Non raw traffic gets enqueued to VAP in raw mode
and incorrect fc.type causes HW fault.
Lets proceed only if raw frame is of type data.
Change-Id: I9f0d608cd1b319feb9af642969b258aab813645f
CRs-Fixed: 2434391
Add WMI commands:
1) WMI_PDEV_PARAM_SET_MGMT_TTL
Enable/Disable/Set MGMT_TTL in milliseconds.
2) WMI_PDEV_PARAM_SET_PROBE_RESP_TTL
Enable/Disable/Set PROBE_RESP_TTL in milliseconds.
3) WMI_PDEV_PARAM_SET_MU_PPDU_DURATION
Set global MU PPDU duration for DL (usec units)
4) WMI_PDEV_PARAM_SET_TBTT_CTRL.
Set TBTT CTRL value BITS 0 - 2
(refer to WMI_TBTT_CTRL_CFG enum)
Change-Id: Iedda500fdb7bdedcc11fef31f0b29ad3f1812a43
CRs-Fixed: 2415745
Currently with the support of Blacklist manager
component, all the blacklist, avoid list, RSSI-REJECT
list is maintained by the BLM, hence the filter logic
of the blacklist APs in the scan component is not
required.
Cleanup the blacklist BSSID APIs, and related functionality
Change-Id: Ic2f282d9ab7d6d30d87d9718a128cbd8446aff4c
CRs-Fixed: 2464191
During radar table attach, the function to check if EN302_502
pattern is applicable requires actual center frequency of
the current operating channel as one of the inputs.
The caller of this function uses ieee80211 channel as the
argument in the function call.
Call function with actual center frequency instead of
ieee80211 channel.
Change-Id: I9e562863d73c53e4da046eede3e20d8ad9c8f98c
CRs-Fixed: 2454018
In the current implementation, qdf runtime apis invocation
is controlled by macro CONFIG_MCL. So replace the CONFIG_MCL
with the feature flag FEATURE_RUNTIME_PM.
Change-Id: If120c87aa9ed1a0b3e4629c6ee1df4922744656b
CRs-Fixed: 2463188
Channel RF info contains metrics that signify the throughput
availability of all the supported channels. This information
is sent in as discrete TLVs (per channel) as part of the WMI
extended service ready event.
Each TLV contains the frequency, bandwidth represented and
the actual channel metric.
Add support to read the above-mentioned TLVs from the extended
service ready event
Change-Id: If947e179c1ca41466997cc48840a8d36b6236780
CRs-Fixed: 2441921
Add callback to get the roaming status and do not honor addba
response Tx failure.
Change-Id: I148542fc3c629749fc08623f5041f6ca76fee298
CRs-Fixed: 2439721
When RCSA is enabled, if Repeater AP detects radar, the
subchannels affected by radar are sent in addtoNOL IE to the
rootAP as a bitmap. Reinitialise this bitmap for every RCSA to
avoid misinterpretation in rootAP.
Change-Id: Ie6cee841f6f05cfdfc5060afd55b83a34730f31f
CRs-Fixed: 2450786
Add interface API to send reject ap list to FW,
also add the blacklist manager UMAC, and QDF component
for the same.
Change-Id: I826e537683441762043003d71dc2b79ceebebbcb
CRs-Fixed: 2460770
Add CDP support to update vdev stats from the higher
layers.
The CDP API takes a buffer which is then used to
update parts the cdp_vdev_stats structure depending
on the stats ID that is sent through the API.
This change adds support for vdev tx ingress stats
only. Extended support can be added as required
by adding a new stats ID.
Change-Id: I13d6fb946c8a3dbb0b499b7b026d83b080411d15
CRs-Fixed: 2384177
The original version of the QDF trace functionality, introduced in
Change-Id I1d0cdfd8730a5c021aaa50b7dc8549d491d760b3, included a log
filtering mechanism inherited from the MCC code. This mechanism used
an internal table g_qdf_trace_info along with the following APIs which
were used to configure and query the table:
- qdf_trace_set_level
- qdf_trace_set_module_trace_level
- qdf_trace_set_value
- qdf_trace_get_level
Subsequently, as part of the MCC/WIN QDF convergence project,
Change-Id I871c09189202d021405777db732e8821e7aaca7c ("qcacmn: Update
QDF Debug Framework") updated the QDF trace functionality, and as a
result the usage of the g_qdf_trace_info table was replaced.
Since the legacy infrastructure is no longer used, remove it.
