Implemented driver interface for NL command for setting
and getting TX and RX chains. The chains can be set to
either chain 0(1) or chain 1(2) or both(3). This is only valid if
antenna mode is set to 2X2.
Below command can be used to set the chainmask:
iw phy <phyname> set antenna <bitmap> | all | <tx bitmap> <rx bitmap>
Example:
iw phy0 set antenna 1 -- to set both Tx and Rx chain 0.
iw phy0 set antenna all -- to set all/both chains for rx/tx
iw phy0 set antenna 1 2 -- to set chain 0 for tx and chain 1 for rx
Below command can be used to get the chainmask after set:
iw phy <phyname> info
check for "Configured Antennas: TX 0x1 RX 0x1"
Below conditions should be met for setting chainmask:
1. Antenna sharing should be disabled.
2. gEnable2x2 in ini file should be 0
3. enableBTChainSeparation in ini file should be 1
4. DBS should be disabled (gDualMacFeatureDisable = 1)
or HW should be DBS 2x2 capable
5. set TX/RX chainmask 3 in ini (gSetTxChainmask1x1/gSetRxChainmask1x1)
6. HW should support TX/RX chainmask as 3
Change-Id: I04f6667398eac405a6be61bc039e048090578abf
CRs-Fixed: 2693370
RMC is IBSS specific and CFG_RMC_ACTION_PERIOD_FREQUENCY is not used
now so remove the same
Change-Id: Icafff4bd7eb508d92c383861300146e3a0f2def7
CRs-Fixed: 2689882
The roam sequence in LFR-3.0 is roam scan start notification
from firmware followed by roam start indication and then
roam synch,roam synch frame events. Roam start is sent
after candidate selection and host driver will disable
queues when roam start is received.
But for emergency roam trigger, firmware sends roam start
indication directly without notifying roam scan start to disable
data path queues immediately after deauth received from the AP.
So roam start is received before roam scan is started at firmware
and before candidate selection is done.
After roam start notification, host sends scan abort for all scan
on vdev by setting scan command request type to
WMI_SCN_STOP_VAP_ALL. This results in roam scan getting aborted at
firmare in emergency deauth roaming case and roaming fails.
Define new vdev id value based on which the scan module will
abort only host triggered scans setting the request type to
WMI_SCN_STOP_HOST_VAP_ALL in the scan request.
Change-Id: Ie8b005285973461f654329e1b2dc1a45205331f5
CRs-Fixed: 2644323
Currently, the driver trims the channel list with
the PCL if external acs policy ini is set, and
if the channels are unsafe then that can lead
to 0 channels and the SAP can fail.
Fix is to check whether the force SAP start ini
is set and override the channel.
Change-Id: If245bf27deda0f6022343d7a175520fdd92d106b
CRs-Fixed: 2667742
Add ini support for DFS Channel Ageout Time, the time upto which
DFS channel information such as beacon found is remembered.
This ini is used to set the ageout timer value from host to FW.
If not set, FW will disable ageout time.
This value is sent as a WMI_PDEV_PARAM_SET_DFS_CHAN_AGEOUT_TIME
as part of WMI_PDEV_SET_PARAM_CMDID.
Change-Id: I99553fa87a4025f03c52b4b387a414ba06c2c457
CRs-Fixed: 2625996
Introduce ini for roaming_triggers to enable/disable specific
roaming triggers. This will be the master ini to control roaming
triggers. If this ini is set to zero, roaming will not be enabled
on the sta interface unless its enabled via vendor command.
A new roaming trigger - Sta kickout roaming is introduced in
firmware, include this bit support also in the ini.
The value of this ini will be sent over the wmi command
WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID during RSO start.
Reset this value to 0 during RSO stop if RSO stop is due to
disconnect or roam synch failure.
Change-Id: I02f207cdde9d8fb68cd91fab07572baa9e7ac50d
CRs-Fixed: 2631712
Currently, if roaming happens roam reason is not sent to AP. AP will
not able to know why roaming happened. As roaming is offloaded to
firmware, firmware will include roam reason vsie based on driver
indication by vdev param
WMI_VDEV_PARAM_ENABLE_DISABLE_ROAM_REASON_VSIE based on
below conditions:
Parse the QCA attribute CONFIG_ROAM_REASON to control
inclusion/exculsion of roam reason vsie dynamically. Vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION can control roam
reason vsie inclusion using QCA atrribute CONFIG_ROAM_REASON.
