qcacld-3.0: Remove "sample" WCNSS_qcom_cfg.ini

Currently the qcacld-3.0 project contains a "sample" version of the
WCNSS_qcom_cfg.ini configuration file.  This differs from the "real"
versions that are kept on a per-product basis in product-specific
projects.  This has become a source of confusion since developers are
surprised when their modifications to the sample aren't reflected on
the product.  Remove the confusion by removing the sample file.  Folks
will then know they need to modify the product-specific files in their
product-specific projects.

Change-Id: Ia1b04ac431d3ae0e91d597bdfa6b8acfcd19d9e7
CRs-Fixed: 1065266

config/WCNSS_qcom_cfg.ini

@@ -1,641 +0,0 @@
-# This file allows user to override the factory
-
-# defaults for the WLAN Driver
-
-
-# Enable IMPS or not
-gEnableImps=1
-
-# Enable/Disable Idle Scan
-
-gEnableIdleScan=0
-
-
-# Increase sleep duration (seconds) during IMPS
-# 0 implies no periodic wake up from IMPS. Periodic wakeup is
-# unnecessary if Idle Scan is disabled.
-gImpsModSleepTime=0
-
-
-# Enable BMPS or not
-gEnableBmps=1
-
-# Enable suspend or not
-
-# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
-
-gEnableSuspend=3
-
-
-# Phy Mode (auto, b, g, n, etc)
-# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
-# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
-# 7 = 11b only 8 = 11ac only.
-gDot11Mode=0
-
-
-# CSR Roaming Enable(1) Disable(0)
-
-gRoamingTime=0
-
-
-# Assigned MAC Addresses - This will be used until NV items are in place
-
-# Each byte of MAC address is represented in Hex format as XX
-
-Intf0MacAddress=000AF58989FF
-Intf1MacAddress=000AF58989FE
-Intf2MacAddress=000AF58989FD
-
-Intf3MacAddress=000AF58989FC
-
-
-# UAPSD service interval for VO,VI, BE, BK traffic
-
-InfraUapsdVoSrvIntv=0
-
-InfraUapsdViSrvIntv=0
-
-InfraUapsdBeSrvIntv=0
-
-InfraUapsdBkSrvIntv=0
-
-# Flag to allow STA send AddTspec even when ACM is Off
-gAddTSWhenACMIsOff=1
-
-# Make 1x1 the default antenna configuration
-
-gNumRxAnt=1
-
-
-# Enable WAPI or not
-
-# WAPIIsEnabled=0
-
-
-# Flags to filter Mcast abd Bcast RX packets.
-
-# Value 0: No filtering, 1: Filter all Multicast.
-
-# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
-
-McastBcastFilter=3
-
-
-#Flag to enable HostARPOffload feature or not
-
-hostArpOffload=1
-
-#Flag to enable HostNSOffload feature or not
-
-hostNSOffload=1
-
-# This flag enables IP, TCP and UDP checksum offload
-gEnableIpTcpUdpChecksumOffload=1
-
-#SoftAP Related Parameters
-
-# AP MAc addr
-
-gAPMacAddr=000AF589dcab
-
-
-# 802.11n Protection flag
-
-gEnableApProt=1
-
-
-#Enable OBSS protection
-
-gEnableApOBSSProt=1
-
-
-#Enable/Disable UAPSD for SoftAP
-
-gEnableApUapsd=1
-
-
-# Fixed Rate
-
-gFixedRate=0
-
-
-# Maximum Tx power
-
-# gTxPowerCap=30
-
-
-# Fragmentation Threshold
-
-# gFragmentationThreshold=2346
-
-
-# RTS threshold
-
-RTSThreshold=1048576
-
-
-# Intra-BSS forward
-
-gDisableIntraBssFwd=0
-
-
-# WMM Enable/Disable
-
-WmmIsEnabled=0
-
-
-# 802.11d support
-
-g11dSupportEnabled=0
-
-# 802.11h support
-
-g11hSupportEnabled=1
-
-# DFS Master Capability
-gEnableDFSMasterCap=1
-
-# ESE Support and fast transition
-EseEnabled=1
-ImplicitQosIsEnabled=0
-gNeighborScanTimerPeriod=200
-
-gNeighborLookupThreshold=76
-gNeighborReassocThreshold=81
-
-gNeighborScanChannelMinTime=20
-gNeighborScanChannelMaxTime=30
-gMaxNeighborReqTries=3
-
-# Legacy (non-ESE, non-802.11r) Fast Roaming Support
-# To enable, set FastRoamEnabled=1
-# To disable, set FastRoamEnabled=0
-FastRoamEnabled=1
-
-#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
-#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
-#the RSSI of the new/roamable AP should be for roaming
-RoamRssiDiff=3
-
-# If the RSSI of any available candidate is better than currently associated
-# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
-# registering for reassoc threshold).
