During one of the DP timeout usecases, flush doesn't take
effect due to vid vblank wait failure. As a result, smmu
faults are observed because of fetching the previously
staged planes. This change adds ctl reset in the same
DP atomic commit context to recover and avoid
smmu faults.
Change-Id: I2f9aceca56e27f140607317f7596d6fe0d908af8
Signed-off-by: Yashwanth <yvulapu@codeaurora.org>
This change adds pending ctl recovery mask in sde kms
structure to check if there are any ctl paths pending
for recovery and stages only border fill during such
conditions to avoid device crash. Below is the issue
sequence observed during the crash:
1) On one of the ctl path, flush didn't take effect and
flush bits are still pending.
2) It was a NULL flush and last good flush on that
interface has DMA2 pipe staged along with other pipes.
3) Different ctl path re-uses the DMA2 pipe (attached to
ctl path in #1) causing wr_ptr timeout followed by
ppdone timeout.
Change-Id: I07eb9f2fe41f59963dc27655c551c05abe240392
Signed-off-by: Yashwanth <yvulapu@codeaurora.org>
Trigger various panel event notifications when
operational fps and power mode changes.
Change-Id: I8c5e066c8f20de4c31bb21a6fd6226dd93678fb6
Signed-off-by: Shashank Babu Chinta Venkata <sbchin@codeaurora.org>
Add a new connector range property and a new entry to the panel
capability blob to publish the list of supported RFI frequencies.
In addition, add the required functions to set, validate and update
DSI bit clock rate value to trigger an internal seamless mode switch
and reconfigure DSI clock and PLL.
Change-Id: I7d19cc369f8c5528709f2f20a51ef02180ebdea4
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
For GKI2.0, the old drm_panel_notifier function could not
be used anymore, so removed it.
Change-Id: I858f90d7c39816dc95ab59f88c8988237319eadc
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
Trusted-vm uses the cont-splash path to initialize the software
states by reading the hardware registers and populating the
SDE & DRM software states. But drm mode cannot be determined by
register reads, so rely on user-mode to get the mode which comes
as part of the first atomic_commit check phase which handles the
transition. The primary-vm user-mode passes the current mode to
trusted-vm through qrtr which is in-turn passed to driver to
set that particular mode.
Change-Id: I4fb86b40b8a0583c8edb539b0a51dcd33de731ff
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
The MEM & IRQ lend handlers signals the resources
are lent from the primary VM. Reserve the SDE HW
resources in trusted VM using the cont-splash path
and setup the SDE & DRM software states. Set the
DSI connector status to active for the handoff
display during the start and disable it at the end
of the session.
Change-Id: I75b6df735eb5609cc521808aca0ddfb0b3993e84
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Extends atomic check to validate TUI transition request aginst
SDE and non-SDE client states. Triggers HW assignment after
making sure current frame is completely flushed out of HW
pipeline. Initiate the acquire after TUI end after restoring
the software states.
Change-Id: I6ceccd44c18526ff818723b5631b66af3ff083c1
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Add VM layer files to handle VM specific operations
for primary and secondary VM's. They interact with
Hypervisor RM modules to LEND/ACCEPT/RELEASE/RECLAIM
HW resources. They also handle notifications for each
of the above Hyp RM operations to acquire and update
the SDE software states.
Change-Id: I5982f4bf56550dc464797c62cb356be39925b21c
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Commit d46cae019e ("disp: msm: sde: trigger pm_qos vote
with irq enable") moves the pm_qos vote with irq
enable/disable state. Such irq enable/disable call may be
triggered from atomic context and lead to scheduling issues
due to mutex_lock usage in pm_qos APIs. This change moves
the vote with encoder idle pc to allow lock usage with sleep.
Change-Id: I2d22566fbfb5399c5d2d2a4efe882a1928cfbbf8
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Add support to read register ranges and IRQ lines that needs
isolation during VM switch. Register for vm resource collection
event providing the callback function.
Change-Id: Ie1edf0794a8de89cc44279892433b45a54eba609
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Vblank refcount can reach out of sync with below case
1. event_thread triggers the vblank_enable
2. commit_thread triggers the modeset
2.a modeset resets the vblank refcount with mode_set
3. event_thread triggers the vblank_disable
Event 2.a resets the vblank refcount and vblank disable
request after 2.a is going to fail. This can be fixed
by avoiding concurrency between mode_set call and vblank
request.
