Defines API and callbacks of os interface for P2P component. At the
same time, defines API of target interface.
Change-Id: Ice1c86ecba1f2410d965d9f84923589f229a1864
CRs-Fixed: 2013763
Include cac duration and regulatory domain in vdev start
command, these fields are used to process phyerrors when
dfs is offloaded to firmware.
Change-Id: I5736354913fafb7776ac71e85dc23e841de94a96
CRs-Fixed: 2017481
Add support to pass delay_start_time to firmware, this delay will be
used before starting the first scan cycle.
Change-Id: I7488fc8da4e22b170e52fb38c8a1d5b49dbf7e2f
CRs-Fixed: 2014142
Remove WMI VDEV param population for HE ofdma_cplen
command. Instead use the same old short_gi command
for HE ofdma cplen.
Change-Id: Id303dab1c7ec47ebc31fc685ad0b50ddfdf4fcac
CRs-Fixed: 2009118
Curretly FW considers minimum time of hysteresis for PER based roam as
constant value which is 25 seconds.
Add changes to make this time configurable using ini.
Change-Id: Iadb5f6a005b069e0d6190df34e382927425ec1af
CRs-Fixed: 2005849
DUT should be able to roam to a better access point if current
AP is having congestion/packet error.
This roam also devise a new selection logic for candidate
selection which considers channel congestion and AP capabilities.
Change-Id: I6cffbf0de059a218e971be32fbdc1a0092ceea9d
CRs-Fixed: 1090934
Active Mode Berkeley Packet Filter (Active BPF) is a new feature that
allows firmware to apply BPF even while the Apps processor is active.
There are 3 modes:
* Disabled: do not apply BPF in active mode
* Enabled: apply BPF to all packets in active mode
* Adaptive: apply BPF up to some threshold to avoid performance impact
Add WMI APIs and related logic to support configuration of Active BPF
Mode.
Change-Id: I8c0778b3fa73d148422aa103b0fc0950433fec95
CRs-Fixed: 1111400
Converged FW has few left-over WIN specfic WMI CMDs that need to be
implemented in TLV method.
WMI CMDs implemented through this change -
WMI_GPIO_CONFIG_CMDID
WMI_GPIO_OUTPUT_CMDID
WMI_PDEV_DFS_DISABLE_CMDID
WMI_PDEV_DFS_ENABLE_CMDID
WMI_PDEV_GET_NFCAL_POWER_CMDID
WMI_PDEV_SET_HT_CAP_IE_CMDID
WMI_PDEV_SET_VHT_CAP_IE_CMDID
Change-Id: Iad5532b305fae12f4eb8265cf9a662578041d06e
CRs-Fixed: 1115239
Converged FW has few left-over WIN specfic WMI CMDs that need to be
implemented in TLV method.
WMI CMDs implemented through this change -
WMI_PDEV_SET_ANTENNA_SWITCH_TABLE_CMDID
WMI_PEER_SMART_ANT_SET_TRAIN_INFO_CMDID
WMI_PEER_SMART_ANT_SET_NODE_CONFIG_OPS_CMDID
WMI_PEER_ATF_REQUEST_CMDID
WMI_FWTEST_CMDID
WMI_QBOOST_CFG_CMDID
Change-Id: Ice617f7adf387d534edaefd24857c253c937de48
CRs-Fixed: 1115239
Converged FW has few left-over WIN specfic WMI CMDs that need to be
implemented in TLV method.
WMI CMDs implemented through this change -
WMI_PDEV_SMART_ANT_ENABLE_CMDID
WMI_PDEV_SMART_ANT_SET_RX_ANTENNA_CMDID
WMI_PDEV_SET_CTL_TABLE_CMDID
WMI_PDEV_SET_MIMOGAIN_TABLE_CMDID
WMI_PDEV_GET_TPC_CMDID
WMI_VDEV_RATEMASK_CMDID
WMI_VDEV_SET_DSCP_TID_MAP_CMDID
WMI_VDEV_FILTER_NEIGHBOR_RX_PACKETS_CMDID
WMI_PEER_UPDATE_WDS_ENTRY_CMDID
WMI_PEER_SMART_ANT_SET_TX_ANTENNA_CMDID
Change-Id: I6e59bcb948a7368729df35d19c3d5a03a0075a15
CRs-Fixed: 1115239
Object manager psoc service ready api provides host (ext)service ready
data structures hence remove duplicate copy from wmi_unified_param.h
and change WMI to use psoc service ready data structures.