Change-Id: I1bb0c0e03c1d1e3227550477779d5db1549ff570
CRs-Fixed: 2461904
current Soc RX defrag lock create/destroy flow as below:
1. dp_soc_attach_wifi3
2. dp_pdev_attach_wifi3-->dp_soc_cmn_setup-->RX defrag lock create
3. dp_pdev_detach_wifi3 (no RX defrag lock detroy)
4. dp_soc_detach_wifi3 --->RX defrag lock destroy
here if step2 is skipped for some failure case, step4 will still
try to destroy RX defrag lock, panic happened.
add dp_soc_cmn_cleanup() function in step3, move RX defrag lock
destroy from step4 to step3 dp_pdev_detach_wifi3-->
dp_soc_cmn_cleanup, also move others like reo cmd lock, tx flow
control related lock.
Change-Id: Ic77ddf21e9cefc6d6b747aaad227c732fa2ae2c4
CRs-Fixed: 2447701
wlan_pdev_chan_match used to take current vdev lock on current
iterating vdev and then on vdev for which channel set is triggered.
If two cores happed to try setting channel on two different vdevs,
cross locking may occur. Fix this by releasing one lock and then
acquiring other lock.
Change-Id: Ic1a6ca448c6d535e949102bc5a8a45971c8babd2
CRs-Fixed: 2460054
Currently the failure in dp_rx_pdev_mon_attach, during
dp_pdev_attach_wifi3, does not cleanup the rx buffers
and hence that memory is leaked.
Follow the proper cleanup sequence to avoid leaking
the rx buffer memory.
CRs-Fixed: 2451982
Change-Id: Idef308e11c46fe3e7ae9199a6fcf05ca83210b6b
Tx completion stats should be counted per wbm ring on tx completion
and not globally. Similarly, rx stats should be counter per reo ring.
Change-Id: I1e4af0d38b23e60de78ca03316861db08ff0811a
For MDM platforms, set default REO destination
ring to SW4 for STA vdev, which is same as SAP vdev.
Note that RX hashing is still enabled for STA vdev.
Also REO destination are run-time remapped when IPA
automony is enabled and disabled.
Change-Id: I49fa523673e7b736008679adec55821e198e8417
CRs-Fixed: 2456786
pm_runtime_mark_last_busy will extend the timer for runtime suspend.
Recording caller and timestamp can help to debug who may prevent
runtime PM suspend.
Change-Id: I4848a2558197e0fc9b7300421a5a1993817333e4
CRs-fixed: 2457803
For PCIe DRV (L1SS sleep) suspend, firmware will trigger a WAKE MSI
to wake up host so that request runtime PM resume for this case.
Change-Id: I959d3b1053b7aef5fe80889553958cf9394c8c38
CRs-fixed: 2450284
Add regulatory rx_ops for setting DFS channels availability to be
called from Offload layer.
Change-Id: I15cec0f119baf5668052618dc3a2552470d1f14f
CRs-Fixed: 2384202
qdf_mem_malloc/free wrappers are using ksize to update the kmalloc counters
of the driver whereas the debug versions of this wrappers are using
requested size itself. To figure out the actual dynamic memory held by
the driver on the debug profile, use ksize for debug versions as well.
Change-Id: I4311f9a450e3fa3e04ac45b1bf7f36a7ff677057
CRs-Fixed: 2449995
__qdf_dma_get_sgtable_dma_addr() iterates through sgl entries
without appropriately checking for NULL pointers before attempting
to access them.
Fix the above-mentioned issue by adding a NULL check before access.
Change-Id: I7456db834f71b9b5cf3cb254526177b9fdcee664
CRs-Fixed: 2448239
Excessive logging during dp init causes watchdog
bite when multiple init-deinit cycle is followed.
Change the loglevel to debug, so that it does not
flood the console with logs.
CRs-Fixed: 2444944
Change-Id: I43daab413800424651e3f5edf558360886d7d7fe
Move WDS feature specific APIs out of common code
as these features are WIN specific. Keep the usage inside
common code under feature specific flags.
Change-Id: Id907a5e22c27fc47e8314449e154525684a27e85
Currently qdf_shared_print_ctrl_cleanup api is defined based on
CONFIG_MCL feature flag, as MCL is not using this api, move
this api under correct WIN specific feature flag
QDF_TRACE_PRINT_ENABLE.
Change-Id: I80117f351e45ad2106524c333f219bba77d49115
CRs-fixed: 2448447
While accessing txrx desc pool, in_use flags is not used and thus
caller may end up using a txrx desc which is not in use. Also
all the params of txrx desc are not reinitialized once in_use flag
is set to false. This can lead invalid pointers used by caller.
So check for in_use flag before using the txrx desc pool, to avoid
use after in_use is set to false and reinitialized all params to
invalid values.
