802.11BE D1.0 9.4.2.295c.4 Supported EHT-MCS And NSS Set
field specifies maximum 4 optional EHT MCS map, which are
20 MHz-Only STA, BW <= 80 MHz except 20 MHz-Only STA,
BW = 160MHz and BW = 320 MHz.
Therefore set WMI_HOST_MAX_EHT_RATE_SET to 4.
Also add a debug message to log peer_flags_ext.
Change-Id: I3d56998bf0de381ef147d6c0551dcdb7fd935f60
CRs-Fixed: 2963536
Set the SAE EAPOL offload support in resource config based on
WMI_SERVICE_SAE_EAPOL_OFFLOAD_SUPPORT bit received in service
bitmap from Firmware.
Change-Id: I878736105c070df514dfe8d989541227b3baad11
CRs-Fixed: 2957082
Firmware generates wmi Rx diag events every few milliseconds,
and processing the same in system shared work queue may lead to
work queue lock-up detection. Hence, move Rx diag event processing
to dedicated work queue.
Change-Id: I10cdde317794e35bc6d10677ab76ea24a66e1880
CRs-Fixed: 2941409
When obss scan is enabled, FW will trigger scan periodically by
a timer. If a scan was triggered, FW need to access host memory
for data transfer. Occasionally, suspend may happen during one
scan, then FW is unable to access host memory and fw will crash.
So disable the obss scan before suspend.
Change-Id: Ie507da929a3701473cb57888e96e702e34d4c95a
CRs-Fixed: 2927239
Fill peer assoc mlo params in peer assoc request command.
Also add definitions to the WMI_SERVICE_11BE.
Change-Id: Ied7959e022ee27f3bd698b84dc801491175f85b3
CRs-Fixed: 2934417
In WMI_HOST_TP_SCALE, add an option to support 6% transmit power scale
configuration.
Change-Id: I11a67f0efd13ba2c7f2d8d546643a1af37f33613
CRs-Fixed: 2936987
Add new reason code WMI_HOST_ADD_TWT_STATUS_SCAN_IN_PROGRESS
to handle add dialog rejection due to scan is in progress
at firmware.
Change-Id: I30c3d1096690bd0cb7a669206f087e006c23ea44
CRs-Fixed: 2923289
Extract the 11BE flags advertised by FW in WMI_SERVICE_READY_EXT2_EVENTID
and update the regulatory pdev wireless modes. The wireless mode is
currently represented as 'uint32_t' and all the 32 bits are exhausted.
To accommodate the new 11BE flags, change the data type of wireless_modes
from 'uint32_t' to 'uint64_t'.
Add a regulatory phymode 'REG_PHYMODE_11BE' in enum reg_phymode.
If the chip does not support 11BE phymode, FW advertises it via
WMI_REGULATORY_PHYBITMAP enum with a value of REGULATORY_PHYMODE_NO11BE.
Extract the phybitmap and store it in the regualtory
as 'REGULATORY_PHYMODE_NO11BE' bitmap.
CRs-Fixed: 2901260
Change-Id: I4ed3fc7c907b1f76e59efb347c747acea2a163b0
The firmware sends new reason codes due to roaming in
progress and channel switch. Add new reason code for
TWT session.
Change-Id: I3820ac74910e382f5a029de85f8e0915220bb996
CRs-Fixed: 2908384
Updated the EHT related variables as per latest fw cmn headers.
Address review comments from previous EHT gerrits.
Change-Id: I67cd58a4efcf3e06d2ca3b5570432593b1d80825
CRs-Fixed: 2902607
Add 320Mhz band width support and EHT capabilities information in
WMI peer assoc command.
Change-Id: Ie4ee95fb1790c828275e90b384b2bdc04efb3f29
CRs-Fixed: 2882054
EHT capapilities will be received as part of ext2 service ready message.
Update the structure as per firmware common header file and extract the
EHT capabilities field.
Change-Id: Id2dd170db4de588008742f95493d4d06a6431f1c
CRs-Fixed: 2857802
Add support to read the WMI service bit describing support
for the DCS AWGN interference detection mechanism.
