Currently the driver uses the API
policy_mgr_is_dbs_enable to check
whether the DBS is enable or not which
does not check the service capability of
DBS, and thus would return true if ini
and FW HW modes contain DBS. In this case
if STA is on 5ghz and SAP comes on 2.4ghz
then force SCC would not happen as the
driver would consider the HW to be DBS
capable which actually is not, and thus
the overall concurrency would be MCC which
is not favourable.
Fix is to use policy_mgr_is_hw_dbs_capable
API instead of DBS enable API which checks
for the service bit also, so that the driver
forces SAP to STA's channel.
Change-Id: I9319293ecfb54fe3e1ad0eaff15542c671514bf4
CRs-Fixed: 2820377
Currently the driver checks whether hw is
already in DBS in the function
policy_mgr_check_and_set_hw_mode_for_channel_switch
and it does not set hw mode if it is already
in DBS mode. It can happen that SMM is already
requested and is present in serialization and it
would change the HW mode from DBS->SMM and if
driver starts any vdev on 2.4ghz in HST/HSP
which requires the DBS mode for 2.4ghz , the FW
would send a vdev start failure.
Fix is to remove the check of current hw mode and
let DBS be posted to serialization. If hw mode is
already in DBS it would return from serialization
with E_ALREADY but would ensure that HW mode is
always in DBS for a 2.4ghz connection.
Change-Id: Ica660058175cb1edc2931dd2d28ee6cdd9bab2f4
CRs-Fixed: 2823238
Currently, there is no INI parameter to control NAN feature in 6GHz
frequency band. Because of this, there is no provision to disable the
NAN in 6GHz when there is no requirement.
To address this, add INI parameter to configure NAN feature in 6GHz.
Change-Id: I6b4faa8e8aa1a3df72539fed1d7ff3cc8287debd
CRs-Fixed: 2817920
Use WMI_RX_SERIALIZER_CTX context for thermal event handler.
The default context is tasklet, it may cause issue when interact
with OS interface.
Change-Id: I349412c2afee9a081f0d38704541f77b5e4569f4
CRs-Fixed: 2824461
IPA MCC work is initialiazed only when uc code loaded successfully,
before canceling MCC work check for uc load success state.
Change-Id: I9af501d1b974d0da21891634bde2beafd69701b2
CRs-Fixed: 2822382
Firmware sends peer create confirmation to detect duplicate peer
on other vdev. If the status field in the
wmi_peer_create_conf_event_fixed_param is 0, peer creation is
successful.
Add support to handle the peer create confirmation command for
sta mode. For roaming scenario, the peer will be internally
created by the firmware, so bail out after creating object
manager peer/datapath peer without sending the peer create
command similar as the current implementation.
For SAP/P2P Go mode the legacy peer create path will be used.
Proceed to do post linkstate change if status is success, else
do vdev stop and indicate failure to upper layers
Change-Id: I0abbd70dd509f2b9afa8d4d7db1774e289d1e021
CRs-Fixed: 2747870
Add a check for passive channels when checking the restricted
bands on SAP. This change blocks SAP from restarting on a passive
channel.
Implement the function to filter out passive channels from the PCL.
Change-Id: I80a4b78c1af77f5bfa68be3163f9e9a78cc6425a
CRs-fixed: 2817589
Modify connect start code in interface manager by
moving disable roam and tdls link teardown notify
APIs from HDD to if mgr. Alongside, move tdls link
teardown notify API from HDD to if mgr in start bss API.
Also, move the tdls link teardown API to TDLS module from
HDD module as TDLS should manage the wait logic.
Change-Id: I09fa31878563a3daaa7c5fde46327475829317b3
CRs-Fixed: 2811807
Add new ini "monitor_mode_concurrency" to support this feature
and introduce policy manager api's for concurrency checks.
Change-Id: I35ee1fece0a6f9ae8fe340b0598c4a3e20b17e82
CRs-Fixed: 2814523
In mission mode, add support for virtual add/del monitor
mode interface. In addition to STA vdev, create and maintain
a new vdev for monitor interface.
Change-Id: I91ea8e56976cce92f9b1ae308d4bd0fb30815366
CRs-Fixed: 2818499
On some third party platform, the in-band bus suspend-resume is
not supported well, instead add gpio irq as wakeup source to
support out-of-band suspend-resume.
