Remove edid/dpcd simulation function from dp_debug and calls to
sim bridge instead to simplify dp_debug module. Also add mst edid
support and mst hpd simulation from aux level.
Move selected mode from dp_debug module to dp_panel module to
simplify mst handling and decouple dp_debug from main dp driver.
Remove custom edid/dpcd mode from dp_panel and dp_aux module.
Remove mst connector list handling from dp_display module.
Change-Id: Ife1d2deb0e353f0a9695b7b90e5bf3459e1c81f7
Signed-off-by: Xiaowen Wu <wxiaowen@codeaurora.org>
Signed-off-by: Karim Henain <khenain@codeaurora.org>
Signed-off-by: Sudarsan Ramesh <sudarame@codeaurora.org>
This change adds the support to request the dp link clk rate
through the mmrm driver. In the case the system can not
support the rate, user space is notified of the failure and
dp is diconnected.
Change-Id: I4a074054ce42425ca940d4aec505723724736b44
Signed-off-by: Christina Oliveira <coliveir@codeaurora.org>
Current implementation waits for 10ms prior to sending the connection
notification to user mode. This delay is to check for any potential
IRQ HPD event from the sink which may require a link maintenance.
However, this delay may not be sufficient for certain use cases.
Increase this delay to 150ms and modify the implementation to exit
the wait whenever an IRQ HPD is received. This ensures that we can
process the IRQ HPD in a timely manner as per the specification. To
further improve debug ability, add the support to configure this delay
though debugfs:
echo [delay_ms] > /sys/kernel/debug/drm_dp/connect_notification_delay_ms
Certain cables are unable to handle back-to-back HPD notifications and
may end up skipping some events. To improve interoperability, delay the
handling of disconnect notification. Sinks would typically issue an HPD
high following an HPD low only after they sense that the mainlink has
been torn down. Delaying the handling of HPD low would in turn delay the
issuing of the subsequent HPD high from the sink. Here again, make this
delay configurable through debugfs to improve debug ability of these
interop issues:
echo [delay_ms] > /sys/kernel/debug/drm_dp/disconnect_delay_ms
Change-Id: Ie29198af4dcda6d392798a3a93ebb3ddaa6746c8
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
The debugfs api for mst control is a multi stage process where the
connector id is selected using the mst_con_id node, which is then
used on other commands such as edid_modes_mst for mode switch.
During mode switch control, the mode is set using the current id
for a display and then the switch is initiated through an unplug
and replug. But on an unplug the connector is destroyed and a new
id is assinged for that display on the subsequent plug. This
change detects this scenario and updates the cached connector id
with the id from the newly created connector.
Change-Id: Ib51566ac9e334d4a0b145b6ae549c59c537cb0cd
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Modify the macros to use default kernel logging function if DRM log
levels are not explicitly set. This helps in being able to selectively
enable function or file level logs.
Change-Id: I4f894a2ecf314a3a5fc0bb22a75a0e10dae31e07
Signed-off-by: Aravind Venkateswaran <aravindh@codeaurora.org>
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
Use the new altmode framework to receive the connect, disconnect
and attention events.
Change-Id: Ic542525b526e1abd0f153c293bca6e4cdbb6bf0b
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
Add support for PLL programming in the DisplayPort driver.
Change-Id: I4f08a621dcae5d1f54d67bb5c34409249012cc7b
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
Adding prefixes for error, debug and info
messages in dp files. To enable debug logs
run "echo 0x100 > /sys/module/drm/parameters/debug"
CRs-Fixed: 2493739
Change-Id: Ibf509e837f527be6bff6b7a1c34b0cde2921b388
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Improve dp mst simulator mode by adding support
for up to 8 connectors, the ability to add and
remove ports dynamically, and allowing for
different EDIDs for each connector.
CRs-Fixed: 2459530
Change-Id: I945e3292a7e5150ab7a6bbe0addc4f4f46d58e82
Signed-off-by: Fuad Hossain <fhossain@codeaurora.org>
The DP standard leaves ambiguity to if sink synchronization
will be set before auxiliary protocols such as HDCP are to begin.
Update the dp_display HDCP worker to check sink sync only if
explicitly instructed to via the new debugfs node 'hdcp_wait_sink_sync'
Change-Id: I4f4d0b14096aa3dc498e47de557de14092d37a58
Signed-off-by: Christopher Braga <cbraga@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