CRs-Fixed: 2906768
Change-Id: Id062b9d63a09f522ac1efdbaf6731665fa438630
Add support for storing AWGN interference information for
dynamic channel selection
CRs-Fixed: 2903860
Change-Id: I5d0b6cc0a55303cfb27a02b99aba066557ad9c7d
Add new TWT teardown status code to indicate firmware teared
down the TWT session due to concurrent connection established.
Change-Id: I9b0fb5c5179355f34bd07e91a996da3ade1c9ce8
CRs-Fixed: 2899575
Enable lower 6G edge channel ch2 (5935MHz) for APL2 6G regdmn
using a service bit WMI_SERVICE_ENABLE_LOWER_6G_EDGE_CH_SUPP,
which is not enabled by default.
Also, disable upper 6G edge channel (7115MHz) using another
service bit WMI_SERVICE_DISABLE_UPPER_6G_EDGE_CH_SUPP, that
is enabled by default.
Change-Id: Ia7cb7f7d3165375178adbe70adb19b8671496b6d
CRs-Fixed: 2885623
In order to support different power levels of 6G AP and client,
the channel list event from FW namely "REG_CHAN_LIST_CC_EVENTID"
is modified to add few parameters specific to 6GHZ devices.
Hence the existing event is replaced by REG_CHAN_LIST_CC_EVENT_EXT for
all 2G/5G/6G pdevs in FW. Therefore, after the service ready event, FW
sends the channel list for the configured country/regdomain via
REG_CHAN_LIST_CC_EVENT_EXT. This mandates that all host software need
to have the processing capability of REG_CHAN_LIST_CC_EVENT_EXT to bring
up the AP.
As there can be host software which has not yet implemented the
version of "REG_CHAN_LIST_CC_EVENT_EXT", backward compatibility is lost
if "ONLY REG_CHAN_LIST_CC_EVENT_EXT" is sent by FW.
Hence a 3 way handshake between host and FW is established.
1. FW advertises its capability of processing REG_CHAN_LIST_CC_EVENT_EXT
id via wmi service bit 'wmi_service_reg_cc_ext_event_support'.
2. If the host is capable of processing the "REG_CHAN_LIST_CC_EVENT_EXT"
event id (which is done based on registration of this event), host
sends the capability in WMI_INIT_CMDID setting a bit in host_service_flags.
3. Based on host capability advertised in WMI_INIT_CMDID, FW decides to
send the old event ("REG_CHAN_LIST_CC_EVENTID") or the new event
("REG_CHAN_LIST_CC_EVENT_EXT").
4. If there is no flag indicated by host to FW in WMI_INIT_CMDID, FW
by default sends the old event ("REG_CHAN_LIST_CC_EVENTID").
CRs-Fixed: 2876360
Change-Id: Ibe95f414ad9fff0e5641bcc6e60450ef9afe245b
Add support for TWT AP params not in range and IE validation failed
status code.
Presence of num_additional_twt_params is enough to extract the additional
params sent by the firmware, there is no need for extra status check.
Change-Id: I9fa6afd22aa4de1b2a5b75fa98a00f89768dd8cf
CRs-Fixed: 2890682
For some targets, FW expects WMI_REQUEST_UNIFIED_LL_GET_STA command
always over QMI irrespective of WOW state. FW will crash if this request
is sent over WMI on those targets. Currently there is no direct way for
the host to identify this requirement by FW. So FW may crash when this
WMI_REQUEST_UNIFIED_LL_GET_STA stats request is sent over WMI.
To resolve this, add service bit support for LL_GET_STA request over QMI.
With this change the INI parameter send_ll_and_get_station_stats_over_qmi
becomes obsolete and corresponding code will be removed.
Change-Id: I43f2827a0b1cae6e75f1224f452f8277d53736b2
CRs-Fixed: 2847483
FW advertises WMI_SERVICE_OCV_SUPPORT bit in service ready event if
firmware supports Operating Channel Validation feature.
Change-Id: Ida1ee9874f9cd32a684ceee728e3323306137c64
CRs-Fixed: 2880794
The host will send TPC power to FW via the new WMI cmd
WMI_VDEV_SET_TPC_POWER_CMDID going forward instead of
WMI_VDEV_PARAM_TX_PWRLIMIT to accommodate 6GHz channels.