Change-Id: I7621f04d093013e15719b5c84dc244604be238df
CRs-Fixed: 2815754
Check the factors as below to decide whether the channel is
allowed or not:
* If the channel is in LTE coex channel avoidance list;
* If it's STA+SAP SCC;
* If STA+SAP SCC on LTE coex channel is allowed.
Replace policy_mgr_is_safe_channel() with this new function
for sap channel selection and acs channel filtering, to allow
unsafe channels when it's STA+SAP SCC and STA+SAP SCC on LTE
coex channel is allowed.
CRs-Fixed: 2743042
Change-Id: Ic5a84b2628200fe9decf6972f00706f190f04722
Add logic to
- Check if connect req freq is 6Ghz and security
is not allowed for 6Ghz, reject connect.
- Ignore 6Ghz APs if connect req security is invalid
for 6Ghz
Also added user config key_mgmt_mask_6ghz mask
to allow specific AKMs, by default all are allowed.
Add added user config check_6Ghz_security to enable
security checks as per spec.
Change-Id: Iada7bb685b272e26cff7e89cf64d181ed6eb48a4
CRs-Fixed: 2820358
cds_get_context() function already takes care of logging the
caller function name in case of any error.
Hence there is no need to add the error log again.
Getting rid of these unnecessary logs reduces driver memory footprint.
Change-Id: I5bf676c79e9e12a797dc6792ee8014fb30b0dff3
CRs-Fixed: 2821005
The SHO feature is used to offload beacon/probe response to HW.
So a new vdev param is required to enable/disable this feature.
Change-Id: I83d71d63485dee8d3433bf967a7feb56c1039f93
CRs-Fixed: 2815270
Add check in function 'policy_mgr_get_sbs_channels' to restrict the
array index out of bounds.
Change-Id: I387b666095107faf284e35f073dfe856d38323d3
CRs-Fixed: 2776966
A race condition is observed when runtime suspend is aborted
due to pending TX packets but context switch happened and pm_state
did not revert to active state yet. In parallel, WMI_PEER_DELETE
command is queued but not sent as pm_state is still in suspending
state.
To fix this, schedule HTC queue kicker work to resend pending
commands again after dp_runtime_suspend aborts due
to pending TX packets.
Change-Id: I6d2c4140a4635c0aec304f48b15fb2b539ac39ea
CRs-Fixed: 2813657
In case of STA + SAP/GO, Driver fist disable roaming on all
adapters before bss start and enable roaming after start bss
(SAP/GO) in case of failure/success.
Due to commit I4870c69a0e0ca1e8cad734a591f09e402b7a32fa,
Driver fails to re-enable roaming after failure/success
of SAP/GO process.
Fix is to enable roaming after start bss in case of
failure/success.
Change-Id: Ibe90f0685f41984a5841859ea96834f7760ff9a1
CRs-Fixed: 2811306
The event WMI_ROAM_STATS_EVENTID is received after
every roam, once the roam synch complete is sent by the host.
This event contains details regarding the btm response.
This helps to debug the scenario when roam failure happen.
Print the info received related to roam scan type & roam status
info into kmsg.
Change-Id: Idd688eb4d1e699573fa1e243873c30ffdc5bf96f
CRs-Fixed: 2794555
Previously, if STA is connected to DFS channel and SAP starts on
Non-DBS HW, then it is forced to start on DFS channel with BW 160 Mhz
irrespective of BW on which STA is connected without CAC.
Even after STA disconnects, SAP remains on DFS channel with BW 160Mhz.
So, scan will be disabled and STA cannot be connected on any channel
other than DFS channel.
If STA is connected on non-DFS channel on 5 GHz and SAP starts, it
will start on non-DFS channel as primary channel with BW 160 Mhz
without CAC. Also, scanning was also allowed when SAP is started with
BW 160 Mhz. This might violate regulatory in case radar comes up while
scanning.
Standalone SAP on DFS channel was not allowed.
To fix this, Force set SCC for non-dbs HW, this way standalone SAP
can come on DFS channel but scan will be disabled in such case and
STA cannot be connected other than DFS channel.
In case STA gets connected to dfs channel in non-dbs HW, then sap
starts only on STA channel with force SCC with BW
MIN(sta_chan_width, CH_WIDTH_80MHZ).
