In cases where one of the interfaces is a P2P-GO and
IPA has been enabled, the P2P connection establishment
fails.
When IPA is enabled, the REO destination is changed to REO4
which can be reaped only by IPA module. But in case of P2P-GO
interface in operation, this change in configuration causes
all the RX packets to be stalled due to incorrect REO configuration.
Hence, to avoid this case, do not change the REO dest config
when the interface subtype is P2P.
CRs-Fixed: 2498315
Change-Id: Ie9f01c3b353c7c0503e1541d6c79c2f47c9782f3
Process smart antenna fields from tlv
HTT_PPDU_STATS_USR_COMPLTN_COMMON_TLV in tx
completion path and export it to tx_completion.
Change-Id: If14e711b0aee8e583fd329f3c3915904649ffe47
CRs-Fixed: 2491429
Since tx_monitor mode and rx_monitor mode consume signficant MIPS
when enabled on a per-peer basis, new requirement is to enable such
functionality on a per-peer basis. New CDP APIs are added to set these
per-peer parameters.
CRs-Fixed: 2494471
Change-Id: Ib44845ec98481cc4df36c30f47335522e5274568
In case of TCP packets being processed by dp_rx_process, send out GRO
flush indication to the thread.
CRs-Fixed: 2500152
Change-Id: I4f464456d423e4680955992c0acf0ed5f4e618b8
Read extra bits of fcs okay bit map from
RX_PPDU_END_USER_STATS_EXT TLV and use the same
to send first fcs okay packet in case of M COPY
CRs-Fixed: 2499150
Change-Id: I1a25971ea789dd7fddddb312af8a18a4cccdc178
Tags are programmed using wlanconfig commands. Rx IPv4/v6
TCP/UDP packets matching a 5-tuple are tagged using HawkeyeV2 hardware.
Tags are populated in the skb->cb in the REO/exception/monitor data
path and sent to upper stack
CRs-Fixed: 2502311
Change-Id: I7c999e75fab43b6ecb6f9d9fd4b0351f0b9cfda8
1. Remove vlan tag in tx and enqueue to hardware.
2. Add vlan tag in rx after peer-vlan_id lookup.
Change-Id: I932202540ac03cabdd20ffd4849fe759ea8a7abb
Update rx error stats. It is a summation of below failures:
- desc_alloc_failure [No free desc available]
- csum error [IP/TCP_UDP]
These failure stats are updated at pdev level and no need
to aggregate this.Directly add at pdev level and export.
Change-Id: I0a5fa8f972babf092163f3cb2d0093547ded4877
CRs-Fixed: 2496037
Add code to remove void pointer usage for hif_handle
and use opaque pointer hif_opaque_softc and also use
cdp_soc for opaque DP soc handle
Change-Id: I2896f7704ffb809214c5b08756c4b8673307fd9e
CRs-Fixed: 2487247
Make change to remove usage of void pointers for
ctrl psoc in DP and instead use a opaque pointer
struct cdp_ctrl_objmgr_psoc.
Change-Id: I9fac21db1156378fc10b95cf10517afa4364da00
CRs-Fixed: 2484411
Add code to use cdp_vdev instead of void pointer for
API dp_tx_send_exception and dp_tx_send_mesh
Change-Id: I63ca5a62c2a8cd6feb906181702888814650dfce
CRs-Fixed: 2480836
Add new CDP API cdp_register_rx_mic_error_ind_handler to
register rx mic error callback. Also, define new structure
cdp_rx_mic_err_info for holding MIC error information.
Change-Id: I4d5d6426b1d5f04848afd48f6dbf51edba291a20
CRs-Fixed: 2488424
fix memory leak issue in tx mgmt ctrl payload tlv.
if any of the mgmt or pkt capture feature is turned on.
htt_t2h_msg is hold in mgmt_buf and not set to NULL on free.
which cause leaking next target to host nbuf.
Change-Id: I0d9e0194e51a21b348aadf747b8c9def5c245eda
Add feature flags DP_FLOW_CTL for DP flowctl ops,
DP_PEER_SUPPORT_OPS to support peer handling in DP,
DP_POWER_SAVE for power saving ops in DP, DP_CON_MON DP_MOB_DEFS
DP_INVALID_PEER_ASSERT DP_PRINT_NO_CONSOLE and DP_INTR_POLL_BOTH.
Change-Id: I01dafadf6578c0b5f36ab3ef56624912fb66b100
CRs-Fixed: 2467170
Read rssi_chain per nss per bw and from rx status TLVs
and update to host data structures.
CRs-Fixed: 2445933
Change-Id: I275e9e502a0a724410fc189ac293cadc8f2981e0
Identify the WIN/MCC specific features. Move the features under feature
specific flags. Get rid of WIN/MCC specific code.
Change-Id: Iaf4e5befd7d574a20bea5c078201adbeac3b762c
The following changes are made
-Yield dp_rx_process if poll time exceeds
-Yield dp_tx_comp_handler if poll time exceeds
-Interrupt statistics to track various interrupt contexts and
corresponding interrupt masks
-Add poll times histogram buckets to NAPI stats
Change-Id: I8c7a6bbbb97c7b3dd1dde6ac3a97113c433086a2
CRs-Fixed: 2423879
Currently there is no support to update tx stats for
non-qos frame. Update tx stats for non-qos data frames
Change-Id: Ib61dd6e3b0c676b5af806c4b1e5cca22ea6ffaa5
CRs-Fixed: 2421925
Add support to measure interrupt latencies, store them
in different "bins" and display the constructed histogram
through user command.
