Enable wcd939x surge reset routine. Add callback for
the event within mbhc and enable it for wcd939x.
Change-Id: Iabc8c3367ae2eca5982db4526c6860e5eba63b76
Signed-off-by: Eric Rosas <quic_erosas@quicinc.com>
add support for GND MIC SWAP config for pineapple CDP.
Change-Id: Ia6ecbe2818ac12c7fad5738a78bbdcd4d1611e15
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
While measuring the adc, if PA is on we will get incorrect values of
adc due to which the detection type is missmatched. So disable the PA
While measuring the adc values and restore back PA once measuring adc
done.
Change-Id: I5833452e23a71637353449bb48b937ee44be24ae
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Resolve warning log when hph pa mutex lock is destroyed before
unlock. Initialize hph pa locks as global lock and do not destroy
during SSR to resolve issue.
Change-Id: Idc5af793294f7fdc8dbcc17770f68fe2c46ab337
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
During SSR, when usbc analog device is disconnected, the
respective disconnect interrupt is not handled and hence userspace
is not notified. When ADSP recovers, fsa driver sends a disconnect
notification. So handle device disconnect and notify jack/userspace
through this notification.
Change-Id: Ic695c2267c9289f9528d50202938ec09f634de8a
Signed-off-by: Vignesh Kulothungan <vigneshk@codeaurora.org>
When current source mode is enabled, comparator auto
zeroing should be turned ON by HW. As rouleur codec HW
doesn't do this automatically, add this support
in SW to set the auto zero enable before FSM enable
and reset to auto once FSM is enabled.
Disable surge protection before ADC measurements
and change HPHL and HPHR thresholds while
identifying cross connection for proper
accessory identification.
Change-Id: Ib775de0f0bdb6c655a3c0eb4775276acfbca1e84
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
Current source mode in rouleur does not work
properly leading to issues in button interrupts
and fake electrical removal interrupts.
Enable pull up mode instead of current source
mode to fix these issues. Modify the headset
max vref voltage to 1.7 volts and micbias
calculation logic.
Change-Id: If3e4a2fdcf080b07fe3c363b6eb6115f101b91f4
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
ANC headphones are no longer supported, removed dead code related to the feature.
Change-Id: I3dd51b5b1d9f77fd870947608f8a14fc3f7aeed0
Signed-off-by: Akhil Karuturi <akarutur@codeaurora.org>
Add CONFIG_AUDIO_QGKI check for variables and functions
in audio drivers, so they are used only during a QGKI build.
Change-Id: Ia04232566367f196f298a49cf3962bb7927bec6a
Signed-off-by: Vignesh Kulothungan <vigneshk@codeaurora.org>
Audio is distorted during first 3 secs on headset record
while doing device switch from dmic to headset mic.
Disable BCS before slow insertion detection and enable it
afterwards to resolve the issue.
Change-Id: Ie5bc4b5292e5f69066760cab44d78989a74f13f4
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Max limit of 60k ohms was set for cable to be detected as lineout
to fix headset detected as lineout issue on legacy targets.
This was because of large impedance detected for headset.
This is not applicable for adc based targets as headset is
detected based on mic adc voltage. Remove max impedance limit for
lineout detection.
Change-Id: If73bbe2cd78d04d1fcb359a3e5ed5cd69f3ab9f0
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
When detecting special headset, vref for special headset is
set based on headset threshold reference 1800mv or based on
regular micbias settings from device tree. Scale threshold
reference as per the special headset micbias voltage.
Change-Id: Ic4cc24e18efeb420b53a2154707c9399eb886181
Signed-off-by: Meng Wang <mwang@codeaurora.org>
