Pdev parameter to prioritize IGMP packets are supported through
WMI_PDEV_PARAM_IGMPMLD_AC_OVERRIDE. In legacy platforms, they are
supported by different pdev parameters WMI_PDEV_PARAM_IGMPMLD_OVERRIDE
and WMI_PDEV_PARAM_IGMPMLD_TID.
Map host maintained pdev params wmi_pdev_param_igmpmld_override and
wmi_pdev_param_igmpmld_tid to WMI_PDEV_PARAM_IGMPMLD_AC_OVERRIDE since
this is the one supported by TLV based targets.
Change-Id: Ia11787265bd926f257dc1b028552c6e7f1f733d2
CRs-Fixed: 2272219
In implementation of Android Packet Filter, functions, variables,
definitions are named after BPF, which stands for Berkely Packet
Filter. The term was more appropriate for Link Layer packet
filters implemented in the Linux kernel, known as Linux Socket
Filters.
The term BPF is obsolete now, so rename it with the
appropriate acronym, APF.
Change-Id: I606afc747cddedb524a41cd8e5998400f04e69f6
CRs-Fixed: 2191531
Send average radar parameters to FW.
Extract host dfs spoof check status from FW.
Change-Id: I70c4e5aad0fe1eda55da37abd20cc6d70728edba
CRs-Fixed: 2211883
Address the following issues in the wmi folder:
CHECK: 'addres' may be misspelled - perhaps 'address'?
CHECK: 'COMAND' may be misspelled - perhaps 'COMMAND'?
CHECK: 'defintion' may be misspelled - perhaps 'definition'?
CHECK: 'happend' may be misspelled - perhaps 'happened'?
CHECK: 'managment' may be misspelled - perhaps 'management'?
CHECK: 'messsage' may be misspelled - perhaps 'message'?
CHECK: 'overriden' may be misspelled - perhaps 'overridden'?
CHECK: 'poiter' may be misspelled - perhaps 'pointer'?
CHECK: 'refering' may be misspelled - perhaps 'referring'?
CHECK: 'refrence' may be misspelled - perhaps 'reference'?
CHECK: 'shrinked' may be misspelled - perhaps 'shrunk'?
CHECK: 'succesfully' may be misspelled - perhaps 'successfully'?
CHECK: 'succesful' may be misspelled - perhaps 'successful'?
Change-Id: Ie97e4d83cc88a2610524b38adc3474cdd31170d9
CRs-Fixed: 2241590
There are instances of use of older A_UINT/A_INT.
Replace all such instances with the qdf u_int*_t/int*_t.
Change-Id: I7ce29b03f29a0d1a0cf87cfd3c846f4694da4c2a
CR's-Fixed: 2210869
Add function for extract_nfcal_power_ev_param and
register wmi_pdev_nfcal_power_all_channels_event_id event
to support noise floor in HK.
Change-Id: I6eef823b507be94c65df026664244eec7fc07e24
CRs-Fixed: 2157972
Current Spectral module uses qdf_print. To improve the control over
logging, use module level logging
CRs-Fixed: 2165341
Change-Id: I205991347453c4dcc424ba1958e309b7c5fb71a0
Change WMI initialization sequence to support WMI modularization.
TLV and Non-TLV modules calls WMI module registration based on target type.
WMI attach will call respective attach routines based on registration.
Change-Id: Id56446f491d129758537913d2d5d6633f8dec918
CRs-Fixed: 2179854
command:-
1. "iwpriv athx s_txpow param1 param2"
2. "iwpriv athx g_txpow param1"
param1 = frame_type<<8+frame_subtype param2 is power_value
if subtype == 0xff means set all subtype of that frame type
Change-Id: I8c68e1ca6a5829a3f0cf01b2c32c3332e1010243
CRs-Fixed: 2175241
Added a WMI command to add and del peer from the list
of non associated clients for which the RSSI stats
need to be populated
Also added event handler to extract the rssi stats
from the WMI event
Change-Id: I9880c74798c13a52e1498b81735ad78f86fa41b8
CRs-Fixed: 2148773
Add new WMI EVENT, SW FILS Discovery Alert Event, to get
firmware trigger to transmit FILS Discovery Frames.
Add WMI command to send FD frame buffer to firwmare.
Add WMI command to set FD period interval in mili seconds.
