diff --git a/config/WCNSS_qcom_cfg.ini b/config/WCNSS_qcom_cfg.ini deleted file mode 100644 index 7541563b42..0000000000 --- a/config/WCNSS_qcom_cfg.ini +++ /dev/null @@ -1,641 +0,0 @@ -# This file allows user to override the factory - -# defaults for the WLAN Driver - - -# Enable IMPS or not -gEnableImps=1 - -# Enable/Disable Idle Scan - -gEnableIdleScan=0 - - -# Increase sleep duration (seconds) during IMPS -# 0 implies no periodic wake up from IMPS. Periodic wakeup is -# unnecessary if Idle Scan is disabled. -gImpsModSleepTime=0 - - -# Enable BMPS or not -gEnableBmps=1 - -# Enable suspend or not - -# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter - -gEnableSuspend=3 - - -# Phy Mode (auto, b, g, n, etc) -# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac -# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only -# 7 = 11b only 8 = 11ac only. -gDot11Mode=0 - - -# CSR Roaming Enable(1) Disable(0) - -gRoamingTime=0 - - -# Assigned MAC Addresses - This will be used until NV items are in place - -# Each byte of MAC address is represented in Hex format as XX - -Intf0MacAddress=000AF58989FF -Intf1MacAddress=000AF58989FE -Intf2MacAddress=000AF58989FD - -Intf3MacAddress=000AF58989FC - - -# UAPSD service interval for VO,VI, BE, BK traffic - -InfraUapsdVoSrvIntv=0 - -InfraUapsdViSrvIntv=0 - -InfraUapsdBeSrvIntv=0 - -InfraUapsdBkSrvIntv=0 - -# Flag to allow STA send AddTspec even when ACM is Off -gAddTSWhenACMIsOff=1 - -# Make 1x1 the default antenna configuration - -gNumRxAnt=1 - - -# Enable WAPI or not - -# WAPIIsEnabled=0 - - -# Flags to filter Mcast abd Bcast RX packets. - -# Value 0: No filtering, 1: Filter all Multicast. - -# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast - -McastBcastFilter=3 - - -#Flag to enable HostARPOffload feature or not - -hostArpOffload=1 - -#Flag to enable HostNSOffload feature or not - -hostNSOffload=1 - -# This flag enables IP, TCP and UDP checksum offload -gEnableIpTcpUdpChecksumOffload=1 - -#SoftAP Related Parameters - -# AP MAc addr - -gAPMacAddr=000AF589dcab - - -# 802.11n Protection flag - -gEnableApProt=1 - - -#Enable OBSS protection - -gEnableApOBSSProt=1 - - -#Enable/Disable UAPSD for SoftAP - -gEnableApUapsd=1 - - -# Fixed Rate - -gFixedRate=0 - - -# Maximum Tx power - -# gTxPowerCap=30 - - -# Fragmentation Threshold - -# gFragmentationThreshold=2346 - - -# RTS threshold - -RTSThreshold=1048576 - - -# Intra-BSS forward - -gDisableIntraBssFwd=0 - - -# WMM Enable/Disable - -WmmIsEnabled=0 - - -# 802.11d support - -g11dSupportEnabled=0 - -# 802.11h support - -g11hSupportEnabled=1 - -# DFS Master Capability -gEnableDFSMasterCap=1 - -# ESE Support and fast transition -EseEnabled=1 -ImplicitQosIsEnabled=0 -gNeighborScanTimerPeriod=200 - -gNeighborLookupThreshold=76 -gNeighborReassocThreshold=81 - -gNeighborScanChannelMinTime=20 -gNeighborScanChannelMaxTime=30 -gMaxNeighborReqTries=3 - -# Legacy (non-ESE, non-802.11r) Fast Roaming Support -# To enable, set FastRoamEnabled=1 -# To disable, set FastRoamEnabled=0 -FastRoamEnabled=1 - -#Check if the AP to which we are roaming is better than current AP in terms of RSSI. -#Checking is disabled if set to Zero.Otherwise it will use this value as to how better -#the RSSI of the new/roamable AP should be for roaming -RoamRssiDiff=3 - -# If the RSSI of any available candidate is better than currently associated -# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without -# registering for reassoc threshold). -# NOTE: Value of 0 means that we would register for reassoc threshold. -gImmediateRoamRssiDiff=10 - -# To enable, set gRoamIntraBand=1 (Roaming within band) -# To disable, set