Also In wlan_mgmt_txrx_mgmt_frame_tx driver forcefully get the peer
ref count. It should use wlan_objmgr_peer_try_get_ref api to get
the peer ref, so that after logical delete the frames are not sent
for the peer.
Change-Id: Ie59e622c095750de8eabc49985b114ec6197be00
CRs-Fixed: 2459212
Add support to configure any HAL SRNG descriptor to
be allocated from cached memory area. This is to
optimize of CPU cycles spent on uncached
memory accesses. Also added prefetch of cached
descriptors
Change-Id: I2544e8596d48e2f5549bf687a764c16d73397545
CRs-fixed: 2267945
Add configuration option for enabling/disabling acs channel
grade algo along with configurations channel efficieny
variance and weightages for near mid and far range OBSS
used in algo.
Change-Id: I21fffc6f96d78634bc6ced6ac76a61d87a7d4bb9
CRs-Fixed: 2453992
Peer delete request and response stats has been moved to per vap
stats. The time info on assoc, disassoc and deauth was already
cleaned up, but members in the dp_peer struct weren't removed.
Change-Id: Ie4a1b171178d8ad03abd76069cc0777802814993
CRs-Fixed: 2451766
Clean up of CONFIG_MCL flag and introduce
WMI_INTERFACE_EVENT_LOGGING_DYNAMIC_ALLOC, new speicific-feature
flag for dynamically allocated buffers for debug logging.
Change-Id: Iec4c26faa28400d257332f72dcdf77e18d0fda31
CRs-Fixed: 2450565
For HTT PPDU Stats TLVs, if target has provided less data than expected,
pad the data with zeros until it matches the expected length and
process the TLV, instead of asserting.
This enables testing of different FW and Host versions during regression
analysis.
CRs-Fixed: 2451611
Change-Id: I79aaad8a6fde6d49510c3a212b21425ac784ad5c
qcacld-2.0 to qcacmn propagation
This change adds support for driver supported TCP
delayed ack to increase TCP RX performance in
third-party platform which don't support kernel
TCP delayed ack feature.
TCP delayed ack is dependent on count and timer
values. Whatever is achieved first will trigger
sending TCP ack.
This feature can be controlled through ini values.
gDriverDelAckTimerValue - timer value in ms
gDriverDelAckPktCount - delayed ack count
gDriverDelAckEnable - enable/disable feature
Change-Id: I8105bbb90965295b5a4aefeb00d344a90155974d
CRs-fixed: 2414231
Remove CONFIG_MCL for Serialization msg queue depth and reduction limit to
make code generic. In case SCHEDULER_CORE_MAX_MESSAGES not defined, then
define SCHEDULER_CORE_MAX_MESSAGES to 4000 for WIN . If
WLAN_SCHED_REDUCTION_LIMIT not defined for MCL then define
WLAN_SCHED_REDUCTION_LIMIT to 32 for WIN .
Change-Id: If64f117f6f0af56f6a9e1041e583b022c6c419fb
CRs-Fixed: 2457723
Free the memory allocated for the pdev configuration parameters
during pdev detach so that there are no memory leaks
Change-Id: I856cc6e6082197e98ad105053f1e4cffc2d25c53
CRs-Fixed: 2444000
Implement the interface to transfer the info between
host driver and firmware about the ap which has interop
issues with the DUT. It is detected by firmware and
forwarded to user sapce for persistent storage. User
space configs these APs to firmware when the DUT
starts up next time.
CRs-Fixed: 2425197
Change-Id: I3857d2a605baa2673af333a7a0412f1690b59769
In case of duplicated rx descriptors from hardware,
it will hit issues in __dma_inv_range(), __qdf_nbuf_unmap_single.
Detect the duplicates, skip processing them, drop the mpdu.
CRs-Fixed: 2413816
Change-Id: I7efd4b0c1bda5578578927bb22fe9d487758897d
Legacy code for VDEV_SM is no more used, thus clean up flags
CMN_VDEV_MLME_SM_ENABLE and CMN_VDEV_MLME_CMPT_ENABLE.
Change-Id: I4f7b1099d4929f6250b1868c53b73d7c235a9c22
CRs-Fixed: 2457270
We have a case in which user context was reading
wmi debugfs entries and then an interrupt context
waits on same lock resulting in deadlock and cpu stall.
Disable bh to prevent cpu stall.
Change-Id: I8e2b443317950b4cf2c8c228a98f638dd165ca2b
Remove one possible reachable assertion in case tainted FW
easily trigger the assert and perform a denial of service.
Change-Id: I913d619ab6268c0a843d93ed35c63c79b96ac488
CRs-Fixed: 2428205
