This mode is supported through hw_mode_id 7. A special mode for
IPQ8074 platform alone to bring up single pdev alone on 2G mode.
FW would advertise the mode 7 support through the WMI service
ready message and this mode will be the default mode for AP-HK10 alone.
Added a function to update the svc_id mappings for this mode as FW
requires WMI commands to be received through CE 7 for this mode.
Also adjusted the preferred mode precedence to give high precedence
to mode 7.
Change-Id: Id637c59e9528779e38737b7d74b000abf2e9db9d
Currently the driver allows roaming to the BSSID
which it is already connected, which can lead to
many unexpected behaviour, for eg. if the SAP
to which the DUT is connected turns off, then the
DUT would try to roam to other BSSID of the same
SSID, and in case the SAP turns on back in time,
then the DUT would re-associate to the same BSSID.
Now if the subnet may change, and since the DHCP
does not happen again in roaming, it would then
lead to NUD failure.
Fix is to introduce an ini to allow/disallow
roaming to the same BSSID.
Change-Id: I38887bbfb74c4856a06956591be4159734f7fbf0
CRs-Fixed: 2650346
Changes to support Beacon protection. Additional key ix 6 and 7
support BIGTK. Update beacon template for Beacon protection support.
CRs-Fixed: 2632290
Change-Id: Ic37d17f5076bb28d2e1f2430da039cc8b9f759b6
Remove redundant data structure at wmi for vdev delete
response extraction, instead use mlme host data structure.
Change-Id: Iedb4280fb47d6567bc4d7b663ecd6af5e769ddfc
CRs-Fixed: 2641197
This will allow dbglog_cmd in non-tlv path
Since the fw_header structure "struct dbglog_config_msg_s" variable
"cfgvalid" increased size by one
Change-Id: I0ea9782895083b88250e9187e95456f57fa948b9
CRs-Fixed: 2626544
Remove redundant data structure at wmi for vdev delete all peer
response extraction, instead use mlme host data structure.
Change-Id: Ice91f55e0bf8a23ea1a639a74f6a8ac3b2779a7b
CRs-Fixed: 2641261
Currently QDF_MAX_NUM_CHAN and NUM_CHANNELS aren't aligned, this unalignment
may cause many potential OOB access. So replace QDF_MAX_NUM_CHAN with
NUM_CHANNELS to keep unified.
Change-Id: I7bf7829d776f7caf5b2afbd2c9fd0c20d608e630
CRs-Fixed: 2644073
Remove redundant data structure at wmi for vdev start
response extraction, instead use mlme host data structure.
Change-Id: Ie0d3e6fa0acb1fea8bc0f50095491dbe803f6810
CRs-Fixed: 2641085
The FW has updated the wmi command wmi_vdev_adfs_ch_cfg_cmd_fixed_param to
configure the Agile channel to enable the 165MHz channel as an Agile
channel by enabling 2 center frequencies.
For a 160MHz and 80MHz channel, the parameter center_freq1 will be the
center of the respective channels. For the 165MHz channel(restricted 80p80)
the parameter center_freq1 will be the center of the left 80MHz channel
(5690MHz) and the parameter center_freq2 will be the center of the right
80MHz channel (5775MHz)..
Update the ADFS parameters across UMAC, TARGET_IF and WMI layes to
update the Agile channel configuration command.
Change-Id: Ie480af9a6bb8dad87dd783ab06e17b449605b1c9
CRs-Fixed: 2642555
Add support for WMI event to host to process
dynamically selected Muedca values and update
the mgmt frames with the new set of values.
Extract the params and store in Muedca_param
struct from control path, to be used for
updating mgmt frames.
Change-Id: I6cc7756d1a246ff994edef195f6191d280bc5c47
Send new flag WMI_ROAM_OFFLOAD_FLAG_SAE_SAME_PMKID through
11i offload param to indicate fw whether WLAN_SAE_SINGLE_PMK
feature is enable or not.
If flag is set, fw should use single PMKID for SAE roaming
between VSIE AP(s), else fw should complete roaming by
doing full SAE authentication.
Change-Id: I9c88772c9571230c38e2cfa41c8a0c79663572ab
CRs-Fixed: 2616046
Add support for the following NAN messages in kmsg:-
1. NAN enable status
2. NAN, NDP match events
3. NDP channel info.
etc.
Change-Id: I7f67b67153904b7efe8a708e3f93d069e399395c
CRs-Fixed: 2618433
For restricted 80+80 MHz FR, target team initially added
wmi_service_bw_165mhz_support to indicate the target is capable of
supporting restricted 80+80 MHz.
Later, they have added wmi_service_bw_restricted_80p80_support to indicate
the same. Therefore rename wmi_service_bw_165mhz_support as
wmi_service_bw_restricted_80p80_support.
Change-Id: I12229b5d35911d4c34e63902c09592187d902bed
CRs-Fixed: 2621249
Firmware advertises WMI_SERVICE_ROAM_SCAN_CHANNEL_LIST_TO_HOST_SUPPORT
at the time of initialization, that means host can querry for roam scan
channels list to firmware.
Host driver sends WMI_ROAM_GET_SCAN_CHANNEL_LIST_CMDID to firmware to
querry roam scan channels list and firmware responds with an event
WMI_ROAM_SCAN_CHANNEL_LIST_EVENTID.
