When plane is detached from crtc in one atomic commit and then
attached to another crtc in the next atomic commit, the second
plane state swap will happen when the first commit is still running
in the previous crtc's worker thread, which will result in two
threads programming the same plane and run into undeterministic
state.
Fix is to add plane_mask check before state swap, together with
crtc_mask check. This will make sure there is no pending worker
thread working on the same plane.
Change-Id: I64cd4b68fa9746e988d933069ac0f8083d974c79
Signed-off-by: Xiaowen Wu <wxiaowen@codeaurora.org>
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Populate the supported colorspaces property for DP
as part of getting the display modes.
This will expose the supported colorspaces of the sink to
userspace and in-turn the userspace shall pick the colorspace
suitable for the use-case.
Change-Id: I70408c719610bc63f9c06dad8cd50f7fa5d94908
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
This change makes the post PPS command delay a panel property.
By default the value is set to zero if not specified.
Change-Id: I50c86ba0f0cb28ff617435e92e9675e5c35404ca
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Create a data structure to maintain available hardware resources
and track capabilities. This data structure is used to send
the current available resources and caps information to
connector ops get_mode_info, get_modes and validate_mode to
process the display mode.
Change-Id: If38fc628ee5ab4729821f88c0050ab45375187b8
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
This change ports the missing changes from 4.14 to 4.19
that were missed. It includes changes up until
commit 0f8fb25421ff ("cnss2: Add device version to
SOC info structure").
Change-Id: Idfdfe891f146e389e3c65cc3fc4c98d93220e789
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Primary and secondary displays should have first priority
when reserving lms. Static reservation can potentially block
higher resolutions for the required displays. This patch gets
the layer mixer requirement for primary or secondary display
if available. It reserves those layer mixers dynamically
for the respective display when connector is registered.
Change-Id: Id69dac4c72d6b20008049f4aeb71c0f97d0a426b
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
This snapshot ports changes from 4.14 to 4.19 into
the msm and sde layer. Snapshot was taken as of
commit 0f8fb25421ff ("cnss2: Add device version to
SOC info structure").
Change-Id: I59b799a78319c2db6930a2a10bc38976f8c09898
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
DSI display may support video mode and command mode both and it may
support transition between these two modes.
This change adds seamless transition between these two modes for DSI
display by avoiding crtc enable/disable and panel power on/off
during modeset.
Change-Id: Id7ddaef7d1f0f7cc7d52283755bad53a246adec6
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
Add runtime_pm ops support in drm driver instead
of direct sde_power_resource_enable/disable call.
It allows drm driver to use runtime pm refcount logic
to track the resources instead of custom implementation.
The change also removes the NRT_CLIENT support from
sde_power_handle code to simplify it further.
Change-Id: Ib14692dca5876703d0a230da2512d731b69b8ebb
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
