Add qdf wrapper for dma_clean_range and avoid use of DMA
map/unmap APIs in Tx. simple fast path.
Gain of ~150 Mbps is observed while running 4 radio traffic.
Change-Id: I0e96bfee43fe810da8c861cb0f4535fb0ba7f6f7
DMA unmap for scatter gather packets is done using
only frag0 dma address and the entire packet length
which will lead to incorrect behaviors. Add handling
to do dma unmap for all the fragments of SG packets.
Change-Id: I614553d9f96c573f0095c9be38706fd4ac3223ab
CRs-Fixed: 3112424
Tx descriptor is not being freed and put back in tx desc
pool for a long time. As a result, system is not going
into suspended state.
To find this descriptor, during dp_bus_suspend and
dp_runtime_suspend, parse through the descriptor pool to
check for any descriptors not freed for a long and trigger
self recovery when found.
Change-Id: Id97c5c8537c9bec922f4e254b5bf094505ee61ff
CRs-Fixed: 3109868
The following issues are fixed with this change-
1. Sojourn stats were printing incorrect values
2. RSSI values were junk numbers
Change-Id: Ibed73cf370a309bf9db5baad37a0e8261c58463b
Prefetch TX HW desc, SW desc and SKB in pipeline fashion in Tx.
completion path.
This improves the UDP DL CPU idle% by ~4.5%
Change-Id: I48096e996cd835321ce2681d3981fa94c7189f54
Customer reported their HLOS LTE-WLAN transition algo sometimes go wrong
for wrong low layer stats, Txretry delta is bigger than Txtotal delta.
Txretry unit is msdu while Txtotal unit is mpdu.
Add vdev/peer stats for mpdu number of successfully transmitted after
more than one retransmission attempt, to align mpdu tx_packets, tx_failed.
CRs-Fixed: 3099490
Change-Id: Id4b9d8fd81af4bf0c141dad481bfd2b3f6c1db2a
Multicast support for MLO
1. Following functions are newly added.
dp_rx_igmp_handler()
dp_tx_mlo_mcast_handler_be()
dp_rx_mlo_mcast_handler_be()
dp_mlo_get_mcast_primary_vdev()
Change-Id: If215f843369e6e2621ef302b924e524c86f0d30b
In SAP mode, intrabss forwarding can happen when system
suspend is in progress. This could potentially result in
a scenario where SW2TCL HP update goes through after
WOW_ENABLE command is sent to FW.
Fix is to check for system PM states and do an explicit
system wakeup if tx packet gets enqueued to SW2TCL after
wow is enabled. Flush the SW2TCL HP on system resume.
Change-Id: I8dcd108b0dc1d703168f2f7a0ef0627e4dc0b103
CRs-Fixed: 3087727
Use the tracepoints to trace delayed register write, ce
tasklet scheduling latency, tx, and rx packets.
Change-Id: I63a89276177a9d0466dcb0c831eeb8e938a2bf79
CRs-Fixed: 3081870
tso_desc is assigned to msdu_ext_desc in dp_tx_prepare_desc
for TSO packet even before msdu_ext_desc is configured which
could result in NULL pointer dereference.
Fix is to set the tso_desc and tso_num_desc in msdu_ext_desc
post dp_tx_prepare_ext_desc.
Change-Id: I62279c94ea7037b3f6a92644ae7eb6a5e63631f6
CRs-Fixed: 3083846
Following peer stats are updated in per packet Tx completion path:
comp_pkt: Pkt Info for which completions were received
tx_failed: Total Tx failure
In BE architecture, HW provides the support for basic vdev stats and
hence per packet stats updation of above parameters can be done only
when enhanced stats is enabled or HW vdev offload stats is disabled.
Avoiding per packet stats updation reduces CPU load and improves KPI.
Change-Id: I7090d1a1ce0a882236e3310e3e9517149cbb146b
CRs-Fixed: 3067843
CCE disable was done for 8074 V1 specifically which is no longer
needed for future releases and hence removing CCE check in TX.
per packet path
Change-Id: Ia31c5e2cb181e4a3409fa1f1abce8c55524b1b05
Check of Invalid QOS tag which can be set for non-mscs clients
connected on same VAP as MSCS clients. TID override needs to be
avoided for those clients
Change-Id: I651a354e740fe6aee74f94b59ac2e6f154a80c6d
remove the assert when HTT_TX_FW2WBM_TX_STATUS_MEC_NOTIFY
is received and mec_fw_offload is enabled.
Change-Id: I1b9c876822e3e9c05b5035af82afa484106e880a
As part of code change we are removing csum_enabled flag check.
In that case, csum_enabled becomes redundant since we are not using it
in the code base, So remove redundant code as part of the cleanup.
Change-Id: Iac411b20f06436053b1969a1af9e3b3ee418c34c
CRs-Fixed: 3070858
Avoid tracing data packets at high throughput levels. This helps save
CPU cycles.
CRs-Fixed: 3059712
Change-Id: Ideca04e142a2f4080cd5758fe27f0b526ea4f9ad
Add timestamps for last TX/RX in peer stats. This stat is needed to be
passed on to upper layers on demand.
CRs-Fixed: 3059712
Change-Id: If0d8b7dc3c139e4d1b670bf98f3f574f02ea9715
Add support to invoke HIF runtime PM APIs in TX packet path based on
throughput level. Essentially at high throughputs, where runtime PM is
not expected to provide power gains, invoking the APIs is deterimental to
performance.
