In the case of WCN6450, sizes of the TX descriptor pools are not known
to the driver during load time. The sizes are shared by the firmware
post VDEV creation via HTT_T2H_MSG_TYPE_FLOW_POOL_MAP HTT message.
After the VDEV gets deleted in the firmware, a corresponding flow unmap
HTT message will be sent to the driver to clean up the TX descriptors
of a particular VDEV.
Add logic to handle the flow map/unmap HTT messages for WCN6450. These
messages are specific to WCN6450 and hence the logic is implemented in
arch specific HTT code.
Change-Id: I8edcabbec77abae2c238f487acb7a48b478fd149
CRs-Fixed: 3381751
Set WDI version based on SOC architecture, set WDI
version to IPA_WDI_4 for QCA_WIFI_QCN9224 chipset,
else IPA_WDI_3.
Change-Id: Ib80435e5098cfbcb9f90d4ac9cfe81ea183f308a
CRs-Fixed: 3383949
At continuous physical address limited telematics platform,
in order to avoid occasional memory alloc failure with big
kzalloc size, it's better to use virtual memory allocation
API instead. And below items will be refined to replace
malloc with valloc if CONFIG_ENABLE_VALLOC_REPLACE_MALLOC=y.
1 x 30488 = 30488B @dp_soc_attach:15189
1 x 52096 = 52096B @hal_attach:1104
4096 x 64 = 262144B @dp_rx_desc_pool_alloc:337
Change-Id: I57a6f78f690b5be1838de954933ae36129cea234
CRs-Fixed: 3426935
1. Add an API to process trigger_umac_recovery T2H message.
2. Synchronize do_pre_reset, do_post_reset_start, do_post_reset_complete
messages for all the SOCs and then process these messages in the host.
3. Synchronize pre_reset_done, post_reset_start_done,
post_reset_complete_done for all the SOCs before sending it to FW.
4. Add a new state in host for trigger_umac_recovery message.
Ignore back to back trigger_umac_recovery messages received from FW.
Change-Id: Id45d326d63e122834090844e83ad6cc7240f96af
CRs-Fixed: 3425833
Support REO2SW ring pointer update threshold configuration,
it is helpful for PCIe utilization improvement.
timer based threshold - M: issue pointer updates when M micro
seconds has elapsed.
number based threshold - N: issue pointer updates when N entries
updates occur.
Change-Id: I49ed388520fd52e97e303d6ea9c04ced6cb5cf5f
CRs-Fixed: 3420101
Add support to enable/disable MLO Link Peer stats through
ini and cfg80211tool enable_ol stats command
Change-Id: Id1229a149befa416d060e1b07eee150e6b295abf
CRs-Fixed: 3397721
1) Allocation of memory to hold MLO Link Stats
at MLD Peer level.
2) Modify the Macros to update MLO link stats.
3) Init and reset the Stats
Change-Id: Id4e9d40e212c5093159ae0c7d6316e93d19cf928
CRs-Fixed: 3397721
Add HMWDS rem-addr support to delete AST WDS mac entries in
Beryllium chipsets.
Change-Id: I5623bac02b326d1d668ad5e1fdcfc3a9f8cbbb9c
CRs-Fixed: 3397961
Currently, there is a compilation error on the
OWRT SI in the alternate code path when optional
dp feature is not enabled.
The caller wlan_ipa_wdi_init_set_opt_wifi_dp() passes an
argument of incompatible type. This change fixes the
compilation issue.
Change-Id: I1f2eecbb67bfb2ef17ee73ce2faedb85827b4bbc
CRs-Fixed: 3417214
This change adds the optional wifi datapath feature
to transfer data to and from modem via WLAN.
By using the existing path between WLAN and IPA, this
change registers new interfaces between IPA and WLAN
to reserve, add, delete and release rx filters,
which are required for setting up CCE filter rules.
These filters help to determine which packets need
to be routed to IPA specific REO rings.
Change-Id: I17c2ab77ae343f15d6b79fa02bb70ed62294089c
CRs-Fixed: 3403314
Make DP changes for handling umac reset in QCA5332.
Changes are done to program msi_data value of the IPC interrupt to FW.
Change-Id: Ib6453755e191da655b87b528a7cef38a464f316b
CRs-Fixed: 3401146
Add cdp layer API to get stats and
Copy pdev deterministic stats from dp_pdev to cdp structure
Change-Id: Ia7dbbe4cfe7ebe66a040879144505b17aaaa625a
CRs-Fixed: 3380939
Add cdp layer API to get stats and
Copy peer deterministic stats from dp_mon_peer to cdp structure
CRs-Fixed: 3380939
Change-Id: Ic90b9c9f5c7463ad0d5b7c2bb7a371e4d4fef070
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/dp_main.c, so fix those issues. In addition,
there are a number of instances where public functions have their
implementation documented instead of having their interface
documented, so remove that documentation. The documentation at the
interface will be added separately if it is not already present.
