Add vendor command QCA_NL80211_VENDOR_SUBCMD_COAP_OFFLOAD to
enable/disable offload processing in firmware for CoAP messages
(RFC7252: The Constrained Application Protocol) or fetch the
CoAP messages cached during offload processing.
Change-Id: I2eaeba58ec6bc44738f68eb00c36ebdce2eae6f8
CRs-Fixed: 3193633
UMAC reset prerequisite setup command contains the following information.
- Interrupt number to be used for raising the UMAC reset interrupt
- Address of the shared memory
This is an HTT command. Send this command as part of the UMAC reset
initialization sequence.
Change-Id: I7a08f48b420580b5e3dbb9b46f6605d986f8fd89
CRs-Fixed: 3244930
UMAC HW reset is expected to send the following Tx commands to the target.
- PRE_RESET_DONE
- POST_RESET_START_DONE
- POST_RESET_COMPLETE_DONE
Add the necessary logic for the same.
Change-Id: I2450ed9281691abcc064661d4481ae78f48a0f3d
CRs-Fixed: 3244895
UMAC HW reset is expected to receive the following 3 events from FW.
- DO_PRE_RESET
- DO_POST_RESET_START
- DO_POST_RESET_COMPLETE
Add necessary logic to handle these events.
Change-Id: I786ecf6ed2925fd7fcc0934fdce65c76784f4f67
CRs-Fixed: 3244865
In IPA offload, both tagged and untagged traffic cannot be handled with
a single rx pipe. Hence, add support for 2nd RX pipe for tagged and
untagged traffic respectively.
Change-Id: I77ff633327696f66df42fb592492321c1591646b
CRs-Fixed: 3226021
Issue: mode was set to HT20 and marksubchannel was enabled. We injected
radar into the HT20 primary channel. The primary channel is not being added
to NOL when marksubchannel is enabled because the current subchannel
frequency list(freq_offset->freq[i]) is not being filled.
To fix this, Even if it is an HT20 mode, fill the subchannel frequency
list(freq_offset->freq[i]) based on offset.
Change-Id: I571ba60c755e7701a21db89f917c953ffa9716a6
CRs-Fixed: 3244971
Add support to log latest CE descriptor history which helps
to identify CE scheduling/reaping delays when full debug
history dump is not available.
Change-Id: I44a5c86a3e1dd4861bfd2e77b3f772d5d53bcedf
CRs-Fixed: 3225155
Currently in monitor mode for KIWI, interrupt for RXDMA2HOST is
enabled to process both monitor status srng and montior destination
srng, but low threshold interrupt for monitor status srng is also
enabled. so when available RX buffer in monitor status srng is less
then low threshold, it is possible that two kind of interrupt from
RXDMA2HOST ring and monitor status ring will call
dp_rx_mon_status_process_tlv() in different context and access to
mon_pdev->rx_status_q at the same time, this will lead to skb
double free issue.
solution:
(1) disable RXDMA2HOST srng interrupt in monitor mode.
(2) enable monitor status srng batch count interrupt for monitor
processing.
Change-Id: I1df8830cb7cc55468e5df5e49045c3d96f7c29a8
CRs-Fixed: 3245393
In case if cm ctx is NULL, the disconnect state check API is returning
false which makes the caller assume vdev is not disconnected.
Hence, change the return value to true in this case.
Change-Id: Iadd52d94d6f561974101aa245ddbfdb1eb301b06
CRs-Fixed: 3246161
Add change to support learning of AST entries on host
for BE platforms(Waikiki) based on peer map and unmap event received
from FW.
Change-Id: I58aa6a18ca69d5ffc6fbcf9c18723adb39647950
CRs-Fixed: 3237934
From firmware perspective, host only sets 5 GHz regdomain hence 2 GHz
uses default setting and firmware does not update channel list event
for all phys according to the new country code.
Therefore sets pdev_id to 0xFF in function reg_set_country and it is
mapping to WMI_PDEV_ID_SOC when issue wmi command
WMI_SET_CURRENT_COUNTRY_CMDID as firmware required.
Change-Id: I0eb84db9f6d77c0473161cc4ffc0dcebd31c3d45
CRs-Fixed: 3239644
As part of IPA offload support for WCN7850 chipset, properly define
TX ring indexes into soc->tcl_data_ring[] and soc->tx_comp_ring[]
used by IPA.
In the change, use wlan_cfg_get_rbm_id_for_index() to get correct
rbm values for WBM2SW ring used by IPA.
Change-Id: Ie5b6743c1cb2adfa156735fc84dc1429a67f833a
CRs-Fixed: 3246038
The roam reason and roam sub-reason code sent and expected
reason codes at supplicant are diffent which results in
wrong interpretation of reason code.
Add roam reason and roam sub-reason code enum in order
to aid the converion from fw roam reason code to supplicant
understandable reason code.