-# NOTE: Value of 0 means that we would register for reassoc threshold.
-gImmediateRoamRssiDiff=10
-
-# To enable, set gRoamIntraBand=1 (Roaming within band)
-# To disable, set gRoamIntraBand=0 (Roaming across band)
-gRoamIntraBand=0
-
-#Short Guard Interval Enable/disable
-
-gShortGI20Mhz=1
-
-gShortGI40Mhz=1
-
-
-#Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
-
-gAPAutoShutOff=0
-
-#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
-gWlanAutoShutdown = 0
-
-# Not used.
-gApAutoChannelSelection=0
-
-
-# Listen Energy Detect Mode Configuration
-
-# Valid values 0-128
-
-# 128 means disable Energy Detect feature
-
-# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
-
-# 10-128 are reserved.
-
-# The EDET threshold mapping is as follows in 3dB step:
-
-# 0 = -60 dBm
-
-# 1 = -63 dBm
-
-# 2 = -66 dBm
-
-# ...
-
-# 7 = -81 dBm
-
-# 8 = -84 dBm
-
-# 9 = -87 dBm
-
-# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
-
-#
-
-#  Range Loss  (dB)  =  EDET threshold level (dBm) + 97 dBm.
-
-#
-
-gEnablePhyAgcListenMode=128
-
-
-#Preferred band (both or 2.4 only or 5 only)
-
-BandCapability=0
-
-
-#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
-
-enableBeaconEarlyTermination=0
-
-beaconEarlyTerminationWakeInterval=3
-
-
-#Channel Bonding
-gChannelBondingMode5GHz=1
-
-
-#Enable Keep alive with non-zero period value
-
-gStaKeepAlivePeriod = 30
-
-#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
-#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
-#For both active and power save clients.
-
-#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
-#If doesn't honor for 5 seconds then DUT remove client.
-
-#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
-#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
-#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
-
-#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
-#where we send NULL frame.
-
-#gApLinkMonitorPeriod = 10
-
-#gGoLinkMonitorPeriod = 10
-
-#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
-#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
-
-
-gGoKeepAlivePeriod = 20
-
-gApKeepAlivePeriod = 20
-
-
-#If set will start with active scan after driver load, otherwise will start with
-
-#passive scan to find out the domain
-
-gEnableBypass11d=1
-
-
-#If set to 0, will not scan DFS channels
-
-gEnableDFSChnlScan=1
-
-# Enable DFS channel roam
-# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
-gAllowDFSChannelRoam=1
-
-gVhtChannelWidth=2
-
-# Enable Automatic Tx Power control
-
-gEnableAutomaticTxPowerControl=1
-
-# 0 for OLPC 1 for CLPC and SCPC
-gEnableCloseLoop=1
-
-#Data Inactivity Timeout when in powersave (in ms)
-gDataInactivityTimeout=200
-
-# VHT Tx/Rx MCS values
-# Valid values are 0,1,2. If commented out, the default value is 0.
-# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
-gVhtRxMCS=2
-gVhtTxMCS=2
-
-# VHT Tx/Rx MCS values for 2x2
-# Valid values are 0,1,2. If commented out, the default value is 0.
-# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
-gEnable2x2=1
-gVhtRxMCS2x2=2
-gVhtTxMCS2x2=2
-
-# NSS cfg bit definition.
-# STA          BIT[0:1]
-# SAP          BIT[2:3]
-# P2P_GO       BIT[4:5]
-# P2P_CLIENT   BIT[6:7]
-# IBSS         BIT[8:9]
-# TDLS         BIT[10:11]
-# P2P_DEVICE   BIT[12:13]
-# OCB          BIT[14:15]
-# Valid values are 1 or 2 for each two bit configuration.
-# if 2-bit value is set to 1 then the corresponidng vdev comes up in 1x1 mode
-# in the band, if set to 2 then that vdev comes up in 2x2 mode in that band.
-gVdevTypeNss_2g=43690
-gVdevTypeNss_5g=43690
-
-# Set txchainmask and rxchainmask
-# These parameters are used only if gEnable2x2 is 0
-# Valid values are 1,2
-# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
-# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
-gSetTxChainmask1x1=1
-gSetRxChainmask1x1=1
-
-# Scan Timing Parameters
-# gPassiveMaxChannelTime=110
-# gPassiveMinChannelTime=60
-gActiveMaxChannelTime=40
-gActiveMinChannelTime=20
-
-#If set to 0, MCC is not allowed.
