DSI driver did not use msm bus scaling setting,
remove the code.
Change-Id: I71675c8f4e3e97f1ded72ecac3fa87bdc7fb3774
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
The current solution triggers the DMA command and waits till
the command dma done and ISR signals completion. This change
introduces asynchronous wait after a DCS command has been
triggered. Enable this mode only during pre kickoff, so as to not
block commit thread.
Change-Id: Iead7b6328883e844147d47ff68dc878943879553
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
1.Typecast to avoid distinct pointer type comparison
2.Keep DMA mask aligned with api definition.
3.Add Suffix for literals
4.Remove multfrac func to avoid uncompatible division.
5.64-bit division( operator "/") on 32-bit platforms is not supported.
Using platform independent API's here
Change-Id: I0e7305418e53876bd1adf00c1963f85cbdf980cc
Signed-off-by: Ravikanth Tuniki <rtunik@codeaurora.org>
Length of the buffer to be copied is checked
against both source and destination buffer lengths
before copying. This ensures that there is no
buffer overflow while reading as well as writing.
Change-Id: I4bd1a5892b47771aef4c23a4d1594fc1c8361577
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change adds a check for the length of the buffer
before copying it to avoid a buffer overflow.
Change-Id: I146895660be4060d9896706636257a57c6aef94f
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Adding debug, info and error prefix for log messages
in dsi files. To enable debug logs
run "echo 0x1 > /sys/module/drm/parameters/debug"
Change-Id: I438ac16954bd1d39450f8adeb7fb17f9ea6f8140
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Change batches max packet size and read command together, so that
for each esd read, there will not be two independent command transfers.
Without batching sometimes esd thread can hold the panel mutex for
longer time, which can cause framedrops as crtc thread can be blocked on
panel lock to send partial update command and kickoff next frame.
Change-Id: I101283a2559b616911f4312421acb00a8f154dba
Signed-off-by: Vara Reddy <varar@codeaurora.org>
This change is a snapshot of dsi files taken of 4.14
as of commit 764f7c2 (Merge remote-tracking branch
'quic/dev/msm-4.14-display' into msm-4.14)
Change-Id: I8361a844c35a4450f7800964a8da2741676fd6c7
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Change updates frame transfer time calculations. Frame threshold
is provided as input to decide on the final transfer time.
Panel dsi clock node followed by mdp transfer time node
will take priority in selecting final transfer time than frame
threshold time.
Change-Id: I40c3abfc635cd9b338b705535612ac32e047ce6e
Signed-off-by: Vara Reddy <varar@codeaurora.org>
This change adds support for dynamic switching of dsi clocks
to avoid RF interference issues. Also with dynamic dsi clock
switch feature coming into picture, now populate the supported
refresh rate as list instead of providing a range. Modify the
logic to enumerate all the modes in dsi driver, taking dynamic
bit clocks, resolutions and refresh rates into account.
Change-Id: I5b6e62bc935cf2234bdd96fcb3c7537b4e735fff
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Yujun Zhang <yujunzhang@codeaurora.org>
Change updates dsi clock calculations for command mode
as per recommendation. Now dsi clocks are tied to
frame transer time. Propagate correct frame transfer
time to hal to update mdp clocks and bandwidth needed
accordingly.
Change-Id: I46f9038622ddd47cc53c5f3d54229f69a7008c8a
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Remove the redundant register dump sub range
registration for DSI ctl/phy as it needs only
the base registration, since it is considered
as a single block.
Change-Id: I11546bfcde05d02849c53577c4546dcfa9203539
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
