fw-api: CL 4101399 - update fw common interface files

Change-Id: Ide6bab3d541dbf42d239db0e06117d27a4ab04b2
WMI: dynamically negotiate max_nlo_ssids value
CRs-Fixed: 1107600

fw/wmi_unified.h

@@ -2211,6 +2211,15 @@ typedef struct {
      * bits 31:28 -> CRM sub ID
      */
     A_UINT32 fw_build_vers_ext;
+    /* max_nlo_ssids - dynamically negotiated maximum number of SSIDS for NLO
+     * This limit is the maximum number of SSIDs that can be configured in the
+     * target for Network List Offload (i.e. scanning for a preferred network).
+     * If this value is 0x0, the target supports WMI_NLO_MAX_SSIDS (16).
+     * If this value is non-zero, the host should send back in the
+     * WMI_INIT message's wmi_resource_config.max_nlo_ssids a value that
+     * is equal to or less than the target capability limit reported here.
+     */
+    A_UINT32 max_nlo_ssids;
 } wmi_service_ready_ext_event_fixed_param;
 
 typedef enum {
@@ -2726,6 +2735,27 @@ typedef struct {
 
     /* Max no of STA with which TWT sessions can be formed by the AP */
     A_UINT32 twt_ap_sta_count;
+
+    /* max_nlo_ssids - dynamically negotiated maximum number of SSIDS for NLO
+     * This parameter provides the final specification for the maximum number
+     * of SSIDs for the target to support for Network List Offload's scanning
+     * for preferred networks.
+     * This wmi_resource_config.max_nlo_ssids must be <= the max_nlo_ssids
+     * field from the target's WMI_SERVICE_READY_EXT_EVENT message.
+     * (If the target didn't provide a max_nlo_ssids field in the
+     * WMI_SERVICE_READY_EXT message, or if the SERVICE_READY_EXT msg's
+     * max_nlo_ssids value was 0x0, the target doesn't support dynamic
+     * negotiation of max NLO SSIDs, and WMI_NLO_MAX_SSIDS (=16) applies.)
+     * If this wmi_resource_config.max_nlo_ssids field is absent or 0x0,
+     * the host does not support dynamic negotiation of max NLO SSIDs.
+     * In such a case, the target will respond as follows:
+     * If the target supports at least WMI_NLO_MAX_SSIDS, the target will
+     * use the statically-configured WMI_NLO_MAX_SSIDS value.
+     * If the target supports less than WMI_NLO_MAX_SSIDS, the target will
+     * abort its boot-up, due to receiving an invalid/unsupported
+     * configuration specification.
+     */
+    A_UINT32 max_nlo_ssids;
 } wmi_resource_config;
 
 #define WMI_RSRC_CFG_FLAG_SET(word32, flag, value) \

fw/wmi_version.h

@@ -36,7 +36,7 @@
 #define __WMI_VER_MINOR_    0
 /** WMI revision number has to be incremented when there is a
  *  change that may or may not break compatibility. */
-#define __WMI_REVISION_ 498
+#define __WMI_REVISION_ 499
 
 /** The Version Namespace should not be normally changed. Only
  *  host and firmware of the same WMI namespace will work