-gEnableMCCMode=1
-
-# MCC to SCC Switch mode:
-# 0-Disable
-# 1-Enable
-# 2-Force SCC if same band, with SAP restart
-# 3-Force SCC if same band, without SAP restart by sending (E)CSA
-# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
-#   without SAP restart by sending (E)CSA
-gWlanMccToSccSwitchMode = 0
-
-# 1=enable STBC; 0=disable STBC
-gEnableRXSTBC=1
-
-# 1=enable tx STBC; 0=disable
-gEnableTXSTBC=1
-
-# 1=enable rx LDPC; 0=disable
-gEnableRXLDPC=0
-
-#Enable/Disable Tx beamforming
-gTxBFEnable=1
-
-#Enable/Disable Tx beamformee in SAP mode
-gEnableTxBFeeSAP=1
-
-# Enable Tx beamforming in VHT20MHz
-# Valid values are 0,1. If commented out, the default value is 0.
-# 0=disable, 1=enable
-gEnableTxBFin20MHz=1
-
-#Enable/Disable SU Tx beamformer support.
-gEnableTxSUBeamformer=1
-
-#Enable Scan Results Aging based on timer
-#Timer value is in seconds
-#If Set to 0 it will not enable the feature
-gScanAgingTime=30
-
-#Enable Scan Results Aging based on number of scans
-gScanResultAgeCount=1
-
-#Enable Power saving mechanism Based on Android Framework
-#If set to 0 Driver internally control the Power saving mechanism
-#If set to 1 Android Framwrok control the Power saving mechanism
-isAndroidPsEn=0
-
-#Enable thermal mitigation
-gThermalMitigationEnable=0
-
-gEnableFastRoamInConcurrency=1
-
-#Maxium Channel time in msec
-gMaxMediumTime = 6000
-
-# 802.11K support
-gRrmEnable=1
-gRrmOperChanMax=8
-gRrmNonOperChanMax=8
-gRrmRandIntvl=100
-
-#Scan offload
-gEnableDirectedScanOffload=1
-
-#FlexConnect Power Factor
-#Default is set to 0 (disable)
-gFlexConnectPowerFactor=0
-
-#Disable split scan, the FW will take care of it
-gNumChanCombinedConc=60
-
-#Enable Power Save offload
-gEnablePowerSaveOffload=2
-
-#Enable firmware uart print
-gEnablefwprint=0
-
-#P2P Listen offload
-gEnableP2pListenOffload=1
-
-# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k)
-gVhtAmpduLenExponent=7
-
-# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets)
-gVhtMpduLen=2
-
-# Maximum number of wow filters required
-#gMaxWoWFilters=22
-
-# WOW Enable/Disable.
-# 0 - Disable both magic pattern match and pattern byte match.
-# 1 - Enable magic pattern match on all interfaces.
-# 2 - Enable pattern byte match on all interfaces.
-# 3 - Enable both magic patter and pattern byte match on all interfaces.
-# Default value of gEnableWoW is 3.
-# gEnableWoW=0
-
-# Enable or Disable MCC Adaptive Scheduler at the FW
-# 1=Enable (default), 0=Disable
-gEnableMCCAdaptiveScheduler=1
-
-#Enable or Disable p2p device address administered
-isP2pDeviceAddrAdministrated=0
-
-# Remove Overlap channel restriction
-gEnableOverLapCh=0
-
-#Enable VHT on 2.4Ghz
-gEnableVhtFor24GHzBand=1
-
-#Enable or Disable 5G early beacon termination
-gEnable5gEBT=1
-
-#Maximum number of offload peers supported
-# gMaxOffloadPeers=2
-
-# controlling the following offload patterns
-# through ini parameter. Default value is 1
-# to disable set it to zero. ssdp = 0
-# Setup multicast pattern for mDNS 224.0.0.251,
-# SSDP 239.255.255.250 and LLMNR 224.0.0.252
-ssdp = 0
-
-#Enable Memory Deep Sleep
-gEnableMemDeepSleep=1
-
-# Regulatory Setting; 0=STRICT; 1=CUSTOM
-gRegulatoryChangeCountry=1
-# RA filtering rate limit param, the current value would not
-# help if the lifetime in RA is less than 3*60=3min. Then
-# we need to change it, though it is uncommon.