Hence invoke runtime_pm APIs based on throughput level.
CRs-Fixed: 3059712
Change-Id: I49d111bffa8a37c68abbdd54911f9ecc22430562
In case of successful transmission If MPDU tx
is retried more than the threshold then
increment MPDU retry count by transmit_cnt / threshold
Change-Id: Idbc7e2d0579ff68e272132fe4ffe9f951c4aacf5
CRs-Fixed: 3058464
Take care of the MLO peer bit indication to be
concatenated with peer_id to access the peer map
object.
Change-Id: Ia603a728101e83829a8906d1b847f42389e78ca6
CRs-Fixed: 3039326
This change includes below
1) Changes needed to increase Tx rings to 4
2) Use WBM2SW4 ring for rx error in QCN9224
3) memset srng at alloc to avoid populating RBM_id
in per packet path and enable implicit RBM
Change-Id: Icbd5ac2378273b8f3c6adc41c611e29551fff22f
This change is used to provide an API for PMO module to
check whether there are pending TX frames before HOST sends
wake up indication to FW. PMO module uses this to indicate
FW whehter to discard HWDTIM.
Change-Id: Icc3271e87e376e3313fddc5f4f99e39daeaf6af7
CRs-Fixed: 3046947
The multicast echo check feature is moved to hardware in
Beryllium. Enable this hardware feature and also disable
the MEC handing code for Beryllium in the host.
Change-Id: I86d319963191f3ed77aba16dcccbc659906edd9f
wds in Beryllium is managed by hardware.
Make use of hardware managedwds and disable
the corresponding wds handling done in host
for Beryllium.
Change-Id: I39f23cb40c6c5f85ada8ce59c92ff2855bb18da3
Do not populate the struct meta_hdr_s into for buffers received on
Tx completion path when operating in mesh mode.
Also update the fields in tx_capture_hdr as per the new definition.
Change-Id: I6150b4ce891ca73d5ed7c7620568606c377223c6
Dump flow pool stats even for low verbosity level as
part of periodic stats display.
Change-Id: Iea59d20b0a81cfd0bfdac65ad54a11fa33f30f2f
CRs-Fixed: 3031168
WDI event WDI_EVENT_UPDATE_DP_STATS is triggered for updation of peer
stats from both per packet and monitor path wherein per packet path is
applicable for MCC and monitor path is applicable for WIN.
Trigger for this event is flag protected under the macros
FEATURE_PERPKT_INFO and WDI_EVENT_ENABLE.
FEATURE_PERPKT_INFO is not defined for MCC.
With this, WDI event in per packet path is not triggered and hence unused.
Make changes to remove the unused code.
Change-Id: Ibcb0948b0ecae313270b6a173e243b2f27f1bbee
Tx data transfer in host mode with nbuf map_unmap debug frmwk
enabled and enhanced stats disabled results in an assert.
This is because on Tx completion path, nbuf unmap is done using API
qdf_mem_unmap_nbytes_single which takes physical address of nbuf
for unmap and does not remove nbuf from map_unmap tracking list and
when nbuf is freed, it results in assert as the tracking list still
contains that nbuf entry.
In order to fix this, define a new API for nbuf unmap passing physical
and virtual address of nbuf as arguments. Physical address is passed
as an argument in order to avoid cache miss in per packet path which
eventually helps in improving the KPI.
Change-Id: I77ab6ac3ac98556b9caff8aa3ee82bc23cd26de7
CRs-Fixed: 3006671
PATCH[6/7]:
This patch consists following changes:
-Move monitor related pdev variables to struct dp_mon_pdev
-Move monitor relted soc variables to struct dp_mon_soc
-Move cookie to monitor link desc va to monitor file
-Add APIs to access monitor related variables
-Add dummy APIs to build without monitor support.
Change-Id: I032a480b1383d061f984cee3ba6b10ac7a0ff350
CRs-Fixed: 2983781
Add support to calculate uplink delay on a per vdev basis.
The delay calculated excludes bus delays, where packet
enqueueing time and complete time are fetched from HW release
ring.
Change-Id: I4bbcbf28b197f7a87cb822a841f1f957ebcf063b
CRs-Fixed: 2958833
If number of entries available in tx comp ring are more
than quota then process number of entries as per quota
Change-Id: I6345cb6f7cee62c343d152f42beb15460ce02ef1
Move DP TX target specific functionality to dp/wifi3.0/be
and dp/wifi3.0/li folders. DP Functionality common to both lithium and
beryllium targets stays in dp/wifi3.0.
Change-Id: I3497284153e2ea30a9cb1faf05bd41422329b804
CRs-Fixed: 2891038
Memory allocated for tx_hw_desc_history uses incorrect
size parameter resulting in much lower memory to get
assigned. This will result in OOB access and corruptions
in memory, regions post the trailing boundary when updating
tx hw desc events via dp_tx_hw_desc_update_evt.
Fix is to use the appropriate memory size for tx_hw_desc_history
and add NULL check in dp_tx_hw_desc_update_evt.
Change-Id: I97af7898cf8bf1b24978d559f84a2a3d00227ed8
CRs-Fixed: 2952859
In some of the targets modulo operator assembly API's
are not defined causing compilation error.
To avoid this use qdf based API's for modulo operations.
Change-Id: Ibc69b69aa38cadff5daa8dee8b65ceaacfe997b7
CRs-Fixed: 2940281