Afterwards, if STA disconnects, restart the AP with BW CH_WIDTH_80MHZ
on safe channel. Scan will be allowed as the DFS master capability is
offloaded to AP with which STA is connected on DFS channel.
Also, if standalone sap starts, then STA connects to DFS channel then
SAP will restart with STA channel frequency and Channel width
MIN(sta_chan_width, 80MHZ).
If standalone SAP starts and then STA connects to non-dfs AP or SAP
starts when STA is already connected to non-DFS AP, then ch_width is
MAX(sta_chan_width, 80MHZ) (5 Ghz) or 20 Mhz (2.4 Ghz).
If STA disconnects during SAP+STA on non-DFS, SAP won't restart unless
the STA was connected on BW 160 Mhz.
Change-Id: I1cebfc79f170c1e4e2710ed747ec804df3d8b441
CRs-Fixed: 2809255
Add an INI to configure the wow-mode logging config.
So that,the fw would use this bitmap for logging when it
is in wow mode.
Change-Id: Ib2fbd0c5c9cc573b2f5b12dcdf06682c16550cb2
CRs-Fixed: 2810372
Rename struct wlan_cm_connect_rsp to wlan_cm_connect_resp for
better readability and to avoid duplication of the structure
and function name as there is already a function with the same
name.
Change-Id: I331365058ed25b902aae11f979512b4edcd3ac06
CRs-Fixed: 2809137
Move ini CFG_VENDOR_ROAM_SCORE_ALGORITHM from qcacld-3.0 to qcacmn part.
from qcacld-3.0: mac_ctx->mlme_cfg->roam_scoring
to qcacmn: mlme_psoc_obj->psoc_cfg.score_config.
Change-Id: I318f0d516ce699c061f268116e1cbf79fcc9e23a
CRs-Fixed: 2806090
Since new rso ROAM_OFFLOAD_V1 path is enabled, remove
the old rso path code for cm/wmi roam related files.
Change-Id: Iec350f032c3e037204f560199d4a6e258ac02688
CRs-Fixed: 2810145
Roaming between different PMF option APs has following issues:
1. Roaming between Optional -> Disabled -> Optional
When STA roam to optional, PMF is set to False from STA in reassoc
request and all management pkt not secured.
2. Roaming between Required -> Disabled -> Required
STA not able to find candidate AP when tried to roam to AP with PMF
Required.
Root cause: When LFR3 roam happens, vdev_crypto_params will be reset
including rsn_caps 11w PMF, if new AP hasn't enabled PMF, vdev rsn_caps
11w PMF is disabled too, and passed to F/W. Then F/W think DUT STA
doesn'tsupport PMF, then failed to roam to AP with PMF Required and
enabled.
Fix:
Get self-capability of 11w PMF from connected profile and pass to F/W in
WMI_ROAM_SCAN_MODE by wmi_fill_rso_tlvs after roaming.
Move target_if_cm_roam_fill_11w_params to csr_cm_roam_fill_11w_params,
put protocol part to csr connection manager.
Change-Id: I543799385ec8c0ec7afdf64e2310c24758305095
CRs-Fixed: 2807454
Memory is created for the mlme legacy pointer during the create
of the mlme legacy priv object. This allocated memory doesn't get
free when an error condition which leads to device crash.
To avoid this problem memory should be freed before returning from
the error condition.
Change-Id: I8aaaf7bf17cf38f70135e5ff00db429c34aff2d8
CRs-Fixed: 2803896
Use separate hang reason for case that lack of credit after suspend.
Meanwhile add hang buf offset check to avoid overflow.
Change-Id: Ic794d02672cd663598da66b9e75924c41b5ef0e8
CRs-Fixed: 2801343
Move the logic to get HT and VHT caps in LIM from CSR also store
VHT and HT caps in vdev mlme instead of csr session.
Change-Id: I29b8e836a79a4a9eda5088c0eb2e0bf48d616de2
CRs-Fixed: 2807209
In the scenario where IPA UC ready work is processed after
wlan_ipa_uc_ol_deinit, triggered as part of idle shutdown,
there is a possibility for NULL wbm srng pointer derefernce
when setting the tx doorbell address.
Fix is to avoid scheduling UC op work when deinit is in
progress.