Change-Id: I268be6b39745d550ac7db5d321c2d1fdb2d17d41
CRs-Fixed: 2365812
Increase the maximum allowed OFDMA users to 37
from previously set 8, in cases where more than
8 clients are connected and the PPDU has information
for multiple users like in Trigger frames.
Change-Id: I6b0b9092674514c831694457fc71e68fee512e1f
To avoid using qcacld code in cmn, when getting
wlan op mode, using op mode info from vdev rather
adapter.
Change-Id: Ida5a7aa6c793e955122a4bbf3bf0fa1fa5cbf7a3
CRs-Fixed: 2412317
Delay counters per TID have been implemented for following types:
1. Linux stack to hw enqueue delay
2. HW enqueue delay to tx completion delay
3. TX interframe delay
4. RX interframe delay
5. RX frame delay from ring reap to networking stack
Change-Id: I836596cbd878a43955c18b4981cb5b7b43d4df5e
Check for completion status of the ppdu based on
HTT_PPDU_STATS_USR_COMMON_TLV and
HTT_PPDU_STATS_USR_COMPLTN_ACK_BA_STATUS_TLV.
Update the stats only when completion status is ok else
update retry and failed frames count.
Change-Id: Iac7730715f853746d77873488b7886e7beed467d
CRs-Fixed: 2390383
VOW stats is an extension of regular stats to capture
all drops per TID. Delay counters per TID are also
included.
Change-Id: If6087f37b32cf9ae4bb405190a358ad3c9750dd2
Change API signature for dp_getrateindex to populate rate index
and add additional stats required for RDK.
Add QDF abstraction for EWMA average rssi
CRs-Fixed: 2397918
Change-Id: Id878971799c5df2ae60057a86b2769724ee0dcc5
populate TX OFDMA and TX MU MIMO information from
user rate tlv and display the same in fc_peer_stats.
Change-Id: If1dab15bbdf391fba00a701abd6024c420d1d8f7
Change the CDP abstraction APIs for ast entry find, add and delete
to avoid external references for ast entry in upper layers
Process the HTT v2 peer map messages which will be enabled for
nexthop ast entries and use these messages instead of WMI event
for HKv1 WAR where we have to wait for delete confirmation from
target event which is processed in control path
Change-Id: Ifa91a259c0762344deb8ab89e868fc5554d75543
CRs-fixed: 2354951
Packetdump invokes legacy data path API directly without
considering underlying HW:
1. ol_register_packetdump_callback
2. ol_deregister_packetdump_callback
Global pointer pdev_txrx_ctx will be casted to struct ol_txrx_pdev_t
always even Lithium (use struct dp_pdev) underlying, that leads to
struct dp_pdev be overwritten unexpectly.
Wrap with cdp API to avoid.
About packet-dump feature:
It is one debug feature/requirement for Android N, to track/dump
TX/RX data/mgmt. packets during connection. This enhancement can help
in debugging connection related issues.
This change only touches its data packet callback register API.
Change-Id: Ie63fd2dfa909f89741ccf0c5131f6d3305093a3e
CRs-Fixed: 2366334
Add support for GRO functionality for TCP packets.
- Pass GRO config to DP layer as a part of dp_update_config_parameters
- Add API to read the number of active RX contexts from DP layer
cdp_get_num_rx_contexts
- Fill GRO info into skb->cb from rx_tlv during dp_rx_process
CRs-Fixed: 2346995
Change-Id: I1c143d8ce2c7522ba2c76142fb6cc82193df5608
Change max OL_TXRX_NUM_LOCAL_PEER_IDS to 35 to take care of
STA + SAP + P2P concurrency.
Each AP will occupy one ID, so it will occupy 2 IDs for AP-AP mode.
Clients will be assigned max 32 IDs and STA(associated)/
P2P DEV(self-PEER) will get one ID.
Change-Id: I4d3e74c550e34b1d3417825245990655ead87b28
CRs-Fixed: 2356032
Add new flags for MEC and DA enable/disable
and keep it independent of WDS enable flag
Change-Id: Idb49c45ebb34a38f876dbdb293806c4e96d49b5d
CRs-Fixed: 2336332
Add iwpriv <interface> txrx_stats 29 and
iwpriv <interface> txrx_stats 30 to print wlan_cfg
parameters for both soc and pdev.
Change-Id: I666fe4fa999e82e92ea2961ab662e3e629b58bc7
CRs-Fixed: 2331949
Rx ppdu_type_str displays incorrect ppdu type in
data_txstats output. Change ppdu_type bit length from 2 to 5
to support all types.
Change-Id: I5441140b0d90896c296c8f61d5863e711da95149
CRs-Fixed: 2330614
- Support to pass IPA enabled(disabled) flag from ini to DP layer
- Use ioremap call to translate tx_comp_doorbell_paddr obtained from
calling ipa_setup api to tx_comp_doorbell_vaddr. This is needed to
write the initial value of HP at the doorbell address.
- Change REO_DST_RING_SIZE and WLAN_CFG_TX_RING_SIZE to 1023
for napier/hastings if IPA is enabled. This is needed because,
ipa_setup API can handle only 16-bit values for the size param(bytes)
of the ring.
- Disable hash based flow steering for SAP peers in case IPA is enabled
and set default reo_dest_ring_4 as default RX ring. Since IPA will be
reaping RX packets from reo_dest_ring_4 only, flow steering is not
needed for SAP peers.
- Unmap pre-allocated TX buffers for IPA in the TX completion ring.
- Donot execute IPA functionality if IPA is disabled from ini.
Change-Id: I6855bfe293a457ccc0abd1ad5567f5c95232a9d2
CRs-Fixed: 2183519
