The 6GHz security check is enabled by default. Disable the check
if RF test mode is enabled.
Change-Id: Id6af514f6a31f6351b1b0d784c2b9f7d301496c0
CRs-Fixed: 3040621
Set gRemoveTimeStampSyncCmd ini to 1 by default so that even for more
than 60 seconds, the device can stay in RTPM WoW mode.
Change-Id: I560389dd9c7d5a33d01c092ad057a7a7aa6f7c37
CRs-Fixed: 3003718
Existing INI disable_4way_hs_offload is defined as a boolean
that controls the EAPOL Handshake to be offloaded to Firmware or
Not. There is no way to specify the EAPOL offload per AKM.
Hence extended the support of EAPOL handshake offload to firmware
per AKM by converting this INI to a bitmap integer.
With ini value as 0 by default Firmware takes care of 4-way HS
during roam for all AKMs except for SAE and OWE. If
this ini value is 1 then Host takes care of EAPOL for all AKMs.
Having the backward compatibility, added a new value to ini.
If this ini value is set to 2 and also if the SAE EAPOL offload
service bit is set by Firmware then the behavior is same as ini
with 0 except that Firmware takes care of 4-way HS for SAE roam
as well. And for OWE it is still handled by supplicant.
To achieve this, new roam offload flag is introduced to indicate
Firmware about SAE roam EAPOL offload, So that in Roam sync
indication Firmware will inform the status as connected but not
authenticated so that supplicant can take care of 4-way EAPOL HS.
Change-Id: I8b65a1768fad91fac7e427712d3ccf4586176f5f
CRs-Fixed: 2955029
Enable 4address frame format for the packets to the AP.
Enable MEC check for the sta dp vdev.
A new ini is added to enable WDS feature specifying the
desired WDS mode.
CRs-Fixed: 2889438
Change-Id: I99ccb91adf283a1ed863902ec4b31f1c3e821d32
Remove all of the conditional compilation for pmf since this
feature is mandatory for future scope from protocol point
of view.
Change-Id: Id3a2127e9ecb343ad2a0354dcbc331c22167d7fb
CRs-Fixed: 2852630
Update default values of INI items to most commonly used values
in WCNSS_qcom_cfg.ini file on commercial devices.
Change-Id: Ibf1e22406951855a4e726fb8105913a53d3c33ee
CRs-Fixed: 2874758
To make it generic, rename the flag QCA_WIFI_NAPIER_EMULATION
as QCA_WIFI_EMULATION.
Change-Id: I8e654262a38a7a701a5a34e2bbd5394c8985c65a
CRs-Fixed: 2871313
Enable periodic time sync between host and fw by setting
gRemoveTimeStampSyncCmd to 0.
Change-Id: I52168ad6d065262c433c801716eec0d7782bf6e8
CRs-Fixed: 2845017
Add new ini "monitor_mode_concurrency" to support this feature
and introduce policy manager api's for concurrency checks.
Change-Id: I35ee1fece0a6f9ae8fe340b0598c4a3e20b17e82
CRs-Fixed: 2814523
Currently, QCA_SETBAND_AUTO is backwards compatible, so it is set
to include only 2G and 5G bands. Update this to include 6G bands
as well. Also update the band capability INI to have the default
value 0 include 6G bands.
Change-Id: I98067c18e939ff4c1e7b1e778b020b44409b5b34
CRs-fixed: 2799883
Increase max sae auth frame retry count to 3 since total SAE auth
timeout is 5s.
Change-Id: I5902cc3411f713eaeed5ef7754fe7fe8e590b459
CRs-Fixed: 2765211
In some instances, AP does not respond to probe req
causing join timeout at STA and no connection.
To solve this,send multiple probe requests(every 200ms)
to AP until join failure timeout(1 sec) expiry,
if single bssid case retry same bss again
(configurable via ini, max allowed tries 2).
Change-Id: I7a7eeedcc24db1a74cd186ff957c638a39cdea6d
CRs-Fixed: 2763815
If join fail reason is timeout, retry sending join req
after timer expiry, timer value can be configured
via join_failure_retry_interval.
Change-Id: If90071b3f6d7f48936db6f7088c3c1547e48b294
CRs-Fixed: 2760236
Host sends the WLAN_MSG_WLAN_STATUS_IND to WiFi Location Service(WLS) via
cnss daemon which includes supported channels. WLS service is yet not 6GHz
capable. Hence to limit the 2.4GHz/5GHz channels only in
WLAN_MSG_WLAN_STATUS_IND introduce new INI "wls_6ghz_capable".