Change-Id: Ifa0908912b77f45b7d93c5f9c2f5aaf9e17685c5
CRs-Fixed: 2807218
Disable IPA when second SAP is turned on only if NAPI support
is enabled for IPA path.
Change-Id: Id30714156a959ed940d0480cb0e0d8db467c821f
CRs-Fixed: 2807158
Stats event from target might have several sub events, and some event
has no peer stats but have adv/ext2 peer stats.
Check ext/ext2 peer stats even no peer stats in
target_if_cp_stats_extract_peer_stats(). Fix copy adv stats size error
in tgt_mc_cp_stats_prepare_n_send_raw_station_stats(). Although
get_station_stats_cb and get_peer_stats_cb is union callbacks,
better to assign to get_station_stats_cb because it is for
TYPE_STATION_STATS.
Change-Id: I0bead0cbb8b549cc538ef4a7327f0a8303c90bd1
CRs-Fixed: 2801842
Currently pmo_psoc_get_vdev api just returns the vdev without
taking the vdev reference and it is caller's responsibility to
take the reference, there could be a race condition where after
getting the vdev and before getting the reference of that vdev,
some other thread may delete this vdev.
To avoid this issue use objmgr api to get the vdev for pmo.
Change-Id: I3495589e2dbbb7d8efc579a62fff1a08a92c318f
CRs-Fixed: 2771211
Add support for connect and disconnect path
in legacy cld files with respect to connection
manager.
Change-Id: Ia42dd45d943de20d91279c0197b0f17a5c0326eb
CRs-Fixed: 2805807
In DBS mode, gDualMacFeatureDisable can be 0, also can be
6: enable DBS for connection but disable simultaneous scan.
Change-Id: Ia3d46dbd2e67644e84436b90f40c203bc939eda7
CRs-Fixed: 2807010
Add a new action OUI to disable TWT for certain APs.
The cfg item will be present in the host and sent to
the FW to disable TWT.
Change-Id: I122c44993a9102838dec7e9eb2817ba404a76515
CRs-Fixed: 2793124
Host adds support to send enable/disable wfa config for FILS_DISCV_FRAMES
to firmware.
Change-Id: I0143b158b5f62b42c0d4c3d8a34a7ec7b1ec994b
CRs-Fixed: 2801144
Handle firmware thermal stats event and populate the thermal
information to upper layer with vendor command event.
Change-Id: I83286367ab542c08a205a7636f3d03189b0500e5
CRs-Fixed: 2786623
Change return type of following APIs from int to QDF_STATUS.
wmi_unified_register_event()
wmi_unified_register_event_handler()
wmi_unified_register_raw_event_handler()
wmi_unified_unregister_event()
wmi_unified_unregister_event_handler()
Change-Id: I534b499edbcfec6eddea0e9ed48f9eb1a2e872c8
CRs-Fixed: 2791275
NDP connection will be active for keep alive period even after receiving
NDP end request. The default value for this keep alive period if 20ms.
update the default value as 14ms to reduce the wait time for connection
termination.
Change-Id: I3d09ce764846d7e535a7369d32a730907b621735
CRs-Fixed: 2802723
INI he_twt_requestor and he_twt_responder should be able to disable/enable
twt requestor and twt responder.
Make them work.
Change-Id: I5e091a2f04cca1817f1a2db6358f141c2eaf103d
CRs-Fixed: 2798800
Host is not enabling WTC_BTM roam trigger via
roam_enable trigger command
(WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID). Because
of this roam scan is not triggered and BTM response is
not sent to AP.
Fix is to enable WTC BTM by default
Change-Id: Ie33f8a298818955c886094d6f703b9603ab5b00e
CRs-Fixed: 2795665
In Interface manager, legacy roaming api's were used as roaming testing
was ongoing.Now testing is done so use converged roaming api's.
This will also resolve the KW warnings.
Change-Id: I9ef101e6ec02bb18c6f2f9a9fbdaa81dbe81f9a0
CRs-Fixed: 2798601
To discard 5G candidates based on RSSI threshold, Introduce
a new INI "min_rssi_for_2g_to_5g_roam" to configure the RSSI
for High RSSI Trigger.
Min: -120
Max: 0
Default: -70
Change-Id: If4545296ef1b53d18b8ae4abf12d450f5e690240
CRs-Fixed: 2789017
