123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152 |
- ########################### Start of libnf-hal-st_aosp.conf ###########################
- ###############################################################################
- ###############################################################################
- # ST HAL trace log level
- STNFC_HAL_LOGLEVEL=4
- NFC_DEBUG_ENABLED=1
- ###############################################################################
- # Vendor specific mode to enable FW (RF & SWP) traces.
- STNFC_FW_DEBUG_ENABLED=0
- ###############################################################################
- # File used for NFA storage
- NFA_STORAGE="/data/nfc"
- ###############################################################################
- # Dev Node used for ST HAL
- ST_NFC_DEV_NODE="/dev/st_no_such_device"
- ###############################################################################
- # Keep the nfa storage file.
- PRESERVE_STORAGE=1
- ###############################################################################
- # In Switch OFF mode (phone switched-off), specify the desired CE mode to
- # the controller.
- # 0: No card-emulation; DEFAULT
- # 1: Switch-off card-emulation enabled
- CE_ON_SWITCH_OFF_STATE=1
- ###############################################################################
- # Vendor specific mode to support the USB charging mode if VPSIO=1 in switch off.
- STNFC_USB_CHARGING_MODE=1
- ###############################################################################
- # Vendor Specific Proprietary Protocol & Discovery Configuration
- # Set to 0xFF if unsupported
- # byte[0] NCI_PROTOCOL_18092_ACTIVE
- # byte[1] NCI_PROTOCOL_B_PRIME
- # byte[2] NCI_PROTOCOL_DUAL
- # byte[3] NCI_PROTOCOL_15693
- # byte[4] NCI_PROTOCOL_KOVIO
- # byte[5] NCI_PROTOCOL_MIFARE
- # byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
- # byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
- # byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
- NFA_PROPRIETARY_CFG={05:FF:FF:06:8A:90:77:FF:FF}
- ###############################################################################
- # Choose the presence-check algorithm for type-4 tag. If not defined,
- # the default value is 1.
- # 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
- # 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
- # 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate
- # 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0
- # 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3
- # 5 NFA_RW_PRES_CHK_ISO_DEP_NAK; presence check command ISO-DEP NAK as per NCI2.0
- PRESENCE_CHECK_ALGORITHM=5
- ###############################################################################
- # Name of the NCI HAL module to use
- # If unset, falls back to nfc_nci.bcm2079x
- NCI_HAL_MODULE="nfc_nci.st21nfc"
- ###############################################################################
- # White list to be set at startup.
- DEVICE_HOST_WHITE_LIST={02:C0}
- ###############################################################################
- # BAIL OUT value for P2P
- # Implements algorithm for NFC-DEP protocol priority over ISO-DEP protocol.
- POLL_BAIL_OUT_MODE=1
- ###############################################################################
- # Extended APDU length for ISO_DEP
- ISO_DEP_MAX_TRANSCEIVE=0xFEFF
- ###############################################################################
- # Configure the NFC Extras to open and use a static pipe. If the value is
- # not set or set to 0, then the default is use a dynamic pipe based on a
- # destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value
- # for each EE (ESE/SIM)
- OFF_HOST_ESE_PIPE_ID=0x5E
- OFF_HOST_SIM_PIPE_ID=0x3E
- ###############################################################################
- #Set the default Felica T3T System Code OffHost route Location :
- #This settings will be used when application does not set this parameter
- # host 0x00
- # eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
- # UICC 0x81 (UICC_1), 0x85 (UICC_2)
- DEFAULT_SYS_CODE_ROUTE=0x86
- ###############################################################################
- #Set the Felica T3T System Code supported power state:
- DEFAULT_SYS_CODE_PWR_STATE=0x3B
- ###############################################################################
- # Path and Files used for FW update binaries storage
- STNFC_FW_PATH_STORAGE="/vendor/firmware"
- STNFC_FW_BIN_NAME="/st54j_fw.bin"
- STNFC_FW_CONF_NAME="/st54j_conf.bin"
- ###############################################################################
- # Default off-host route for Felica.
- # This settings will be used when application does not set this parameter
- # host 0x00
- # eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
- # UICC 0x81 (UICC_1), 0x85 (UICC_2)
- DEFAULT_NFCF_ROUTE=0x86
- ###############################################################################
- # Configure the default off-host route.
- # used for technology A and B routing
- # eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
- # UICC 0x81 (UICC_1), 0x85 (UICC_2)
- DEFAULT_OFFHOST_ROUTE=0x81
- ###############################################################################
- # Configure the default AID route.
- # host 0x00
- # eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
- # UICC 0x81 (UICC_1), 0x85 (UICC_2)
- DEFAULT_ROUTE=0x00
- ###############################################################################
- # Configure the NFCEEIDs of offhost UICC.
- # UICC 0x81 (UICC_1), 0x85 (UICC_2)
- OFFHOST_ROUTE_UICC={81}
- ###############################################################################
- # Configure the NFCEEIDs of offhost eSEs.
- # eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
- OFFHOST_ROUTE_ESE={86}
- ###############################################################################
- # Configure the list of NFCEE for the ISO-DEP routing.
- # host 0x00
- # eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
- # UICC 0x81 (UICC_1), 0x85 (UICC_2)
- DEFAULT_ISODEP_ROUTE=0x81
- ###############################################################################
- # Core configuration settings
- CORE_CONF_PROP={ 20, 02, 0a, 03,
- a1, 01, 1e,
- a2, 01, 19,
- 80, 01, 01
- }
|