Some targets have a single synthesizer and it allows
a single Spectral detector to scan in 160 MHz /165 MHz.
Enable Agile Spectral scanning in 160 MHz / 165 MHz for
such targets. Agile creq2 will be populated in the WMI
command after WMI interface changes are merged.
CRs-Fixed: 2648480
Change-Id: I8522cbeeab29ac41479e3041eea376b081c0758a
WMI commands for DBR and CFR are based on pdev id, so need to convert
host pdev id and target pdev id when tx wmi commands or rx wmi events.
Change-Id: I54bf4a28a285e5b4dfdd125aeaabb9968a6d052a
CRs-Fixed: 2634729
In direct buffer rx component, it required to pdev id and mod id match
at same time, so use new pdev id conversion backup and convert pdev id
actually.
Change-Id: If53bde84564becd91f2dd0e20b002da2961dccd2
CRs-Fixed: 2528401
Extended service ready event has a tlv
containing the spectral bin scaling parameters.
Populate the spectral capabilities using this info.
CRs-Fixed: 2379652
Change-Id: I0b4648302e7170b5965cf1aec68638e70cd36e73
Spectral HW time stamp gets reset when a reset happens in
within target. This can potentially result in unpredictable
behaviour during classification. To mitigate this calculated
offset is added to the time stamp value in the FFT report.
HT = Spectral HW timer
AT = Actual time stamp in spectral report
CF = Time stamp correction factor
CT = Corrected time stamp
L = Time stamp in the last FFT report before reset
F = Time stamp in the first FFT report after reset
D = Time gap between the last spectral report before reset
and the end of reset(This is provided by FW via direct
DMA framework)
***Target Reset***
^
|
|<---D---->| time line--->
_______________________________________________________
^ ^ ^ ^
| | | |
HT --> 0 L 0 F
AT --> 0 L F
CF --> 0 0 (L+D)
CT --> 0 L (F+L+D)
Spectral driver corrects the time stamp received from target
using the following formula and sends upwards.
CT(Corrected time stamp) = AT(Actual time stamp) +
CF(Correction Factor)
Calculation of Correction factor (CF):-
---------------------------------------
Initialization : CF = 0
CF += (L + D) (Done only for the first spectral report after reset)
This scheme takes care of the wrap around in the 32 bit time stamp
which would have occurred if the timer was not restarted due to
target reset.
CRs-Fixed: 2356382 2355486
Change-Id: I17b55d39eb91eb03b867bcfddaf3eb03d1fc5d1b
In the existing converged component, WMI TLV APIs are implemented in
a generic manner without proper featurization. All the APIs exposed
outside of WMI are implemented in wmi_unified_api.c and all the APIs
forming the CMD or extracting the EVT is implemented in wmi_unified_tlv.c.
Since WIN and MCL have a unified WMI layer in the converged component and
there are features within WIN and MCL that are not common, there exists a
good number of WMI APIs which are specific to WIN but compiled by MCL and
vice-versa. Due to this inadvertent problem, there is a chunk of code and
memory used up by WIN and MCL for features that are not used in their
products.
Featurize WMI APIs and TLVs that are specific to WIN
- Air Time Fareness (ATF)
- Direct Buffer Rx (DBR)
- Smart Antenna (SMART_ANT)
- Generic WIN specific WMI (AP)
Change-Id: I7b27c8993da04c9e9651a9682de370daaa40d187
CRs-Fixed: 2320273