Change-Id: Ibb810ec90e81d63feee443f1c37dd736d5cfac0d
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Add debug capability to dump clocks before entering pm suspend.
This will help debug invalid register access when clocks are off
during adversarial test cases.
Change-Id: I80d19b751a3b9a1de0cc64699a21a1852d614ced
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
Adds a DT property to indicate trusted VM execution
environment and support catalog parsing for the same.
Add helper API to read the value.
Change-Id: I9194618b6f080119f1f15271a9b3c7edf938ca08
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Treating hw version as a signed int results in a negative
number when major version is more than 7, leading to errors
when comparing versions in the driver. Fix this by making
sure all HW version definitions and variables are unsigned.
Change-Id: Ic77183f85e5408092e05817cf95df5b0f0fcac75
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Video mode display keeps the MDP clocks in ON state but
disables irq during static screen to avoid cpu wakeup.
In such case, CPU pm_qos vote should also be removed
to allow LPM transition. This change triggers the
pm_qos vote based on mdp interrupt enable counts
instead of runtime_pm callback. It works for
multi-display concurrency also.
Change-Id: I7a60f3f593e409269e00abd7499c4a5756035615
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Get the MDSS HW version from the device tree instead
of reading directly from the hardware register.
Change-Id: Icfb7a80c8f19312001b070a454741421fd67aae5
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Add a QoS vote on CPU receiving display interrupt. QoS vote
will prevent that CPU from going into low power mode avoiding
possible interrupt latency. Using irq notifier, display will
receive notification when display IRQ has switched CPUs and
will adjust the vote accordingly. The vote is also removed and
requested whenever display IRQ is enabled or disabled.
Change-Id: I94b4501896b4b20b37deaca90d6b5ff883d56621
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
In Dual display concurrencies there are certain cases where
irq_idx and vblank_refcount state mismatch can occur.
To avoid it, during setup of irq_hw_idx, reset the vblank_refcount
and unregister read ptr irq if not yet done by then along with
maintaining global mutex lock for vblank_refcount.
Also, if register IRQ fails, correct vblank_refcount so
that IRQ registration can be tried again.
Change-Id: I06bcbf71c6a43bd161ff61093d9f6063a292d6bc
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
This change moves the DSC implementation into a separate file.
This is required to add support for new compression algorithms.
This cleanup change also, moves struct sde_encoder_virt
declaration to the encoder header file.
Change-Id: Idc3b96e65fcce2a7ee6e17af604cec0cb574f6f7
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
During secure-ui, the SMMU, MISR and VBIF states
are altered based on the enable/disable of secure-ui
which is followed by the scm_call. Failure in any of
the steps would lead the system to an unstable state.
Address all the failures and revert back all steps
to get the system back in original state to avoid
any issues.
Change-Id: I736c6cf018c5992ec33806c00e58bf56b818b8a7
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Reverting the change to check for LTM SW fuse to install LTM properties
during probe since LTM SW fuse is enabled later.
This reverts commit 652b195ba4.
Change-Id: I19b3e04ff7caaad5de896fbcf433c3b1863ac4f9
Signed-off-by: Ramkumar Radhakrishnan <ramkumar@codeaurora.org>
This change saves the previous state before moving into the transitional
smmu state, during secure-display/secure-camera usecases. Upon failure
to complete the transition, set smmu state to the previous state.
Previously, smmu state was staying in transitional state.
Change-Id: I1a78ddcf6ac1c7ea66c8c2095cd1a6d6160647a1
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Add checks for LTM sw fuse value to only install the LTM properties
when the LTM sw fuse is set to enable.
Change-Id: I6876bfcf12ddb912e7b7a80e07c33108fd4b85b9
Signed-off-by: Ping Li <pingli@codeaurora.org>
This change ports the missing changes from 4.14 to 4.19
that were missed. It includes changes up until
commit 0f8fb25421ff ("cnss2: Add device version to
SOC info structure").
Change-Id: Idfdfe891f146e389e3c65cc3fc4c98d93220e789
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Add runtime_pm ops support in drm driver instead
of direct sde_power_resource_enable/disable call.
It allows drm driver to use runtime pm refcount logic
to track the resources instead of custom implementation.
The change also removes the NRT_CLIENT support from
sde_power_handle code to simplify it further.
Change-Id: Ib14692dca5876703d0a230da2512d731b69b8ebb
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
