WLAN RFA is present in another co-processor subsystem.
In order to prevent unclocked access, Wait for SLATE_POWER_UP
event before starting wlan cold boot qmi handshakes.
Change-Id: If24816c270c32c5f0191227ef66bc4a31549c54d
WLAN RFA is present on another co-processor subsystem.
Any error fatal in co-processor subsystem will result in
WLAN reset.
In order to make sure that rf clock/rails are up before
accessing WLAN hardware, ICNSS platform driver needs to
register with co-processor SSR notification and wait for
POWER_UP event before starting QMI handshake.
Change-Id: Idf65e508a09d93e481349afc73de4804c7841111
Send rf_subtype based on dt node "qcom, rf_subtype" to
firmware using QMI_WLFW_WLAN_HW_INIT_CFG message after
qmi server arrive. Firmware will initialize different
halphy code based on rf_subtype sent by host.
Currently, this change will be applicable only for
adreastea targets which can have either slate RF or Apache
RF attached.
Change-Id: Iba327d0c221104a4ebb55a72d42e1a4b8dcb66c3
Icnss and cnss2 driver receives and sends memory size
over qmi to and from wlan fw. This change add maximum
memory size check before sending or receiving fw mem size
over qmi. Also, use QMI_WLFW_MAX_NUM_MEM_SEG_V01 enum as
maximum size limit.
Change-Id: I392bfbbf0359e60bce9e93d909a119e8c72f07d5
CRs-Fixed: 3367408
Add support to configure WLAN_EN_DELAY using sysfs.
When temperature detected is less than threshold
configure WLAN_EN_DELAY value from sysfs if it is
greater than default WLAN_EN_DELAY value.
Change-Id: I94ac0c6bb3bd2bc2da122d3cf1215b8fe964159f
CRs-Fixed: 3230892
Icnss driver indicates vbatt voltage level to wlan fw
based on battery percentage. This change adds power
supply framework code to enable icnss2 driver to measure
battery percentage and update vbatt volatge level to
wlan fw.
Change-Id: I376805da38222a5e7a20ae4a1737bc978ee6a9ae
Signed-off-by: Sandeep Singh <quic_sandsing@quicinc.com>
Use CONFIG_CNSS_OUT_OF_TREE to control if ICNSS family drivers are
built from in-kernel-tree source or out-of-kernel-tree source since
the exposed header files will be in different paths. This is also
for backward compatibility.
Resolve ICNSS compilation issue with msm-5.15 kernel.
Change-Id: I0a94f70c1be659a00f9401e57ee1dd31b6aa82ae
ICNSS_BDF_DUMMY type board data file is no longer used. Hence remove
it. A BDF file with regular name and dummy content should be sent as
dummy BDF instead of just sending a dummy string.
Change-Id: I9bbdf8a59bb178afe8c27e709b3a360c5de4fa68
This change removes vbatt feature code as adc tm
api's functionalities has been changed and no
longer supports vbatt feature.
Change-Id: I431c1dfe1a5529809fd7d68d1cb15632de3b801b
Signed-off-by: Sandeep Singh <quic_sandsing@quicinc.com>
Consider a scenario where WPSS watchdog happens RPROC driver
gets interrupt and notified to GLINK layer(underlying layer
within QMI) now if ICNSS driver tries to send any QMI message
it will fail and ASSERTS. If ICNSS would have received legacy
SSR notifier it could have ignore ASSERT. But there is a race
where ICNSS sends QMI message between GLINK layer received
WPSS down and ICNSS receives WPSS down and ASSERT of QMI
failure cannot be avoided. To resolve this register early
SSR notifier from ICNSS which notifies about WPSS down to
ICNSS before GLINK. Based on that ICNSS can either avoid
sending QMI message or can ignore ASSERT.
Change-Id: Iada85a1bfff6ae420123afc5f86a738b662171fc
This change will add adrastea prefix in fw file path
of adreatea targets. This changes enables fw files
to be picked from /vendor/firmware_mnt/image/adrastea
path.
Change-Id: Ic0ce57b7a8db08e4bf55c8a493a1f1500d93c427
CRs-Fixed: 3140070
Bring ICNSS family drivers from msm-5.10 kernel as of commit
'cb298739ee51 ("icnss2: Download bdf file for helium targets")'
to WLAN platform project.
Updated wlan_firmware_service files and makefiles to support
ICNSS2 compilation.
Change-Id: I02cf792b61772f07ac0607be7bb6b3bfda7815e4