Different operations required to implement this feature can be
specified in QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON, so driver parses
CONFIG_ROAM_REASON, updates enable_roam_reason_vsie and indicates to
firmware by updating vdev param.
a.) If Userspace wants the firmware to include roam reason in reassoc
frame, it can send QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON with
value 1 and driver will update enable_roam_reason_vsie to 1.
Driver will update vdev parameter
WMI_VDEV_PARAM_ENABLE_DISABLE_ROAM_REASON_VSIE, so that firmware
can include roam reason vsie in reassoc frame during roaming.
b.) If this command is not issued, the default behavior of the
firmware is not to include err reason code in beacon report
response. Driver will send default value of
enable_roam_reason_vsie to firmware which is 0.
c.) The userspace requests the firmware to stop roam reason vsie
reporting when roam reason is not required for AP anymore. If
userspace doesn't want the roam reason inclusion, userspace can
send QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON with value 0 and
driver will update enable_roam_reason_vsie and notify firmware to
exclude roam reason.
If userspace requests the driver to get the status of
enable_roam_reason_vsie , to check whether firmware includes roam
reason vsie or not, driver will fill CONFIG_ROAM_REASON attribute and
will update to userspace.
Change-Id: I063c822e99fd6908bd4188b429ffa6a2031cee5d
CRs-Fixed: 2624713
Clear sae_single_pmk info while processing del/flush pmk command
from supplicant, if required.
Change-Id: Idd974822ef0426461cd9971e54d8244d64b246b5
CRs-Fixed: 2616036
Requirement is to allow station to just keeps only one
PMK1 and PMKID1 which gets derived while first connection
and re-use it for roaming to other AP which has some
specific VSIE.
To support this feature, STA should Set new flag in 11i
params during RSO start/update when initial connection is
completed based on the VSIE in AP beacon/probe response
frame. This flag will allow fw to roam to AP(s) which has
VSIE with single PMK.
Update PMK info in RSO start command with
sae_single_pmk info if initial connection is completed
with AP contains VSIE.
Change-Id: I839b48da48f92f24444e69405d87560186d7f986
CRs-Fixed: 2616029
Requirement is to allow station to just keeps only one
PMK1 and PMKID1 which gets derived while first connection
and re-use it for roaming to other AP which has some
specific VSIE.
To support this feature, STA should:
1. Set new flag in 11i params during RSO start/update when
initial connection is completed based on the VSIE in AP
beacon/probe response frame. This flag will allow fw to roam
to AP(s) which has VSIE with single PMK.
2. STA should dynamically enable this feature if below
vendor specific IE on AP’s Beacon or Probe Response at
the first connection:
Category Data
Type 0xDD
Length 0x05
OUI 0x00 40 96
Type 0x03
Data Don’t care
(EX, 0x05)
Maintain a separate pmk information structure to support sae
roaming using single pmk.
Change-Id: I0aac7659cecd4d8aaff86c9715e512cf46f22615
CRs-Fixed: 2616035
In FTM mode, no peer is created in the host. Currently, since
peer_unmap_conf_support feature is enabled, FW is expecting
WMA_SEND_PEER_UNMAP_CONF from host to remove the peer Id from AST.
But host never send this WMI CMD in FTM mode.
Disable peer_unmap_conf_support in FTM mode which allow FW to
delete the peer Id without any WMI CMD expectation from host.
Change-Id: Idf9082adc81187346563f3aedf1f1657164f03cc
CRs-Fixed: 2608929
6Ghz SAP needs to send either a probe response or fils
discovery at every 20ms.
Add a new ini to configure the probe response or
fils discovery frame.
enable_6g_sap_fils_discovery=1 sends fils discovery frame
at every 20ms.
enable_6g_sap_fils_discovery=0 sends probe response frame
at every 20ms
Change-Id: I6c5fb339135cf11be071d73970ea3704441380eb
CRs-Fixed: 2586524
Currently, There is no support to disable ring buffer. Each Ring
buffers is using 2MB and overall 10MB is consumed by 5 ring buffers.
Fix is to add ini support to enable/disable ring buffer.
Boolean ini CFG_ENABLE_RING_BUFFER is added. Default value of
gEnableRingBuffer is 1 which indicates that ring buffers are enabled
by default.
