Add WMI unified APIs to extract PNO related WMI events in order to
remove wmi.h inclusion in target_if_scan.c.
Change-Id: I7fd28f175de002b48c294783f69b819ce2f3e37a
CRs-fixed: 2519032
Currently use of comamnd QCA_NL80211_VENDOR_SUBCMD_OEM_DATA
is to pass data blobs from Application to FW but there is
no mechanism to send the data blobs from FW to Application.
To meet the above requirement update the usage of existing
OEM DATA command to use it as a vendor event as well to
send data blob from host to Application.
Change-Id: I8df98f850f4dd56f55dba43c5364a52c425ba9ed
CRs-Fixed: 2573468
After every roam happens or when neighbor report is sent by the
firmware, it sends the WMI_ROAM_STATS_EVENTID to host.
Add support to handle WMI_ROAM_STATS_EVENTID event from target
after every roam.
Change-Id: I4474135ac64ebfb17109d503fbd1c3d637457a73
CRs-Fixed: 2576258
Enhance scan debug log to capture
dwell time for different bands and
capture more information from scan
request.
Change-Id: Ib7af7c1841d0276da884eb30a2c2cf0aaedf4407
CRs-Fixed: 2575569
To enhance visibility of 6GHz AP, 6G only AP shall send
Fils Discovery frame periodically in one beacon interval.
Change-Id: I51487380fca10418d2260dc2612e2adcf6cbb93b
CRs-Fixed: 2562434
Add new stats_id WMI_REQUEST_MIB_STATS &
WMI_REQUEST_MIB_EXTD_STATS in WMI_REQUEST_STATS_CMDID
to retrieve MIB statistics from fw.
Change-Id: I17bccc2673d1a2ce035db04d8426bab49db80790
CRs-Fixed: 2548165
Currently the driver doesnot support the sending and receiving of the
ani level from the firmware.
Add WMI and driver framework support to fetch the ani level.
Change-Id: Ib8271a2b7f62bafb22429113fbfb405cc81379ed
CRs-Fixed: 2554677
This print is a debug measure that addresses an issue where the
HE MCS NSS Map is set to an invalid value. Although rate checks
exist already which take corrective action, this proactive print
adds information useful for addressing corner cases should
they appear.
CRs-Fixed: 2554277
Change-Id: I8e770639472409d96654dc8652ea8c9d210c4965
Add WMI changes for the API he_muedca_mode
to swicth between manual, host and FW dynamic
muedca param selection.
Change-Id: If43b5da483fe082294bda33f8951187ebc7ea3c7
CRs-Fixed: 2554378
Set WMI_PEER_INTER_BSS_PEER peer flag in the fixed param in
WMI_PEER_ASSOC to differentiate between inter-bss and intra-bss peer.
Change-Id: Ic3f54646bfcf988ce53c3d581bacea65070a5036
1) Add Spectral scan mode and agile center frequency in WMI
commands to indicate the current mode.
2) Obtain the Agile Spectral capability from the chain mask table.
CRs-Fixed: 2455967
Change-Id: I88ba6fc1ecf9b530a6b516d0c1e4ce88702c6d1f
Currently the FW expects the flag of
scan chan cmd to be set if the max BW
is filled for all the channels, which
is not set by driver.
Fix is to set the flag's 2 bit to allow
FW to use the max chanel BW.
Change-Id: Id3ce009fbd3c846713d456436c70b44a44428577
CRs-Fixed: 2550434
Add API to know whether 6ghz is supported. Also add API to know
whether an operating class is 6ghz operating class.
Change-Id: I75747502c0033e31d119e58a2254b220646bba10
CRs-Fixed: 2556998
Add support for 6Ghz short ssid and bssid hint mechanism
as part of scan command.
Change-Id: I53a787d2a1406ffd658dc0765bae1e632b870b36
CRs-Fixed: 2559877
Add a qdf counter to know number of qmi stats requests. Reset the
counter when WoW is exited.
Change-Id: Ie0c51fbd6eb2e7530dba01912443e7fc85726e52
CRs-Fixed: 2539999
Dump channel frequency and channel tx power before channel
list sent to FW by WMI_SCAN_CHAN_LIST_CMDID.
The channel and tx power log can be processed
by script to do validation.
Change-Id: I20105aff6f4bba6f8ef1a00c2986bf5a3cffc635
CRs-Fixed: 2548256
Add support to scan for the 6GHz band capabilities
IE and parse the IE. Added peer assoc param for updating
the minimum data rate advertised by the peer in 6GHz
Opration information.
Change-Id: Iebb4379d321832f3ed2bcd3174a54843fa2d497c
In tgt layer, rssi_stats are copied by comparing the vdev id
filled in the target layer and last reqested stats vdev id.
But in target layer api, target_if_cp_stats_extract_vdev_chain_rssi_stats
vdev id is not filled and that can lead to wrong stats in the upper
layers.
Update vdev id in the rssi stats.
Change-Id: I6a8bd032152b43b90ffd4acfc760e218bf4bba5b
CRs-Fixed: 2530148
If more than MAX_NUM_CHAN_PER_WMI_CMD are present, wmi buffer size can
exceed the maximum allocated buffer size. So iterate over the channel
list, and send multiple messages till channel list is empty. Also check
if 6 ghz channel is a PSC channel and mark channel flag accordingly.