-# gRAFilterEnable=0
-gRArateLimitInterval=600
-
-# Maximum number of concurrent connections
-gMaxConcurrentActiveSessions=3
-
-# Disable/Enable GreenAP
-# 0 to disable, 1 to enable, default: 1
-gEnableGreenAp=1
-
-# Radar PRI multiplier
-gDFSradarMappingPriMultiplier=4
-
-gPNOScanSupport=1
-
-# Enable/Disable RX full reorder offload
-gReorderOffloadSupported=1
-
-#Enable/Disable LPASS support
-# 0 to disable, 1 to enable
-gEnableLpassSupport=0
-
-# Whether userspace country code setting shld have priority
-gCountryCodePriority=1
-
-# Enable(1)/Disable(0) SIFS burst
-gEnableSifsBurst=1
-
-# Enable or Disable Multi-user MIMO
-# 1=Enable (default), 0=Disable
-gEnableMuBformee=1
-
-# Enable/Disable channel avoidance for SAP in SCC scenario
-# 0 - disable
-# 1 - enable
-gSapSccChanAvoidance=0
-
-# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
-gIbssTxSpEndInactivityTime=10
-
-# Enable support for TDLS
-#  0 - disable
-#  1 - enable
-gEnableTDLSSupport=1
-
-# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
-# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
-# and RSSI) is met and then will initiate teardown when teardown criteria
-# (idle packet count and RSSI) is met.
-#  0 - disable
-#  1 - enable
-gEnableTDLSImplicitTrigger=1
-
-# Enable TDLS External Control. That is, user space application has to
-# first configure a peer MAC in wlan driver towards which TDLS is desired.
-# Device will establish TDLS only towards those configured peers whenever
-# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
-# when teardown criteria (idle packet count and RSSI) is met. However,
-# device will accept TDLS connection if it is initiated from any other peer,
-# even if that peer is not configured.
-#  0 - disable
-#  1 - enable
-# For TDLS External Control, Implicit Trigger must also be enabled.
-gTDLSExternalControl=1
-
-# Enable support for TDLS off-channel operation
-#  0 - disable
-#  1 - enable
-# TDLS off-channel operation will be invoked when there is only one
-# TDLS connection.
-gEnableTDLSOffChannel=1
-
-# Enable or Disable Random MAC (Spoofing)
-# 1=Enable, 0=Disable (default)
-gEnableMacAddrSpoof=0
-
-################ Datapath feature set Begin ################
-# Bus bandwidth threshold values in terms of number of packets
-gBusBandwidthHighThreshold=2000
-gBusBandwidthMediumThreshold=500
-gBusBandwidthLowThreshold=150
-
-# Bus bandwidth compute timeout value in ms
-gBusBandwidthComputeInterval=100
-
-# VHT Tx/Rx MCS values
-# Valid values are 0,1,2. If commented out, the default value is 0.
-# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
-gVhtRxMCS=2
-gVhtTxMCS=2
-
-# VHT Tx/Rx MCS values for 2x2
-# Valid values are 0,1,2. If commented out, the default value is 0.
-# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
-gEnable2x2=1
-gVhtRxMCS2x2=2
-gVhtTxMCS2x2=2
-
-#IPA config
-gIPAConfig=0
-gIPADescSize=800
-gIPAPreFilterEnable=1
-gIPARMEnable=1
-gIPAIPv6Enable=1
-
-IpaUcOffloadEnabled=0
-gIpaUcStaOffload=0
-
-# Enable/Disable RX full reorder offload
-gReorderOffloadSupported=1
-
-# Enable CE classification
-# 1 - enable(default)  0 - disable
-gCEClassifyEnable=1
-
-# Enable Rx handling options
-# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
-rx_mode=4
-
-# Enable(Tx) fastpath for data traffic.
-# 1 - enable(default)  0 - disable
-gEnableFastPath=1
-
-# This flag enables IP, TCP and UDP checksum offload
-# 1 - enable(default)  0 - disable
-gEnableIpTcpUdpChecksumOffload=1
-
-# Enable TCP Segmentation Offload
-# 1 - enable(default)  0 - disable
-TSOEnable=1
-
-# Enable Large Recieve Offload
-# 1 - enable(default)  0 - disable
-LROEnable=1
-################ Datapath feature set End ################
-
-################ NAN feature set start ###################
-
-# Enable NAN discovery (NAN 1.0)
-# 1 - enable(default)  0 - disable
-gEnableNanSupport=1
-
-################ NAN feature set end #####################
-
-END
-
-# Note: Configuration parser would not read anything past the END marker
-