CRs-Fixed: 2592476
Change-Id: I30f95668de6df96e5c388e92e202f8c236132dc2
Currently, after FINAL_BMISS detection, FW does channel map
based partial scan followed by one full scan if no candidate
found in partial scan to ROAM to another available AP without
disconnection. This results in additional delay by HOST in
issuing disconnection after a heartbeat failure.
Add INI support (bmiss_skip_full_scan) to allow FW to decide
whether firmware does channel map based partial scan or partial
scan followed by full scan in case no candidate is found in
partial scan after final BMISS.
Change-Id: I48f9bb43bb7933e9ff173f618586ea5986530dcd
CRs-Fixed: 2578848
Currently, default MGMT retry limit is 4 which means 4
transmissions are supported for any management frame.
In noisy environment, Chances to get connection failure
are higher with 4 retransmissions.
Fix is to add INI support mgmt_retry_max to make
CFG_MGMT_RETRY_MAX configurable. Default value for
CFG_MGMT_RETRY_MAX is 15 to reduce the chances of connection
failure in noisy environment.
Change-Id: Id50cb68813fba517a8a1580a3d6662c73b0a381e
CRs-Fixed: 2575385
The event WMI_ROAM_STATS_EVENTID is received after
every roam, once the roam synch complete is sent by the host.
This event contains details regarding the roam trigger reason,
values associated with the trigger, roam scan candidate info,
roam status, roam failure reason.
This helps in debugging/understanding the scenario when roam
failure happens.
WMI_ROAM_STATS_EVENTID Format:
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
roam_stats_event_fixed_param |-> Contains vdev id and number of
| roams detail.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
roam_trigger data TLV |-> Has details on the roam trigger
| reason. Number of roam triggers
| TLV detail is present in the
| fixed param. Maximum 5 roam
| per event is supported
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_scan_info TLV |-> Has details on the roam scan -
| scan type, rssi threshold,
| reason.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_scan_channel_info |-> Has details on the roam scan
TLV | channels. Number of channels
| per trigger is found on the
| wmi_roam_scan_info TLV.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_ap_info TLV |-> Has details on Roam candidate
| APs found during scan. Number
| of roam candidate APs per
| trigger is found on the
| on the wmi_roam_scan_info tlv.
| Max 8 candidates are allowed
| per roam scan.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_result TLV |-> Info on roam success or failure.
| Fail reason, if roaming failed.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_neighbor_report_info|->After roaming, firmware sends
TLV | neighbor/btm report to roamed AP
| to get list of roam candidates.
| This tlv provides info on this.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_neighbor_channel_info|-> This has the info on the
| channel list received as part
| of BTM/Neighbor report.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Print the info received as part of this event into kmsg.
Featurize all the function defines for this roam logging under
WLAN_FEATURE_ROAM_OFFLOAD flag.
Change-Id: Iddc70b572f2e3dc47f08fd1c3c3597cb44981a17
CRs-Fixed: 2576222
As part of Ie9ffc701d93ed1c050375dd56151b7a0da69cdce the STA mode
channel change was added in disconnected state for spectral scan
test at CV2X platform.
Now with iwpriv wlan0 setMonChan on STA mode, a monitor mode
pe_session is created in PE/LIM which take ref count with
WLAN_LEGACY_MAC_ID. As the interface is STA type this session
is not deleted when vdev is deleted. This lead to vdev ref leak.
This code is broken and is no longer in use and cause vdev
ref leak when executed. Thus revert
Ie9ffc701d93ed1c050375dd56151b7a0da69cdce.
Also move the lim session create to hdd_set_mon_rx_cb during
vdev create, as it is deleted during vdev delete.
Change-Id: Ib60aa2bd2746a8cd17f20efa7506c18784a42630
CRs-Fixed: 2557160
Currently in hdd_adapter, the variable sta_info is an array of
hdd_station_info structured indexed by the sta_id. As sta_id is no
longer used this array based implementation becomes unnecessary.
Move the sta_info implementation to a hash table implementation.
Change-Id: I7d6fe04b7e0ab22615d431de9a10a4ad38ed65ba
CRs-Fixed: 2514280
Based on the ini "ignore_fw_reg_offload_ind" ignore regulatory
offload indicatin from fw.
Change-Id: I6e20f2100eeac8e93baa5c5d3f3d1c8b33356aed
CRs-Fixed: 2532989
Update the mac, phy, mcs, nss caps of bands
2.4ghz, and 5ghz for HE capabilities in the
wiphy structure to inform userspace about
the driver capability.