Change-Id: Iaec20e9b818077ed1ca58754c4b1bc6deaedd761
CRs-Fixed: 2002016
Currently, Host maintain multiple data structure at different
layers for offload related features like arp/ns/gtk etc.
Instead of using many structure use single data structure across
all layers for offload related feature (arp/ns/gtk) which is now
exposed by PMO. Hence to include PMO header's in WMI, refactor the
WMI code for PMO component by carving out PMO specific functionality
separatley.
Change-Id: I8314d5ece49bf6972fbe706d635385ae22d11b2e
CRs-Fixed: 2004523
Added host WMI VDEV param enumerations for new HE
commands Populated VDEV param TLV with WMI VDEV
commands ids for all the new HE commands.
Change-Id: Id9905176c7565dfa0dd56800b61b7c620136a4e7
CRs-Fixed: 2009118
Add HE Mac, PHY , MCS , OP & PPET in peer_assoc_params
structure. Add HE PHY & PPET in wmi_host_mac_phy_caps
structure. Populate HE params while sending WMI Peer
assoc commands.Parse HE Phy & PPET while parsing Mac
Phy TLV in Service ready extension event.Add required
changes in psoc_service_ready header files.
Change-Id: Ia2fc7f54634a7a0c98996e361e38b11b3b74a7a0
CRs-Fixed: 2009118
Add multiple vdev restart command request WMI command API and
extraction API for CSA count status event to support CSA implementation
for beacon offload.
Change-Id: Ic309f592137dc725e04590dc0093f30b481ebf9b
CRs-Fixed: 2000449
Added support for wmi_pdev_param_mesh_mcast_enable and
WMI_SERVICE_ENTERPRISE_MESH
Change-Id: Ie0ce2b822843d66aa14fe0a46809a78e9143f5d9
CRs-Fixed: 2003389
wmi_host_mgmt_rx_hdr struct cleanup for UMAC covergence as
struct mgmt_rx_event_params is to be used in place of
wmi_host_mgmt_rx_hdr.
Change-Id: I7ad3b641e492ecb469fa69c0025c6537c8a01e65
CRs-Fixed: 1103247
Send beacon frame in wmi_roam_invoke_cmd to firmware
This helps firmware skip scan to connect to requested
BSSID.
Change-Id: I5c6e375309dcb3bdd6430a3d501bade5cfe2e88d
CRs-Fixed: 1116901
Support to add hw_mode in init command is added by FW
to let host choose the mode to be use. Change init cmd
send API to enable upper layer to send the hw_mode selected.
Since this is new TLV in init command, init cmd send API
needs to be changed to accommodate this parameter.
Change-Id: I172d8d737425599c36666d9fec8a6cdd48085097
CRs-Fixed: 2004652
pdev_id is required to identify the pdev object on which this event is
recieved. Add pdev_id in the event extract API.
Change-Id: Ia910d42af6a9d6099da1b7781601b0320dff80ba
CRs-Fixed: 2003898
pdev_id is used to get the pdev for which the event is recieved. Add this
in extract APIs to fetch the pdev from pdev_ids and use it for further
processing. This is change is part of changes required to support
multi-radio.
Change-Id: Iadda098ccb31be5e8e43083158802abe49ac01b4
CRs-Fixed: 2003898
This patch adds support of new WMI command WMI_COEX_VERSION_CFG_CMID
for 4-wire coex configuration in non_tlv_ops.
Change-Id: I63da2c7ae99c38d297f7f13a8086611263f7fc5b
Acked-by: Daniel Kim <kimdan@codeaurora.org>
CRs-Fixed: 1081065
Add host internal definitions for the enumerations
WLAN_BAND_CAPABILITY and wmi_channel_width defined in wmi_unified.h.