Change-Id: I8cb6279ec4431b9236bd32c548228a0dc6598664
CRs-Fixed: 2118098
fwhdr_abstrct: Use Host based TARGET_TYPE instead of firmware
defined TARGET_TYPE. It will abstract dependency on bmi_msg.h.
Change-Id: I76d744db27df730a3a91a243adfc07fc17d77487
CRs-Fixed: 2140921
For big endian based offload radios, the key installed using
WMI_VDEV_INSTALL_KEY_CMDID requires to be code swapped as the
copy engine for big endian platform does byte swap operation
on the received key before sending it down to FW.
The big endian conversion is carried out
in ol_if_vap.c for big endian platform specific radios.
However, it is observed that an additional copy
is carried out in the WMI layer that is overwriting
the converted key with old key, in the non-swapped form.
Hence move the big endian operation to the WMI layer to
ensure uniform functioning of the API
Change-Id: I9ee16572d08045b0f55b0de190efba5c6806031c
CRs-Fixed: 2161682
Direct Buffer Receive provides the driver with a mechanism by which target
can transfer information directly into host memory via DMA.
Add support for the following service/events/commands -
1. WMI_SERVICE_SUPPORT_DMA
2. WMI_DMA_CAPABILITIES as part of WMI_SERVICE_READY_EXT_EVENTID
3. WMI_PDEV_DMA_RING_CFG_REQ_CMDID
4. WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID
5. WMI_DMA_BUF_RELEASE_ENTRY
Change-Id: I3949026b4542565c49bb538b9545ea607690c793
CRs-Fixed: 2158304
Add status recieved as part if WMI ready event into wmi_ready host param
structure to enable the removal of seperate API to extract status. Add
new param introduced by FW to indicate number of extra peers FW is
allocated for its internal use.
Change-Id: I7a9ed64d4a9d1f38397197c4c4a4114d8365eef7
CRs-Fixed: 2149878
Request and print WDS table from FW using WMI command and event.
WMI_PDEV_WDS_ENTRY_LIST_CMDID is used to request WDS table
entries and WMI_PDEV_WDS_ENTRY_LIST_EVENTID is used to process
received WDS entries.
Change-Id: I452c8067d191d09826a38b751bb66f1bde587d9b
CRs-Fixed: 2003377
WMI ready event provides num_dscp_tid, num_total_peers and other
information that is used. Add API to extract these params.
Change-Id: I85ffc43f20935d84de133591020468c5e5f102de
CRs-Fixed: 2141667
Add new pdev param with which firmware can be set to use
a lower number of chains without doing a reset. In response
to this firmware's ratecontrol will select only rates
which can be sent using a lower number of chains, and set
the h/w tx descpriptor's chain select to whatever value
has been configured using this command.
CRs-Fixed: 2123206
Change-Id: Ice713393958c2c2acedba0fe2e9354f3fe3bee75
Add WMI vdev param to indicate firmware not to buffer mcast frames
even when clients are in power-save.
CRs-Fixed: 2133095
Change-Id: I4fe936e6a490ec8007f909e1ba079bec2f2713cd
FW reports build number in service ready and ext_service ready event.
Save these to display FW build version during brinup.
Change-Id: Ia86a392f826c5bb836be9353e3938ab1f811ab62
CRs-Fixed: 2125667
Add functions to send bridge MAC programmed from user
space to firmware.This change is part of a workaround
to fix an looping issue which resulted in wrongly adding
bridge's own MAC address to fw WDS table.Send MAC address
to target to avoid adding our own bridge address to fw
WDS table as part of source port learning.
Change-Id: I815d3c3f106cd2f528ac9172712ec6c2f47f4410
CRs-Fixed: 2070956
Extended service bitmap is used by FW to indicate supported services
bitmap for services excedding the current limitation of 128. Add support
to save and use this bitmap to check services supported in FW. Also,
change exisiting services bitmap to be dynamic allocated buffer to
optimize the buffer used to save the bitmap.
Change-Id: I24a0321bc1a06ee3aedf1c6acbc379e907bbd464
CRs-Fixed: 2103617
Add support to fetch min and max tx power from target for
a given set of mcs, nss, chainmask, bw, and other rate flags.