Change-Id: I77b284d2025601fec72aa35d430f18865f15f247
CRs-Fixed: 2748489
CLD driver specific time sync feature is no longer used since
core BSP provides more accurate time sync over QMI and hence
disable CLD driver specific time sync feature to avoid periodic
wake ups.
Change-Id: Ic2790e7cdb6cf56f874fb56cda246777bc34d2e3
CRs-Fixed: 2715021
Change the usage of cfg parameters from Internal/External
to External in .h description for mlme, p2p, and
policy manager files.
External means that both internal teams and external
customers can modify the parameters.
Change-Id: Ic1e68d5a90be2c898ce66aa18e8d91f16561b408
CRs-Fixed: 2712773
The band_capability field is used in other places to be
a bitmap over reg_wifi_band. Update the field in wma_tgt_cfg and
wlan_mlme_generic to take the same bitmap for consistency.
Update all references to these fields to expect a bitmap as well.
Change-Id: I8abd697e2fbe02b4eadd32f3027bef7408bac2a0
CRs-fixed: 2726710
Introduce new INI sae_connect_retries to decide auth (initial connect
and roam auth) and connect retry for sae. MAX reties is capped to 2
and max for roam auth is 1.
Default is 0x49 i.e. 1 retry each.
Bits Retry Type
BIT[0:2] AUTH retries
BIT[3:5] Connection reties
BIT[6:8] ROAM AUTH retries
Change-Id: Idae86a7bdb32244c7f3a140b8591418b8238758a
CRs-Fixed: 2728458
Add ini support for DFS Channel Ageout Time, the time upto which
DFS channel information such as beacon found is remembered.
This ini is used to set the ageout timer value from host to FW.
If not set, FW will disable ageout time.
This value is sent as a WMI_PDEV_PARAM_SET_DFS_CHAN_AGEOUT_TIME
as part of WMI_PDEV_SET_PARAM_CMDID.
Change-Id: I99553fa87a4025f03c52b4b387a414ba06c2c457
CRs-Fixed: 2625996
Currently, There is no support to disable ring buffer. Each Ring
buffers is using 2MB and overall 10MB is consumed by 5 ring buffers.
Fix is to add ini support to enable/disable ring buffer.
Boolean ini CFG_ENABLE_RING_BUFFER is added. Default value of
gEnableRingBuffer is 1 which indicates that ring buffers are enabled
by default.
CRs-Fixed: 2592476
Change-Id: I30f95668de6df96e5c388e92e202f8c236132dc2
Currently, after FINAL_BMISS detection, FW does channel map
based partial scan followed by one full scan if no candidate
found in partial scan to ROAM to another available AP without
disconnection. This results in additional delay by HOST in
issuing disconnection after a heartbeat failure.
Add INI support (bmiss_skip_full_scan) to allow FW to decide
whether firmware does channel map based partial scan or partial
scan followed by full scan in case no candidate is found in
partial scan after final BMISS.
Change-Id: I48f9bb43bb7933e9ff173f618586ea5986530dcd
CRs-Fixed: 2578848
Currently, default MGMT retry limit is 4 which means 4
transmissions are supported for any management frame.
In noisy environment, Chances to get connection failure
are higher with 4 retransmissions.
Fix is to add INI support mgmt_retry_max to make
CFG_MGMT_RETRY_MAX configurable. Default value for
CFG_MGMT_RETRY_MAX is 15 to reduce the chances of connection
failure in noisy environment.
Change-Id: Id50cb68813fba517a8a1580a3d6662c73b0a381e
CRs-Fixed: 2575385
The event WMI_ROAM_STATS_EVENTID is received after
every roam, once the roam synch complete is sent by the host.
This event contains details regarding the roam trigger reason,
values associated with the trigger, roam scan candidate info,
roam status, roam failure reason.
This helps in debugging/understanding the scenario when roam
failure happens.