Change-Id: I9fb1233e5396bf3ea411c057af9cbcd5b358271c
CRs-Fixed: 2486266
Currently the host driver blocks roam scan offload command to
the target if the connected akm is OWE or SAE.
Add changes to read the WMI_SERVICE_WPA3_SAE_ROAM_SUPPORT and
WMI_SERVICE_WPA3_OWE_ROAM_SUPPORT service capability advertised
by the target and set it to the mlme fw_akm_bitmap. Read this
bitmap in csr_roam_offload_scan() to allow RSO command.
Also the connected akm is sent to the target via the
WMI_AP_PROFILE command. Translate the CSR akm type for OWE and
SAE akm also.
Change-Id: I68527722ab099e0c8e1681ed64ea416b9a6e9936
CRs-Fixed: 2491021
Do not configure legacy rate to FW if it is HE connection, otherwise
FW does not work.
Change-Id: I31d167ee79b7b58cabad29e65cf6834a7151093d
CRs-Fixed: 2472811
Add ini support for FIPS 4-way hanshake offload to firmware. FIPS
offload feature will add support to handle LFR 3.0 connection only
(auth/reassoc). If this ini is set then firmware will offload
4-way HS to supplicant. In the Roam sync indication firmware will
inform connected and not authenticated so that supplicant can take
care of 4-way HS.
Change-Id: I3da58910218ffc57094cac4c3cab4572631d9404
CRs-Fixed: 2459182
Add support for roaming in case the driver
detects a nud failure. The STA then would roam
to another BSSID, else if the roaming gets failed
the STA would remain connected to the same BSSID
as connected before.
Change-Id: Idbc99b0ce2f9cacd97564dd8cf9892120958eda2
CRs-Fixed: 2461675
Disable OCE in STA vdev if any sta gets associated to SAP/GO.
This will improve the scan results in STA interface.
Without this fix firmware will do probe request deferral for 15ms
out of 28 ms , so 15ms is gone and rest is not sufficient dwell
time to get all AP probe responses.
Change-Id: Ie6f79c86025c53360c792c740a963ed8a1d9b936
CRs-Fixed: 2443190
Propagation from qcacld-2.0 to qcacld-3.0
For the sap role, .get_station would invoke
wlan_hdd_get_station_remote() or wlan_hdd_get_sap_stats(), depends on
"gSapGetPeerInfo" ini setting. And fix the logic of determine sap get
peer info enable or not by target capability.
CRs-Fixed: 2427627
Change-Id: I3162950a6a7202d55b64ff9c60a26971d3a31555
Currently, only broadcast disassociate is supported and deauth is
send in a unicast manner.
For enabling broadcast deauth support, bypass the unicast deauth
and directly send broadcast disassociate.
Change-Id: Ie196bc955b5b9a9f48a474e5f109b2a6c73fa208
CRs-Fixed: 2420980
Legacy WNI CFG items are refactored into new CFG implementation.
PMO uses a wma callback which uses cfg_get API to get listen
interval. Listen interval is now part of the MLME component's
private object. Define API's to get this value and use it instead
of the callbacks.
Remove WMA callback implementation and use new API that gets
listen interval from MLME component.
Change-Id: I797001ea14cc654f9daee3ce297e1ad0c0a08f2a
CRs-Fixed: 2386725
Refactor the below two ini items to new converged cfg/ini
infrastructure:
"gEnableChangeChannelBandWidth"
"extscan_adaptive_dwell_mode"
"extscan_adaptive_dwell_mode" - move this to scm module
"gEnableChangeChannelBandWidth" - move this to mlme
Change-Id: I1ca6657a95c2cd47057f11ccf23c47347f3fc33b
CRs-Fixed: 2394240
Add the WMM config ini config
CFG_TL_DELAYED_TRGR_FRM_INT_NAME to MLME cfg.
Introduce the basic infra APIs related to these configs
from mlme.
Change-Id: Ifaf8072a78f21760e00973e625d7c8e41d8b51a6
CRs-Fixed: 2361533
Remove the following scan and ap protection related ini items:
CFG_AP_ENABLE_PROTECTION_MODE_NAME
CFG_ENABLE_MAC_ADDR_SPOOFING
CFG_SCAN_AGING_PARAM_NAME
Replace the corresponding hdd_config variables and replace
these variable callers with ucfg api from corresponding module.