Change-Id: I419a0206d7b06b6186d0c333c951bca5206f342f
CRs-Fixed: 2620607
This patch adds the function to extract and parse the wmi events
WMI_VDEV_AUDIO_SYNC_START_STOP_EVENTID and
WMI_VDEV_AUDIO_SYNC_Q_MASTER_SLAVE_OFFSET_EVENTID. These events are
required for ftm time sync feature.
Change-Id: Ib17da82b7a8abfcff5d18125a0ba0e5249d6bf54
CRs-Fixed: 2615452
A service bit is added to indicate Firmware supports sending NSS ratio
information to Host and Host receives the NSS ratio information from
Firmware as part of service ready ext event. Save this service bit in
soc's extcap feature bit. Extract the NSS ratio info from service ready
ext event and save the results in wlan_psoc_host_mac_phy_caps structure
to calculate NSS value.
Change-Id: I8fbee48d872b0724bbb629ad38b3c959736a3c39
CRs-Fixed: 2612959
Firmware advertises service capability bit
WMI_SERVICE_PEER_DELETE_NO_PEER_FLUSH_TIDS_CMD
when peer delete command takes care of flush
all tids functionality.
If this service bit is set advertised by FW
then host does not need to send the flush tid
command before sending the peer delete command.
Change-Id: Ic6632772eeebc7f1494f1dd5e9d533b2bc22e533
CRs-Fixed: 2609962
Update value of new ini for separate iface support for NAN
"nan_separate_iface_support" to fw through a command
WMI_INIT_CMDID.
Change-Id: I55830e0d16d86ee5a0bfa7d3e44c6309c0d3d54b
CRs-Fixed: 2612010
Currently, the driver rejects the roam stats event if any of the
roam trigger or roam scan or roam results tlv is not present.
Now the firmware will send neighbor report immediately after the
neighbor report response is received from AP instead of buffering
it as done before.
So do not parse the roam trigger, roam scan, roam result tlv if
the tlv is not present. Add new flag in the tlv parsing structure
if the TLV is not present.
Change-Id: I366d8853f7f45dcdac6d4aa5c3a8a12a8b602a4f
CRs-Fixed: 2610377
As part of new requirement WLAN subsystem needs to perform thermal
mitigation action as per the thermal state of the device. The
wifi hal sends vendor command QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD
with the thermal level parameter and wlan host performs the required
appropriate action. wlan host driver maps the thermal level to
corresponding duty cycle off percent value and duty cycle value,
send WMI_THERM_THROT_SET_CONF_CMDID cmd to FW.
Make changes to perform vendor command handling, mapping thermal level
to duty cycle value and communicating the thermal information to FW.
Change-Id: I5b455ae6483f3d5bf2fe708f40c32a55eb8b9bdb
CRs-Fixed: 2610404
Add support to fallback the PMKID generation from firmware to
wpa_supplicant.
Firmware fallbacks PMKID generation to host when FIPS enabled
due to the crypto library availability limitation.
Once the roam candidate selection is done in the firmware, it
sends the WMI_ROAM_PMKID_REQUEST_EVENTID. Once this event is
received, the host driver triggers an event to wpa_supplicant
for PMKID generation.
Change-Id: Ica00d27ce3f9f4a8f966261b38e238c389fcf05c
CRs-Fixed: 2507617
Avoid direct fw headers usage in init_deinit component since
can have functional impacts. The inclusion is done at wmi level
to fix the inconsistency of code.
Change-Id: I73cc1aac500cec041de81750b9c7654d21344e6c
CRs-Fixed: 2505399
For Genoa, the WLAN FW enables IPA by default, if the
IPA is disabled by kernel config, the IPA status is
not same between wlanhost driver and WLAN FW. So add
such info in the first WMI command to let WLAN FW knows
the IPA state from host, and do the according copy engine
initialization, otherwise, the mismatch IPA copy engine
configuration will casue the Genoa FW assert.
Change-Id: Iec2f86ffb40b296c51bee41adc0d895beb200e5c
Firmware advertises service capability bit NAN_VDEV_SUPPORT for
separate NAN vdev creation. This capability can be used to create
separate interface for NAN discovery and process corresponding
commands from userspace.
Change-Id: I4f81b354433c34e8bfe264f69e4eeaf6670f2fac
CRs-Fixed: 2592016
CFR config is passed on to FW through WMI
CFR feature code is moved into feature specific WMI file.
Change-Id: I00b57ea2ef4ec5520eb565910ac2c0a6478170e3
CRs-Fixed: 2582846
Add peer assoc parameter for 6GHz Band Capabilities information
for the corresponding FW peer assoc parameter.
Change-Id: I3bc4361e449843cf73db8426d3bd97dbcd9903ed
Add wmi resource flag to send packet capture from host
to FW. Register Offload Event Id for packet capture mode.
Change-Id: Icd9e542a517c8b267a228324b7612ddded28f182
CRs-Fixed: 2528439
Currently use of comamnd QCA_NL80211_VENDOR_SUBCMD_OEM_DATA
is to pass data blobs from Application to FW but there is
no mechanism to send the data blobs from FW to Application.
To meet the above requirement update the usage of existing
OEM DATA command to use it as a vendor event as well to
send data blob from host to Application.
Change-Id: I8df98f850f4dd56f55dba43c5364a52c425ba9ed
CRs-Fixed: 2573468
After every roam happens or when neighbor report is sent by the
firmware, it sends the WMI_ROAM_STATS_EVENTID to host.
Add support to handle WMI_ROAM_STATS_EVENTID event from target
after every roam.
Change-Id: I4474135ac64ebfb17109d503fbd1c3d637457a73
CRs-Fixed: 2576258
