During ESD check failure, DSI video engine can get stuck
sending data from display engine. In use cases where GDSC
toggle does not happen like DP MST connected or secure video
playback, display does not recover back after ESD failure.
This change adds support to perform soft reset when DSI
video engine gets stuck.
Change-Id: I9cb31e6c71c4da171f9fe22fc3bee9175711831d
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
As per DSI HPG, Soft reset is not required to disable
video mode operation for version 1.3.0 and later. So,
add check to skip it during display disable.
Change-Id: If6d263bdf22f8a6fbef76d78d04bb9d11be05945
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
The change adds register mapping of MDP_INTF_[1/2]_TEAR_INT_COUNT_VAL
register to DSI controller. This allows for the controller to read the
line count and frame count of the read pointer during trigger and
successful transfer of DMA command.
To enable the debug feature:
echo 1 > /d/<panel_name>/dsi-ctrl-0/enable_cmd_dma_stats.
To disable the debug feature
echo 0 > /d/<panel_name>/dsi-ctrl-0/enable_cmd_dma_stats.
To read line count value:
cat /d/<panel_name>/dsi-ctrl-0/cmd_dma_stats.
Change-Id: I5cdeb54ca941af05b226a9d7ab332b899ecc5797
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
The change allows for configuring a command DMA window during which
the command is triggered. The DMA window must not intersect with the
MDP tear check window. Once the command transfer is successful, the
trigger control needs to reset to the default DMA trigger specified
by the panel.
Change-Id: I5485ca1f8e141ed92dc8c77c2daf579634271022
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
From Lahaina onwards, for compressed DSI output, widebus should be enabled.
In widebus mode, 6 bytes of data are transmitted per pclk.
For uncompressed output, widebus must be disabled to transmit 3 bytes
of uncompressed data per pclk.
Change-Id: I7fc0bdb2e1678152d57b4cbb8295063a2ba8ae73
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Move DSI debugbus dumping logic from DSI driver to sde_dbg
in order to utilize the framework in place for debugbuses.
This allows for more control over the dumping logic, such
as where the dump data is stored(memory/console), via nodes
populated in debugfs.
Change-Id: Iff507fdaa02d26af26743e81f6048aec57c09a76
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
DSI PLL is tightly coupled with DSI PHY. This change removes
separate DSI pll driver and makes DSI pll as a subnode to DSI
PHY which is an accurate way of representation. In addition, this
change adds support for 5nm DSI ctrl and PHY revisions and adds
DSI pll support for 5nm. Remove support for older DSI pll revisions
such as 7nm, 10nm, 14nm, 20nm, 28nm.
Change-Id: Ic8b886a9fe24b906e4ec5130720600efa1e59b68
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Change lowers the log level of the debug bus dump to info.
Change-Id: I129f9f2e611428dc392d7888df43870beddac307
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Adding debug, info and error prefix for log messages
in dsi files. To enable debug logs
run "echo 0x1 > /sys/module/drm/parameters/debug"
Change-Id: I438ac16954bd1d39450f8adeb7fb17f9ea6f8140
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change is a snapshot of dsi files taken of 4.14
as of commit 764f7c2 (Merge remote-tracking branch
'quic/dev/msm-4.14-display' into msm-4.14)
Change-Id: I8361a844c35a4450f7800964a8da2741676fd6c7
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Continuous splash enabled displays are identified by reading
the MDP ctl registers. DSI cont-splash init settings are
called based on this. Additionally, DSI reads the DSI-CTL
scratch register set by bootloader to detect cont-splash.
This change removes the redundant mechanism in DSI to
detect cont-splash.
Change-Id: Ic58be1e62eda239fcea5e82d9d356905dc552a73
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change adds support for dynamic switching of dsi clocks
to avoid RF interference issues. Also with dynamic dsi clock
switch feature coming into picture, now populate the supported
refresh rate as list instead of providing a range. Modify the
logic to enumerate all the modes in dsi driver, taking dynamic
bit clocks, resolutions and refresh rates into account.
Change-Id: I5b6e62bc935cf2234bdd96fcb3c7537b4e735fff
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Yujun Zhang <yujunzhang@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