Change-Id: I99a2659e2151ad285e9451b9e9cc036a199581a3
CRs-Fixed: 2378991
2g vht20 config should be decided by both capability indicated
by target and ini config. Only when F/W indicates 2g vht20
supported and ini config gEnableVhtFor24GHzBand=1, 2g vht20 is
enabled.
Change-Id: I5b7ad8f82b6000096327c501dc84ad05480ef0fd
CRs-Fixed: 2381514
Make changes to the legacy code to support the
new SET KEY converged infrastructure.
Change-Id: Ic5359e3a9035ac5f2a937a9a1013fa92764cda9d
CRs-Fixed: 2358795
Update qcacld driver to move IBSS INI params to converged CFG
component and cleanup HDD ini entriesi
Change-Id: Id8e4c0505113e556a8d64915a648f17fc5c0daf5
CRs-fixed: 2358493
WNI_CFG_WPS_UUID should be refactored and adopted by the mlme
component.
Move the cfg item to cfg_mlme_wps_params.h
Change-Id: I79db155ad16998e9d7a7e20c01efbcba1681d61e
CRs-Fixed: 2366599
Add the functionality changes to replace the legacy powersave
parameters corresponding to the ini values that were converged.
Remove the legacy powersave ini items.
Change-Id: I1da9af9aac4a02a16dc22a43f7f9d526e196d599
CRs-Fixed: 2364964
Add the following WLM and RRM ini configs to MLME
cfg:
CFG_LATENCY_ENABLE
CFG_LATENCY_LEVEL
CFG_LATENCY_FLAGS_NORMAL
CFG_LATENCY_FLAGS_MOD
CFG_LATENCY_FLAGS_LOW
CFG_LATENCY_FLAGS_ULTLOW
CFG_RRM_ENABLE
CFG_RRM_MEAS_RAND_INTVL
CFG_RM_CAPABILITY
Change-Id: I714aca1e9bc6d3c330934753364d7f58d93a28d7
CRs-Fixed: 2353103
Add the following WLAN_REG ini configs and FE_BEAMFORM
cfg items to MLME cfg:
1. WNI_CFG_11D_ENABLED
2. WNI_CFG_11H_ENABLED
3. WNI_CFG_TX_BF_CAP
4. WNI_CFG_AS_CAP
5. WNI_CFG_DISABLE_LDPC_WITH_TXBF_AP
Introduce the basic infra APIs related to these configs
from mlme.
In csr_roam_open_session, lim_populate_vht_mcs_set,
lim_sta_send_add_bss, populate_dot11f_tdls_ht_vht_cap,
populate_dot11f_vht_caps and sme_update_nss, local structure
is updated instead of mlme global structure for vht caps and
thus the mlme vht caps contains only the default values.
Fix this by updating mlme vht caps in mlme_update_vht_cap.
Change-Id: I1a948d7a44ad2bcc7f711c46b278971d7e4026e7
CRs-Fixed: 2354562
Add power items related CFG items in new file,
and store the respective inis in MLME component
Change-Id: Iac183da52495aca07c6270edeb9f383ab49c1ff5
CRs-Fixed: 2341900
Refactor ini items gSapForce11NFor11AC and gGoForce11NFor11AC
into new mlme component.
Change-Id: I85e2f7f9ae14a23c322572290b095aae0f29b0ec
CRs-Fixed: 2354940
Add the following WMM config ini configs to MLME cfg:
1. CFG_QOS_WMM_INFRA_INACTIVITY_INTERVAL_NAME
2. CFG_QOS_WMM_BURST_SIZE_DEFN_NAME
3. CFG_QOS_WMM_TS_INFO_ACK_POLICY_NAME
4. CFG_QOS_ADDTS_WHEN_ACM_IS_OFF_NAME
Introduce the basic infra APIs related to these configs
from mlme.
Change-Id: I149971768a7193099926e2778f093dcd073f0461
CRs-Fixed: 2327692
In mlme_get_wep_key, the key_length is got from the caller is
hardcoded to value 13. This should be updated based on the
length of the key and passed to the caller. But it is not
updated and value 13 is used to copy the key, resulting in
decrypt failure.
Also add debug logs to print wep key id and length.
Pass the key length by call by reference to update the key
length
Change-Id: Ie1e56a80db27894bf9f0426728f9fb74a014679e
CRs-Fixed: 2351182
Refactor HE cap cfg items to new mlme component using
updated cfg architecture.
Change-Id: Ib983d3fc983dfffd2eee7efd1a4e3681d26d84a6
CRs-Fixed: 2351420