Change-Id: Id9bcfd37d690b72ec7a04f25d1b91b0210bef8e3
CRs-Fixed: 3373154
Target is sending interrupt even interrupt handler is not
registered for the vlan RX DST ring, and causing kernel crash.
Fix is to disable the IRQ line if host is not supposed to handle
the interrupt for vlan RX DST ring.
Change-Id: I91b8a5784969e1022d283793905c33340492706b
CRs-Fixed: 3348574
change allocation location for reo qref table.
per probe allocation results in mem alloc failure when
frame is fragmented
Change-Id: I5922bddebcd0577ba38734ae7d4194d726d825aa
CRs-Fixed: 3326520
The function dp_print_mlo_ast_stats() is currently a public function.
However this function is only called from within the file where it is
defined, so make it static.
Change-Id: Id83c7b3110c60ca6e3dc3263aaf87d21e9365a31
CRs-Fixed: 3374039
Current rx_mpdu_received and rx_mpdu_error stats reporting is incorrect.
rx_mpdu_received would be rx_mpdu_delivered + rx_mpdu_errors.
Also get combined rxdma_errors(rx_mpdu_errors) handled across host and FW.
Change-Id: Icbfeaffd7cd27d7f894df2d39add9cc7b47714be
CRs-Fixed: 3333010
Add history to record the config/control events
e.g. peer create/delete/unref-delete, vdev attach/detach
in datapath.
Change-Id: Ic3c8122fca9124e41931ec445946aec5e8863434
CRs-Fixed: 3371899
Add debug logs in the MLD peer create/delete path
to help debug any issues with MLD peer leak.
Change-Id: I63126d9b86f3179a88809836371fc765d340b6d8
CRs-Fixed: 3379148
from Beryllium onwards a single Flow Search Table
will be used across multiple radios. to ensure this
a single FST attach is called for the first SOC's
pdev and FST detach is called only during last pdev
of last SOC. the same FST instance is saved in all
pdevs of all the SOCs
CRs-Fixed: 3366409
Change-Id: I42fbdc6f09fb902021877e100a2831a1a24bc975
An INI dp_tx_spl_device_limit is defined and can be used to configure the
limit of TX descriptors that can reserved on the SOC to handle
special frames like EAPOL.
CRs-Fixed: 3343207
Change-Id: Ic84a11249880a3541749a72ac6d60df548f2bc5c
An INI dp_tx_spl_desc is defined and can be used to configure the
limit of TX descriptors that can reserved on the pdev to handle
special frames like EAPOL.
CRs-Fixed: 3343209
Change-Id: I6578bddd1f4ea07528c9f66f778b113ec6fb9e61
Add get parameters for features. These flags are
set in datapath vdev object and need to be extracted
outside datapath.
Change-Id: I4b4d8adcc523fc030bca699e0f0f9eb10475920c
CRs-Fixed: 3367490
REO module may hang when REO commands are queued after WoW enable WMI
sent to FW. Change is used to check WoW progress before accessing REO
CMD ring. If WoW is in progress, then defer REO commands.
Change-Id: I9cd8390e77ef33f98f84cb604f152e3f9a0e4203
CRs-Fixed: 3362608
In case where memory alloction failure for RX TID return
appropriate status for CP
Change-Id: I96a3694b05f84034ebacd15d87e58cd1f59207de
CRs-Fixed: 3365642
Special frames like EAPOL should not be dropped as it would cause
failure in connection. To prevent the dropping of higher priority
special frames, reserve a set of descriptors from the tx descriptor
pool.
Check the regular soc or pdev limit for the allocating tx descriptors
for the regular packets and use the reserved set of descriptors
only for the special packets.
CRs-Fixed: 3331359
Change-Id: I15532fb5e325ba6ad997090008bda8c52707a05b
1. Change the names of parameters and functions related
to direct switch feature from ppe to ppeds
2. Remove the unused ppe_release_ring
Change-Id: I5a95b1273e338f354903af98158578ac65758a8a
CRs-Fixed: 3345097
Issue:
When DS mode is configured for a VAP
in both AP and STA (RDP 433), the tput reduces.
For instance, for an ingress of 7G
in standalone case, the egress rate is
1) 6887 Mbps when DS is enabled only in AP
2) 1900 Mbps when DS is enabled in both AP and STA
RCA:
With the help of debugs & proc/interrupts, identified
that we are not setting up the peer when the
device in STA mode due to AP mode check in
dp_soc_txrx_peer_setup.
Hence, the traffic is not flowing via DS
and so, tput reduces.
Fix:
Added changes to invoke txrx_peer_setup in
STA mode and DS mode will configured in that mode.
With the fix, traffic flows via DS, which
in turn improves the increased
Change-Id: Ib51e9a27e5078ed99160f213ddffed801c2e4ecf
CRs-Fixed: 3355603