This is required in order to allow common host code to access these
definitions agnostic of the actual version of wmi_unified.h used.
Testing:
Compiled and tested association and ping on QCA8074 and QCA9984.
Change-Id: I966211deb29ff3d65817b36ac4c6aefdbd39221c
CRs-Fixed: 2005796
Hold additional reference to BSS node during node allocation, and free
it in delete response. This ensures BSS Node Freed event is sent to MLME
only after receving peer delete response for BSS node.
Change-Id: I384eac54f437000a1c09eb53751ad8b8e26617ad
CRs-Fixed: 1112381
Add WMI_HOST_WLAN_PHY_MODE enum values for 802.11ax. These values
correspond to the WLAN_PHY_MODE enum values defined in the host-FW
interface.
Note that the new values for WMI_HOST_MODE_UNKNOWN and
WMI_HOST_MODE_MAX will not necessarily correspond to the MODE_UNKNOWN*
and MODE_MAX*/PHY_MODE_MAX* values in FW header files for all
chipsets/architecture families. This is because:
1) The 'unknown' PHY mode should not be used in host-FW interactions.
2) WMI_HOST_MODE_MAX is not currently used for host-FW interactions.
3) MODE_MAX*/PHY_MODE_MAX* values in FW header files can have varying
values at compile time depending on compile flags such as
SUPPORT_11AX, which in turn depend on the chipset/architecture
family. However the WMI_HOST_WLAN_PHY_MODE enum is exposed to
chipset/arch independent higher layers within host which utilize WMI
layer services. Hence WMI_HOST_WLAN_PHY_MODE enum values should not
vary.
In case the max mode value needs to be used in host-FW interaction in
the future for some reason, this should be translated separately by
the arch dependent (and if ever required, chipset dependent) WMI layer
code into the enum value directly exposed by the relevant FW header
file version for that arch/chipset. Similarly, if the arch/chipset
dependent max mode value needs to be used in-within host code in the
future for some reason, a separate variable should be dynamically
populated by the WMI layer at attach time.
Later, it might also be preferable to convert even other
WMI_HOST_WLAN_PHY_MODE enum values into values directly exposed by FW
header files in the manner noted above.
Testing:
Tested basic AP bring-up on M2M Platform with 11ACVHT80 and 11AHE20
Change-Id: I64c7a1d7491d2213c740568c3e9e2f035c82746e
CRs-Fixed: 1106923
This is needed for a requirement to change A-MPDU configuration
from per radio to per vap.
Change-Id: I916985d49bc5b059b7887b945acde798be0b38e3
CRs-fixed: 1107866
Add pdev_id in FIPS extract params to be used to get appropriate pdev.
Also refactor extart APIs to get all data in one API and implement TLV
APIs.
Change-Id: Ib58d54ad0dcc25814e58f45e7e4a83d01549a523
CRs-Fixed: 1115213
Add TLV APIs to extract DCS intereference event. Add pdev id in
extract API used to derive pdev object.
Change-Id: Ie42ec1e3aec899ddc5b6b13d37dfd468ee29df7c
CRs-Fixed: 1115213
Add extract API for handling UTF event data received from the target
for both TLV and non-TLV cases.
Change-Id: I62525d7c8663fe90e0e3e76cf5286bb9dc86acd0
CRs-Fixed: 1115293
Add hw_mode_id. HW mode is received in extended service ready.
This will be used to determine FW capability to support multiple radio.
This is used on host to create multiple instantces of pdev on host.
Change mac_phy_cap extract API to get mac_phy_cap based on hw_mode_id
and phy_id
Change-Id: I9a6abdac8799d167828f13bef61b1a1d8c3e9769
CRs-Fixed: 1113888
Defination of enum WMI_DBG_PARAM is used only in host
so moved to host private wmi file.
Change-Id: I42a529b343e4e6e81b570c505385cfc8dbf9f017
CRs-Fixed: 1107600
Convert the wireless_modes HALPHY capability from FW defined REGDMN_MODE
values to host internal WMI_HOST_REGDMN_MODE values. This will help make
host code independent of target specific definitions.