WMI_ROAM_STATS_EVENTID Format:
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
roam_stats_event_fixed_param |-> Contains vdev id and number of
| roams detail.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
roam_trigger data TLV |-> Has details on the roam trigger
| reason. Number of roam triggers
| TLV detail is present in the
| fixed param. Maximum 5 roam
| per event is supported
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_scan_info TLV |-> Has details on the roam scan -
| scan type, rssi threshold,
| reason.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_scan_channel_info |-> Has details on the roam scan
TLV | channels. Number of channels
| per trigger is found on the
| wmi_roam_scan_info TLV.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_ap_info TLV |-> Has details on Roam candidate
| APs found during scan. Number
| of roam candidate APs per
| trigger is found on the
| on the wmi_roam_scan_info tlv.
| Max 8 candidates are allowed
| per roam scan.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_result TLV |-> Info on roam success or failure.
| Fail reason, if roaming failed.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_neighbor_report_info|->After roaming, firmware sends
TLV | neighbor/btm report to roamed AP
| to get list of roam candidates.
| This tlv provides info on this.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
wmi_roam_neighbor_channel_info|-> This has the info on the
| channel list received as part
| of BTM/Neighbor report.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Print the info received as part of this event into kmsg.
Featurize all the function defines for this roam logging under
WLAN_FEATURE_ROAM_OFFLOAD flag.
Change-Id: Iddc70b572f2e3dc47f08fd1c3c3597cb44981a17
CRs-Fixed: 2576222
As part of Ie9ffc701d93ed1c050375dd56151b7a0da69cdce the STA mode
channel change was added in disconnected state for spectral scan
test at CV2X platform.
Now with iwpriv wlan0 setMonChan on STA mode, a monitor mode
pe_session is created in PE/LIM which take ref count with
WLAN_LEGACY_MAC_ID. As the interface is STA type this session
is not deleted when vdev is deleted. This lead to vdev ref leak.
This code is broken and is no longer in use and cause vdev
ref leak when executed. Thus revert
Ie9ffc701d93ed1c050375dd56151b7a0da69cdce.
Also move the lim session create to hdd_set_mon_rx_cb during
vdev create, as it is deleted during vdev delete.
Change-Id: Ib60aa2bd2746a8cd17f20efa7506c18784a42630
CRs-Fixed: 2557160
Add ini support for FIPS 4-way hanshake offload to firmware. FIPS
offload feature will add support to handle LFR 3.0 connection only
(auth/reassoc). If this ini is set then firmware will offload
4-way HS to supplicant. In the Roam sync indication firmware will
inform connected and not authenticated so that supplicant can take
care of 4-way HS.
Change-Id: I3da58910218ffc57094cac4c3cab4572631d9404
CRs-Fixed: 2459182
Periodic time sync feature is not needed on mainline hence
disable this feature by setting gRemoveTimeStampSyncCmd = 1.
Change-Id: Ifbffc02c61af3be8300a97d9be7b2c7dceaf263d
CRs-Fixed: 2422866
Refactor the below two ini items to new converged cfg/ini
infrastructure:
"gEnableChangeChannelBandWidth"
"extscan_adaptive_dwell_mode"
"extscan_adaptive_dwell_mode" - move this to scm module
"gEnableChangeChannelBandWidth" - move this to mlme
Change-Id: I1ca6657a95c2cd47057f11ccf23c47347f3fc33b
CRs-Fixed: 2394240
Currently, the support for beacon reception stats is only dependent on
the FW.
Add an ini so that the user can also have a control over the stats
Change-Id: I4a1e654b9d1598836378def494b37a997904d77a
CRs-Fixed: 2366473
Add the following WLAN_REG ini configs and FE_BEAMFORM
cfg items to MLME cfg:
1. WNI_CFG_11D_ENABLED
2. WNI_CFG_11H_ENABLED
3. WNI_CFG_TX_BF_CAP
4. WNI_CFG_AS_CAP
5. WNI_CFG_DISABLE_LDPC_WITH_TXBF_AP
Introduce the basic infra APIs related to these configs
from mlme.
In csr_roam_open_session, lim_populate_vht_mcs_set,
lim_sta_send_add_bss, populate_dot11f_tdls_ht_vht_cap,
populate_dot11f_vht_caps and sme_update_nss, local structure
is updated instead of mlme global structure for vht caps and
thus the mlme vht caps contains only the default values.
Fix this by updating mlme vht caps in mlme_update_vht_cap.
Change-Id: I1a948d7a44ad2bcc7f711c46b278971d7e4026e7
CRs-Fixed: 2354562
1) Some CFG INI options' comment text are missing.
Add them so automation script can parse and retrieve the
correct comment text.
2) Fix some discrepancies in existing CFG INI comments.
3) Delete some INI items that are not used any more.
Change-Id: Ia2fc4fab70f78e99d14fd1f7f2b4248e6484ee32
CRs-Fixed: 2350612
Add CFG items of RTT and PMF as generic items based
on converged cfg component.
Change-Id: Ic95d1e7b052259149704d9faf65ebe5f51536fdf
CRs-Fixed: 2313281