Change-Id: I977a2d220c750cec1f261377b3838360bd8c0df3
CRs-Fixed: 2522763
TLV and non-TLV definitions of vdev mgr ops are in component_dev,
they are carved out to a separate file in cmn_dev/wmi for adapting
target_if/vdev mgr component, they are made part of same file
which conflicts tlv design. Create separate file for tlv ops
to definitions and enable respective pointers.
Change-Id: I1e67c7c59adee61b4eb46acb8f51a7a6c385f056
CRs-Fixed: 2517009
Add auto PM tag for WMI_WOW_SET_ACTION_WAKE_UP_CMDID command
such that rrm action frame feature can be enabled for runtime pm
as well.
Change-Id: Ife57c127b1af93632722c9b0a861ecf6ab99fda2
CRs-Fixed: 2513510
In direct buffer rx component, it required to pdev id and mod id match
at same time, so use new pdev id conversion backup and convert pdev id
actually.
Change-Id: If53bde84564becd91f2dd0e20b002da2961dccd2
CRs-Fixed: 2528401
Add support for WMI over QMI to reduce power consumption for
periodic stats report.
Change-Id: Ic57b2bd18be803c97ffeea2e0073751d31e02202
CRs-fixed: 2521835
This reverts Change-Id: I6dd3abd61730d8f17d74a11a42978a64853136e5.
wmi_pdev_stats_v2 and wmi_pdev_stats_v1 are defined depends on
specific target, can’t use them directly in our common code,
must use wmi_pdev_stats instead. And use different config to
enable v1 or v2 pdev stats.
Change-Id: I6ad11d723ac0c9ed55a266c204957af706045d3d
CRs-Fixed: 2521638
As a part of 802.11ax amendment, 6GHz band operation is added.
Since the 6 GHz channel numbers are overlapping with existing 2.4GHz
and 5GHz channel numbers, use frequency to identify unique channel
operation instead of channel number. Channel frequency is unique across
bands.
As a part of above requirement, in the existing WMI interface handlers
and related functions, wherever missing, add frequency attributes to
identify unique channel operation.
Change-Id: I7c7542aa8488b4c55764c733590b77c64c397029
CRs-Fixed: 2517900
Enable DISA WMI commands for FIPS CCM test
by moving DISA WMI code to unified tlv files.
Change-Id: I90e82fef0e7e365faa6e15d555bf4d431214e14a
CRs-Fixed: 2516897
Currently the host gets service_ready_event and service_ready_ext_event
during the init sequence as a part of handshake with firmware. As the
size of the service_ready_ext_event exceeds on adding further
parameters, new event is created.
Add support for WMI_SERVICE_READY_EXT2_EVENT to be processed after
WMI_SERVICE_READY_EXT_EVENT based on the service bit
WMI_SERVICE_EXT2_MSG.
Also add support to extract the reg db/bdf version information that
comes inside the ext2 event.
Change-Id: If0b57af362e7eb653f9189b912ec1dd3efb0f731
CRs-Fixed: 2501132
Reduce the log level from err or info to debug so that logs
are not printed on console.
Change-Id: I0d33c2a8f5b4bb4974656ac0d1eb6713a74cb5f4
CRs-Fixed: 2516287
Configuration for Issue:-
DUT configuration:-
1. Configure DUT's country as US where channel 165 does
not support channel bandwidth of 40 mhz.
AP Configuration:-
1 Configure the AP in a country where channel 165
supports channel bandwidth 40MHZ.
Scenario of the issue:-
1.Connect to a diff AP on some channel x with same SSID,
and then roam to this AP.
Observation:-
The DUT would connect in 40 mhz to this AP instead of 20Mhz,
which violates the DUT's country reg rules.
Expectation:-
The DUT should re-connect only in 20Mhz on channel 165, or
only in max BW supported by reg in that country.
Issue:-
The DUT does not consider the max bandwidth allowed for the channel
in the country configured, and allow the re-association only
in the respective bandwidth.
Fix:-
Send the max BW supported by the channels in the current
reg domain to the FW so that it considers the max BW of the
channel and AP capability and then roam in the respective BW
only.
Change-Id: I977090c58e378e83cb5a3ee84a72afd018e8c428
CRs-Fixed: 2508187
Add dfs_set_cfreq2 flag (indicating secondary DFS set) in addition to
dfs_set (indicating primary DFS set) flag in scan channel list update
params to be sent to FW.
Change-Id: I67670f1d5b128c57c0fad03d9f9b14a99f1d38f6
CRs-Fixed: 2496923
If the FW sends a pktlog checksum in the FW ready event, store that in
pl_dev and use it as buf_hdr.version in the pktlog buffer header.
Also, use a new magic value to identify the checksum in the
buf_hdr.version field.
If the FW does not send the checksum, then the existing magic number
and standard version number would be maintained.
Change-Id: Ib08c093a9b54495a2c5b7e0e163207f2b1eb4ce2
CRs-Fixed: 2508828
Set ssid and ssid_len when restart sap vdev. When hostapd set
ignore_broadcast_ssid to 1(zero-len) or 2(zero-content), when we force-scc
or setChanChange to restart sap vdev, if not set ssid and
ssid_len(default 0) in vdev start wmi, then firmware will reply
broadcast probe request since the ssid_len in broadcast probe req is 0
which matches the condition that firmware send probe response, however,
we should not reply with probe response.
Change-Id: I56580529e2b0db673c6b28c75094a7fd225cba77
CRs-Fixed: 2506391