Change-Id: Iafe082db81503a52bdc704d4b71d86d23788fddb
CRs-Fixed: 2061802
Add required WMI commands to communicate support of
EXT NSS Signaling between host and FW. Also, if
EXT NSS Signaling is supported the use new WMI to
communicate the required information between host and FW.
Change-Id: If3e1ef11a55f8fbdffddb3b10963878a6a2ca415
CRs-Fixed: 2089043
Remove redundant header file inclusion from wmi layer by abstracting
the dependency with in WMI layer.
Change-Id: Ie113b69006a960b70d781134775bc44c7508fc4c
CRs-Fixed: 2023825
HT cap bit map is different for tlv and non-tlv based firmware.
Convert target cap to host cap bitmap to abstract out the differences.
Change-Id: Ia803efa3a895c7faa159d8051277d2a926b365a5
Remove unwanted prints from the dirver and also change tha log levels
from some of the prints which could be useful in debug pruposes only.
Change-Id: I2b4e0c94fcf1571b332fc005b34bc4b7bcb4b7c5
The tx_iv flag of wapi has been changed
from an array of type u32 to array of type u8
this change adds support for it .
Change-Id: Ia0e57e25c151e7f7f232cf8dc07d59d5a19b47e0
Added support for wmi_service_chan_load_info which is newly
added in wmi service bitmap.
Change-Id: I95905ac95c5305f8f84ec512ecf1859955704193
CRs-Fixed: 2057719
Recently, FW changes were implemented to support WMI resource config for
multi-radio. As part of this, the TBTT offset and SWBA events were modified
to support increase in the number of vdevs per SOC.
Brief description of the changes with respect to TBTT offset
------------------------------------------------------------
Converged FW will send extended TBTT offset event when the number of vdevs
configured is greater than 32 and will continue to send normal TBTT offset
event when the number of vdevs configured is less than 32. Legacy FW will
continue to send vdev map and tbttoffset list array as part of the TBTT
event.
Extraction API is added to extract the number of vdevs configured for both
legacy and converged FW. Number of vdevs is sent directly by the FW for
extended TBTT offset event but sent as vdev map for the normal TBTT offset
event. In order to handle normal TBTT offset event, extraction API for
normal TBTT event adds logic to convert vdev map into the number of vdevs
configured.
Extraction APIs are added to extract vdev id and tbttoffset information per
vdev that are configured. The vdev id information is sent as vdev map and
tbttoffset list as an array for normal TBTT event and as an array of
structures containing vdev id and tbttoffset in the case of extended TBTT
event. In order to support normal TBTT event based on num vdevs, extraction
API for normal TBTT eventadds logic to determine the vdev id from vdev map
based on the index(running through 1 to total number of vdevs) passed from
the driver.
Brief description of the changes with respect to SWBA
-----------------------------------------------------
Converged FW will send additional information num vdevs and vdev id
embedded in tim info and p2p noa TLVs for SWBA event. Legacy FW will
continue to send vdev map and array of tim info and p2p noa desciptors.
Extraction APIs is added to extract the number of vdevs configured for both
legacy and converged FW. Number of vdevs is sent directly by the FW for
SWBA event in the case of converged FW and as a vdev map in the legacy FW.
In order to handle legacy FW, extraction API for non-TLV adds logic
to convert vdev map into number of vdevs configured.
Extraction APIs are modified to extract newly embedded vdev id information
in tim info and p2p noa descriptors. The vdev id information is sent as
vdev map for legacy. In order to handle legacy FW, extraction API for
non-TLV adds logic to determing the vdev id from vdev map based on the
index (running through 1 to total number of vdevs) passed from the driver.
Change-Id: Ibf84adbb1c526321ec031d5539aff66dcbd1315b
CRs-Fixed: 2053628
Changes added to support multiradio feature.
Included pdev_id and/or vdev_id in required ATF specific WMI data
structures. All ATF commands will be sent with pdev_id and/or vdev_id.
Change-Id: I723a9a6e4a67a417d4aa2b392285dc4afa590a21
CRs-Fixed: 2052786
pdev_id in FW starts from one. Zero is reserved for Soc. But host uses
pdev_id starting from zero. Make WMI changes to take care of this
difference and always provide and accept pdev_id starting from zero at
WMI. Use 0xFF for SoC on host.
Change-Id: I49f481e54bbaeea9359753bc7d3da9092fc9559a
CRs-Fixed: 2045125
