Fixed: 2354687
Refactor ini items gSapForce11NFor11AC and gGoForce11NFor11AC
into new mlme component.
Change-Id: I85e2f7f9ae14a23c322572290b095aae0f29b0ec
CRs-Fixed: 2354940