Change-Id: I6d325f76959b35a3f854ade680f4d058c9d4bfcb
CRs-Fixed: 1061096
When CTL array is configured using acfg_tool, the CTL values are not
impacting powers due to incorrect band value passed to the FW. It is
found that the memory copy for band and CTL array are done together
in a single operation.
However, with convergence, both acfg_tool and wifitool will call the same
underlying WMI API to set the CTL table. In order for concurrent working,
we need to copy the band value separately for acfg_tool, before copying
the CTL array. This fixes memory corruption that is currently seen
as evident from the garbage value for CTL band.
CRs-Fixed: 1087168
Change-Id: I42f6bc39eb3930e8c995ff76294b7d77676f2299
Propagation from qcacld-2.0 to qcacmn.
Several Action frame categories are not processed in host and they
are not forwarded to supplicant either, but they are dropped in host.
These unprocessed action frames are forwarded to host by FW and
wake up host unnecessarily which leads to battery drain. With this fix,
host conveys FW the disallowed action frames list at HDD startup
so that the remaining frames can be dropped in FW itself thereafter
when under WoW mode.
Change-Id: I40b49d42df94085784c8f1d8321de0ee61473ae0
CRs-Fixed: 999114
Add WMI host defines to check cal data status and use appropriate copy
macros to take care of big-endian conversion.
Change-Id: I4358761e807ac584c638b6e36229dbbbb85bf651
CRs-Fixed: 1105756
There is a regulatory requirement for Specific Absorption
Rate (SAR) whereby the phone transmit power is reduced
when it is determined that the phone is in close
proximity to the body.
Implement a vendor command interface to set SAR power
limts dynamically.
Change-Id: I0a214a2af780e9dd8c381c4e9eaa7d8cab6ef853
CRs-Fixed: 1098102
The term "agile" is used by hardware for swift/fast channel change.
Use precac for the zeroCACDFS instead.
Change-Id: I35f4d61cc93b3542feb8b286cbdf3a4474df5a75
Crs-fixed: 1073945
A new iwpriv command has been added to configure the period
and wlan duration for a btcoex duty cycle.
As a part of this registring the wmi_service_btcoex_duty_cycle
for WMI_SERVICE_BTCOEX_DUTY_CYCLE.
Also send_btcoex_wlan_priority_cmd registrtaion for btcoex
duty cycle command in non_tlv_ops.
Change-Id: I7f3bfdfd9804566d6d0b7cce7025e99db57d0e23
Acked-by: Basamma Yakkanahalli <ybasamma@qti.qualcomm.com>
CRs-Fixed: 1064437
Agile flag WMI_CHAN_FLAG_AGILE_MODE added. When this flag is set,
the primary VHT80 will not be affected when channel change is done.
Change-Id: Ie6bce12ec955c0c8a79246dda57092808611803d
CRs-Fixed: 1072504
For WOW Enable, firmware accepts a bitmap of flags, but passing them
to firmware is not exposed by WMI. Modify WMI to allow passing WOW
Enable flags to firmware.
Change-Id: I458b01bc6a4e5b14b2a1dfee928136daeb70ebe9
CRs-Fixed: 1092068
Add helper routines to extract TLV params in WMI EXT service ready
event. These helper routines abstracts all TLV related information
providing APIs to extract ext serivce ready params.
Change-Id: Ic989331856ed2f9376965bdec4b658328f9e470b
CRs-Fixed: 1079237
For Beeliner family of chipsets, the number of values expected is 688
for 2G and 1540 for 5G
Change-Id: I2c47ed98f639c09453687fce7f713946304a7036
CRs-fixed: 1071083
Recently added changes for coexistence of WIN/MCL TLV implementation
through CL I6868c288a43fd3afb19c84b8a9d4ef0dfbee5c94 require
adaptations in QCA WIN driver to successfully compile.
Add required definitions in WMI layer to adapt WIN driver to
changes made for coexistence.
Change-Id: I99550ca10553d8096b8967249c006bac4e0c62df