But, to support backward compatibility for New Host+old FW
the TPC power will be sent to FW via legacy WMI cmds
WMI_VDEV_SET_PARAM_CMDID (during initial connection) or
WMI_VDEV_PARAM_TX_PWRLIMIT (power value change during RRM
req/bcn processing from connected AP) with the help of a
service bit WMI_SERVICE_EXT_TPC_REG_SUPPORT.
Change-Id: Iea1ecb62841c539c13a804ae9c475831b2d4c89c
CRs-Fixed: 2874250
Fix issue on enabling packet log.
Fix issue on logging CBF pkt in AP/STA mode.
Fix issue on setting data length 4 bytes aligned in pktlog header
, htt stats indication message header and Rx management TLV header.
Add CBF support for pktlog WMI enable command for firmware to enable
CBF receive.
Change-Id: Ib0067f32d7414be96503c4c67846c1312a59586e
Move ctrl_path_twt_stats related functions to appropriate source
and header files.
CRs-Fixed: 2871393
Change-Id: I7043259c102e5aee6cbb13260ce2bb0c53c17853
Add SAP and P2P GO d3wow feature support config to send it down
to FW during WMI INIT such that FW is aware when SAP and GO with
client connected mode d3 wow feature is enabled.
Change-Id: I04b398f71727112ce5c536bbf2bfcfd4eefe2752
CRs-Fixed: 2866604
Add a pci gen switch flag in the wmi resource config to send
to FW in the init command.
Change-Id: If3a50d80103387a8f1f77ecb43a16c7b41ce5a11
CRs-Fixed: 2865866
Firmware advertises service capability WAPI_CONCURRENCY_SUPPORTED
if it supports other security modes when WAPI is active. Get the
same from service capabilities to decide whether to accept a
new concurrent connection or not.
Change-Id: I718503e52be2dda8ebd440f5a68b496d846b6ffc
CRs-Fixed: 2858770
Since in wmi_gpio_config_cmd_fixed_param, the input
0 mean output, and 1 mean input, which is different
from host side enum gpio_direction. So add this fix
to do the right conversion.
Change-Id: Id60a9327e853440fd58a45c7c839109cf1f22c22
CRs-Fixed: 2856833
Firmware has added support for control path stats
infrastructure. Add wmi support to prepare wmi tlv buffer
and send WMI_REQUEST_CTRL_PATH_STATS_CMDID. In the response
path, add support to handle WMI_CTRL_PATH_STATS_EVENTID and
extract the tlv.
Change-Id: I930a44187af29adfda8acd90d0e41cff5fc94603
CRs-Fixed: 2856370
Using this option the user pd assert and root pd assert can
be linked together or unlinked from each other.
By default, a user pd assert leads to root pd assert.
Unlinking the user pd assert from root pd assert helps in
handling the selective radio recovery seamlessly.
Change-Id: I734805b060bf1cb11a0dc325bae5dbf6ed7db83f
Initially, Host updates the AKM only after the EAPOL
handshake. Due to this, Enterprise auth is not detected
for initial connection.
Add AKM in peer assoc command(WMI_PEER_ASSOC_COMMAND)
to the firmware. In firmware, this will help to detect
Enterprise auth as part of connection and prioritize
the WLAN connection over BT traffic accordingly.
Change-Id: I6463dacbba098c76e6c3b7f4722915797bee1a99
CRs-Fixed: 2848392
Firmware has added TWT nudge, All TWT and TWT stats support.
This feature capability is advertised by firmware in service
ready. Add support fetch and store this information.
Change-Id: Ife3f9e4fbebd5e971c512115d924535a84bf82e6
CRs-Fixed: 2854129
Add new API to handle the logic of sending the WMI command,
WMI_SET_TPC_POWER_CMDID. Create the struct to hold this new
transmit power information.
Change-Id: Ibc7c6109176577f56d149baf87022de557e84445
CRs-fixed: 2841781
Register the event handler for new WMI event,
WMI_REG_CHAN_LIST_CC_EXT_EVENTID. Extract the parameters to be used when
building the channel lists in the regulatory component. Update the reg
rule parsing function to include the new PSD flag and PSD power levels.
Change-Id: I0f5a747f98e43ac3d43b4aa1fb5958f0eac69a9d
CRs-fixed: 2843793