gRoamIntraBand=0 (Roaming across band) -gRoamIntraBand=0 - -#Short Guard Interval Enable/disable - -gShortGI20Mhz=1 - -gShortGI40Mhz=1 - - -#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled - -gAPAutoShutOff=0 - -#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec -gWlanAutoShutdown = 0 - -# Not used. -gApAutoChannelSelection=0 - - -# Listen Energy Detect Mode Configuration - -# Valid values 0-128 - -# 128 means disable Energy Detect feature - -# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. - -# 10-128 are reserved. - -# The EDET threshold mapping is as follows in 3dB step: - -# 0 = -60 dBm - -# 1 = -63 dBm - -# 2 = -66 dBm - -# ... - -# 7 = -81 dBm - -# 8 = -84 dBm - -# 9 = -87 dBm - -# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: - -# - -# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. - -# - -gEnablePhyAgcListenMode=128 - - -#Preferred band (both or 2.4 only or 5 only) - -BandCapability=0 - - -#Beacon Early Termination (1 = enable the BET feature, 0 = disable) - -enableBeaconEarlyTermination=0 - -beaconEarlyTerminationWakeInterval=3 - - -#Channel Bonding -gChannelBondingMode5GHz=1 - - -#Enable Keep alive with non-zero period value - -gStaKeepAlivePeriod = 30 - -#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). -#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) -#For both active and power save clients. - -#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. -#If doesn't honor for 5 seconds then DUT remove client. - -#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on -#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. -#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. - -#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period -#where we send NULL frame. - -#gApLinkMonitorPeriod = 10 - -#gGoLinkMonitorPeriod = 10 - -#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. -#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. - - -gGoKeepAlivePeriod = 20 - -gApKeepAlivePeriod = 20 - - -#If set will start with active scan after driver load, otherwise will start with - -#passive scan to find out the domain - -gEnableBypass11d=1 - - -#If set to 0, will not scan DFS channels - -gEnableDFSChnlScan=1 - -# Enable DFS channel roam -# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE -gAllowDFSChannelRoam=1 - -gVhtChannelWidth=2 - -# Enable Automatic Tx Power control - -gEnableAutomaticTxPowerControl=1 - -# 0 for OLPC 1 for CLPC and SCPC -gEnableCloseLoop=1 - -#Data Inactivity Timeout when in powersave (in ms) -gDataInactivityTimeout=200 - -# VHT Tx/Rx MCS values -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gVhtRxMCS=2 -gVhtTxMCS=2 - -# VHT Tx/Rx MCS values for 2x2 -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gEnable2x2=1 -gVhtRxMCS2x2=2 -gVhtTxMCS2x2=2 - -# NSS cfg bit definition. -# STA BIT[0:1] -# SAP BIT[2:3] -# P2P_GO BIT[4:5] -# P2P_CLIENT BIT[6:7] -# IBSS BIT[8:9] -# TDLS BIT[10:11] -# P2P_DEVICE BIT[12:13] -# OCB BIT[14:15] -# Valid values are 1 or 2 for each two bit configuration. -# if 2-bit value is set to 1 then the corresponidng vdev comes up in 1x1 mode -# in the band, if set to 2 then that vdev comes up in 2x2 mode in that band. -gVdevTypeNss_2g=43690 -gVdevTypeNss_5g=43690 - -# Set txchainmask and rxchainmask -# These parameters are used only if gEnable2x2 is 0 -# Valid values are 1,2 -# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. -# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. -gSetTxChainmask1x1=1 -gSetRxChainmask1x1=1 - -# Scan Timing Parameters -# gPassiveMaxChannelTime=110 -# gPassiveMinChannelTime=60 -gActiveMaxChannelTime=40 -gActiveMinChannelTime=20 - -#If set to 0, MCC is not allowed. -gEnableMCCMode=1 - -# MCC to SCC Switch mode: -# 0-Disable -# 1-Enable -# 2-Force SCC if same band, with SAP restart -# 3-Force SCC if same band, without SAP restart by sending (E)CSA -# 4-Force SCC if same band (or) use SAP mandatory channel for DBS, -# without SAP restart by sending (E)CSA -gWlanMccToSccSwitchMode = 0 - -# 1=enable STBC; 0=disable STBC -gEnableRXSTBC=1 - -# 1=enable tx STBC; 0=disable -gEnableTXSTBC=1 - -# 1=enable rx LDPC; 0=disable -gEnableRXLDPC=0 - -#Enable/Disable Tx beamforming -gTxBFEnable=1 - -#Enable/Disable Tx beamformee in SAP mode -gEnableTxBFeeSAP=1 - -# Enable Tx beamforming in VHT20MHz -# Valid values are 0,1. If commented out, the default value is 0. -# 0=disable, 1=enable -gEnableTxBFin20MHz=1 - -#Enable/Disable SU Tx beamformer support. -gEnableTxSUBeamformer=1 - -#Enable Scan Results Aging based on timer -#Timer value is in seconds -#If Set to 0 it will not enable the feature -gScanAgingTime=30 - -#Enable Scan Results Aging based on number of scans -gScanResultAgeCount=1 - -#Enable Power saving mechanism Based on Android Framework -#If set to 0 Driver internally control the Power saving mechanism -#If set to 1 Android Framwrok control the Power saving mechanism -isAndroidPsEn=0 - -#Enable thermal mitigation -gThermalMitigationEnable=0 - -gEnableFastRoamInConcurrency=1 - -#Maxium Channel time in msec -gMaxMediumTime = 6000 - -# 802.11K support -gRrmEnable=1 -gRrmOperChanMax=8 -gRrmNonOperChanMax=8 -gRrmRandIntvl=100 - -#Scan offload -gEnableDirectedScanOffload=1 - -#FlexConnect Power Factor -#Default is set to 0 (disable) -gFlexConnectPowerFactor=0 - -#Disable split scan, the FW will take care of it -gNumChanCombinedConc=60 - -#Enable Power Save offload -gEnablePowerSaveOffload=2 - -#Enable firmware uart print -gEnablefwprint=0 - -#P2P Listen offload -gEnableP2pListenOffload=1 - -# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) -gVhtAmpduLenExponent=7 - -# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) -gVhtMpduLen=2 - -# Maximum number of wow filters required -#gMaxWoWFilters=22 - -# WOW Enable/Disable. -# 0 - Disable both magic pattern match and pattern byte match. -# 1 - Enable magic pattern match on all interfaces. -# 2 - Enable pattern byte match on all interfaces. -# 3 - Enable both magic patter and pattern byte match on all interfaces. -# Default value of gEnableWoW is 3. -# gEnableWoW=0 - -# Enable or Disable MCC Adaptive Scheduler at the FW -# 1=Enable (default), 0=Disable -gEnableMCCAdaptiveScheduler=1 - -#Enable or Disable p2p device address administered -isP2pDeviceAddrAdministrated=0 - -# Remove Overlap channel restriction -gEnableOverLapCh=0 - -#Enable VHT on 2.4Ghz -gEnableVhtFor24GHzBand=1 - -#Enable or Disable 5G early beacon termination -gEnable5gEBT=1 - -#Maximum number of offload peers supported -# gMaxOffloadPeers=2 - -# controlling the following offload patterns -# through ini parameter. Default value is 1 -# to disable set it to zero. ssdp = 0 -# Setup multicast pattern for mDNS 224.0.0.251, -# SSDP 239.255.255.250 and LLMNR 224.0.0.252 -ssdp = 0 - -#Enable Memory Deep Sleep -gEnableMemDeepSleep=1 - -# Regulatory Setting; 0=STRICT; 1=CUSTOM -gRegulatoryChangeCountry=1 -# RA filtering rate limit param, the current value would not -# help if the lifetime in RA is less than 3*60=3min. Then -# we need to change it, though it is uncommon. -# gRAFilterEnable=0 -gRArateLimitInterval=600 - -# Maximum number of concurrent connections -gMaxConcurrentActiveSessions=3 - -# Disable/Enable GreenAP -# 0 to disable, 1 to enable, default: 1 -gEnableGreenAp=1 - -# Radar PRI multiplier -gDFSradarMappingPriMultiplier=4 - -gPNOScanSupport=1 - -# Enable/Disable RX full reorder offload -gReorderOffloadSupported=1 - -#Enable/Disable LPASS support -# 0 to disable, 1 to enable -gEnableLpassSupport=0 - -# Whether userspace country code setting shld have priority -gCountryCodePriority=1 - -# Enable(1)/Disable(0) SIFS burst -gEnableSifsBurst=1 - -# Enable or Disable Multi-user MIMO -# 1=Enable (default), 0=Disable -gEnableMuBformee=1 - -# Enable/Disable channel avoidance for SAP in SCC scenario -# 0 - disable -# 1 - enable -gSapSccChanAvoidance=0 - -# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode -gIbssTxSpEndInactivityTime=10 - -# Enable support for TDLS -# 0 - disable -# 1 - enable -gEnableTDLSSupport=1 - -# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall -# initiate TDLS Discovery towards a peer whenever setup criteria (throughput -# and RSSI) is met and then will initiate teardown when teardown criteria -# (idle packet count and RSSI) is met. -# 0 - disable -# 1 - enable -gEnableTDLSImplicitTrigger=1 - -# Enable TDLS External Control. That is, user space application has to -# first configure a peer MAC in wlan driver towards which TDLS is desired. -# Device will establish TDLS only towards those configured peers whenever -# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS -# when teardown criteria (idle packet count and RSSI) is met. However, -# device will accept TDLS connection if it is initiated from any other peer, -# even if that peer is not configured. -# 0 - disable -# 1 - enable -# For TDLS External Control, Implicit Trigger must also be enabled. -gTDLSExternalControl=1 - -# Enable support for TDLS off-channel operation -# 0 - disable -# 1 - enable -# TDLS off-channel operation will be invoked when there is only one -# TDLS connection. -gEnableTDLSOffChannel=1 - -# Enable or Disable Random MAC (Spoofing) -# 1=Enable, 0=Disable (default) -gEnableMacAddrSpoof=0 - -################ Datapath feature set Begin ################ -# Bus bandwidth threshold values in terms of number of packets -gBusBandwidthHighThreshold=2000 -gBusBandwidthMediumThreshold=500 -gBusBandwidthLowThreshold=150 - -# Bus bandwidth compute timeout value in ms -gBusBandwidthComputeInterval=100 - -# VHT Tx/Rx MCS values -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gVhtRxMCS=2 -gVhtTxMCS=2 - -# VHT Tx/Rx MCS values for 2x2 -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gEnable2x2=1 -gVhtRxMCS2x2=2 -gVhtTxMCS2x2=2 - -#IPA config -gIPAConfig=0 -gIPADescSize=800 -gIPAPreFilterEnable=1 -gIPARMEnable=1 -gIPAIPv6Enable=1 - -IpaUcOffloadEnabled=0 -gIpaUcStaOffload=0 - -# Enable/Disable RX full reorder offload -gReorderOffloadSupported=1 - -# Enable CE classification -# 1 - enable(default) 0 - disable -gCEClassifyEnable=1 - -# Enable Rx handling options -# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium) -rx_mode=4 - -# Enable(Tx) fastpath for data traffic. -# 1 - enable(default) 0 - disable -gEnableFastPath=1 - -# This flag enables IP, TCP and UDP checksum offload -# 1 - enable(default) 0 - disable -gEnableIpTcpUdpChecksumOffload=1 - -# Enable TCP Segmentation Offload -# 1 - enable(default) 0 - disable -TSOEnable=1 - -# Enable Large Recieve Offload -# 1 - enable(default) 0 - disable -LROEnable=1 -################ Datapath feature set End ################ - -################ NAN feature set start ################### - -# Enable NAN discovery (NAN 1.0) -# 1 - enable(default) 0 - disable -gEnableNanSupport=1 - -################ NAN feature set end ##################### - -END - -# Note: Configuration parser would not read anything past the END marker -