Change-Id: I3432793965e325ddbf90ab90a1532a0726650d8c
CRs-Fixed: 3238496
In current code, assoc peer is designated as primry umac,
on primary umac allocation, primary umac bit gets reset.
But in force umac case, primary umac bit not getting reset.
This change resets primary umac bit of assoc peer, if
assoc peer is not designated primary UMAC.
Change-Id: I640433548b9efeb20ba2b23f8d1141cc5505087b
CRs-Fixed: 3243326
On receiving the peer unmap event the ops
is called without the mac address of the
peer for which peer unmap is received.
Add mac address of the peer for which peer
unmap is received.
Change-Id: I9026433089963818d5a227a0660866ff504dea84
CRs-Fixed: 3238626
Currently, in wlan_defrag_elemsubelem_fragseq() API,
there is possible buffer over-read in fragbuff buffer.
Buffer may have a malicious length larger than their
payload size, which leads to a buffer over-read during
defragmentation.
Fix is to validate the fragment length against the buffer
boundary in util_get_successorfrag().
Change-Id: Ia9e688a0ab17954eb464ec586820bb95b51f12d1
CRs-Fixed: 3236560
Add following fixes for STA to support and operate in
eMLSR mode
1) Update and send eMLSR cap flag to FW even in vdev start
request on both links.
2) Copy EML caps to wmi peer assoc mlo params to send it
to FW.
Change-Id: Ic17b9b82809659d7a4392c09eceecae7c53b2049
CRs-Fixed: 3237737
Add feature flag to indicate support for sending authentication
frames with Link Address.
Change-Id: Ifbd28b8d474b28b0e85a23c9c91ebccedb381d9c
CRs-Fixed: 3239304
Firmware advertises WMI_SERVICE_DELETE_ALL_PEER_SUPPORT
capability to indicate vdev peer delete all command support.
PASN peer relies on the WMI_VDEV_DELETE_ALL_PEER_CMDID
command to delete the PASN peers before vdev delete.
So allow PASN peer create only on targets that advertise
WMI_SERVICE_DELETE_ALL_PEER_SUPPORT.
Change-Id: Ib94d9e14e34dd1e5c25bf6946e0d59fe83fd6dd3
CRs-Fixed: 3229438
Select best candidate by mlo score algorithm.
Check bss mlo type first by mlo info, mlo config, partner frequency and
dbs/sbs cap, calculate candidate score for SLO/MLMR/EMLSR bss types.
For SLO case, same as before except:
Decrease percent of legacy band and nss to include 320M and 8x8.
Decrease max percent of congestion from 100 to 80 to include MLMR joint
congestion.
Increase weight of both band width and nss to 20.
For EMLSR case, same as SLO except adding EMLSR boost score.
For MLMR case, besides adding MLMR boost score,
calculate joint RSSI/band width/congestion score for combination of
scan entry + each partner link by new mlo algorithm, select partner with
highest total joint score as candidate combination, only activate that
partner link.
Change-Id: I640c6825d945caf5fab504a77717195c2eac0c93
CRs-Fixed: 3234912
Add mld config checks in osif_vap_create_check and fail
once the config is invalid.
Change-Id: I26c3b4719fa9b18be0a4590861c654504fb3e6bf
CRs-Fixed: 3200923
btcoex status is not extracted in the extract_roam_scan_stats_tlv()
which was required for ROAM_SCAN_DONE event logging due to
which wrong status is printed in ROAM_SCAN_DONE
logging.
Extract bt_coex status in the extract_roam_scan_stats_tlv()
in order send correct value of bt_coex status for
ROAM_SCAN_DONE logging.
Change-Id: I45ee27e5b8a52b79954dceb9f3cdc46870b7a48d
CRs-Fixed: 3236401
Add infra to support Dedicated Bluetooth Antenna Mode (DBAM)
feature. It is used to switch between dedicated antenna for
BT and shared antenna for WLAN and BT.
Change-Id: I21688093674ef9b63ee811df9168a31bd71c56b5
CRs-Fixed: 3239895
Currently the channel state of HST secondary_cur_chan_list/cur_chan_list
is out of sync and beacon IE is populated from secondary_cur_chan_list,
which causes the actual supported channel lists and country IE channel
lists are unmatched for non-6 GHz case. So let secondary_cur_chan_list
align with cur_chan_list.
Change-Id: Ie3914ac48dc05d61ac2deb78a2892986efe238dd
CRs-Fixed: 3239390
In case of RCAC, check if CAC is completed only on the RCAC
channel and do not check the CAC info on current operating
channel.
After RCAC complete is sent to FW, the RCAC tree info is
cleared. In case of RCAC, check the CAC done info only
on RCAC channel.
CRs-Fixed: 3231140
Change-Id: I976b2b5e29ebdf2dc4fb2e5df1f2feb700c972af
