If PMKID present in AP expires, AP rejects the PMKID based association.
Current design is to clear the cache using BSSID/MAC address of link
in such cases to let a fresh SAE authentication to happen.
But host driver stores PMKSA with MLD address for ML BSS.
Adapt to the same and update PMKSA cache clear APIs to use
MLD address instead of link address.
Introduce new API which return the legacy address for non-ML
association and MLD address for MLO association of the BSS peer.
Use this API to get the correct entry from PMKSA cache to delete.
Introduce new utility API to fetch the MLD address from scan entry.
Use this API to get the MLD address of the ML candidate.
Change-Id: Id35a3937ba6649e8ba7ae8f849ac1ed2a9cc83f8
CRs-Fixed: 3453839
With the MBSSID IE, it has to generate the corresponding
beacon and probe response frames. Then handle the generated
frames per critical update feature.
Change-Id: Iff3fdb3a335a98d9ed7e51957885e2f161069807
CRs-Fixed: 3376521
Currently, if ACS_LAST_SCAN_AGEOUT_TIME is not provided by user then
the last_scan_ageout_time is updated to 0 and full scan is triggered
to find channel instead of using previous scan results, to avoid delay
use last full scan result based on ini "last_scan_ageout_time" value.
Change-Id: Ic38f0d3c83087dafde54b43762dd14deb7d02870
CRs-Fixed: 3404550
Changes to handle dynamic link add for non-AP MLD.
Also add change to clear mlo cap for link removal of vdev.
Change-Id: I47e0bb77b7f32296e5745ffd53ce3a34ec35a63a
CRs-Fixed: 3346538
Fetch beacon/probe response with given mac address from scan db.
The frame can be used to fill bss descriptor in case of MLO
roaming where scan entry is derived from ML probe response of
assoc link.
Change-Id: Ie20b36c6619dd0e44d04d3bd8767c7dd09b053d5
CRs-Fixed: 3342439
Low latency SAP can come up on below two profile
a. Gaming
b. Lossless Audio
Scenario: LL SAP is present on 5 GHz channel and scan comes up
DBS: For both profile, allow scan only in 2.4 GHz channel
SBS: For both profile, allow scan on non low latency SAP
channel which are mutually exclusive.
Change-Id: I9d5832a457d08325b9e66099286ae3f18cdc66e1
CRs-Fixed: 3294607
Based on the new requirement, add support to get requested
feature set info from different feature components.
Change-Id: I75c5a3062312b1124d21d1ae429a7c5a18d9f2d0
CRs-Fixed: 3262867
Currently STA can scan and come up on 6Ghz or indoor channel if
hardware is non-dbs and SAP is present
As part of this change, do not allow STA to scan on 6Ghz or
5Ghz indoor channel for non-dbs hardware if SAP is present
Change-Id: I97759f8b2c6a1c460d90fbb797a0e64d2532797c
CRs-Fixed: 3186406
There is an API to get the scan aging time,
but there in no API to set the scan aging time
and can be configured through INI.
Add API to set the scan aging time run time.
CRs-Fixed: 2894428
Change-Id: Ide2b2eec780dd7ff07ebd783b0916a68c0e94a2c
Adds wlan_scan_get_scan_id, wlan_scan_init_default_params,
wlan_scan_register_requester and wlan_scan_unregister_requester
APIs to use from non-osif component, as ucfg_* API should only
be used from OSIF.
Change-Id: Ia90313030e853c957ca85e47ff2b67097490ef87
CRs-Fixed: 2791549
Currently, there is no provision for dynamic dwell time control in 6G.
Update existing driver commands SETDWELLTIME and GETDWELLTIME to
support 6G.
Change-Id: Id284097e300f3ed45557ebe7ea2287e0da9a485b
CRs-Fixed: 2789720
Adds wlan_scan_start and wlan_scan_cancel public APIs to use
from non-osif component, as ucfg_* API should only be used from
OSIF.
Change-Id: If603e49a57641dba26163454bce12327660b20fd
CRs-Fixed: 2773612
The driver doesn't ageout connected BSS from rrm scan
result after the scan default ageout time. This results
in connected AP information sent in beacon report request
in table mode always.
Introduce scan api to get the scan age out time configured
from scan module. This value will be used as the threshold
in rrm scan filter.
Change-Id: Ib3981538faf179cff53936770f705d41922dca66
CRs-Fixed: 2650914
Currently there is no support to dynamically set dwell time
for 2g channels.
Add support in existing command SETDWELLTIME to dynamically
configure dwell time for 2g channels.
Along with set, add support to get dwell time for 2g channels
with the existing driver command GETDWELLTIME.
Change-Id: I8a71e39338e7a81690140f50bc3c5ac7b0bd63eb
CRs-Fixed: 2620370
Currently dwell time is determined by scan policy flags from kernel.
Sometimes when we suspect the scan result is not full enough, we need
to set dwell time by force through ini.
Add ini to decide whether to honour NL80211 scan policy flags, so that
we can disable dwell time changed by scan policy flag from kernel.
Change-Id: Ia0b9f957a7de901513479522e008e4bcbd6b2c0e
CRs-Fixed: 2428630
Add an API to add scan entry without posting it to scheduler thread.
This will be used to update the beacon/probe during roaming to new AP.
Change-Id: Ia53ba194032eb953c5b102b0cc406db12e58f42d
CRs-Fixed: 2435404
Currently the driver includes all the DFS channels as part of scan
in the scan list, and thus not exclude the DFS channels in the first
scan for faster scan.
Fix is to check the ini, for first DFS channel scan, and then remove
the DFS channels from the scan list if the ini is enabled.
Change-Id: I43d5c87676d4e66706da3cc0029c60559b70d179
CRs-Fixed: 2378805
Create ucfg apis in scan components for calling from hdd.
Move the scan apis to new file, wlan_scan_api.c
Change-Id: Iec08eddbba3066a4d781c988624d47749a75610a
CRs-Fixed: 2342892
