########################### Start of libnf-hal-st_aosp.conf ###########################

###############################################################################
###############################################################################
# ST HAL trace log level
STNFC_HAL_LOGLEVEL=1
NFC_DEBUG_ENABLED=0

###############################################################################
# Vendor specific mode to enable FW (RF & SWP) traces.
STNFC_FW_DEBUG_ENABLED=0

###############################################################################
# File used for NFA storage
NFA_STORAGE="/data/nfc"

###############################################################################
# Keep the nfa storage file.
PRESERVE_STORAGE=1

###############################################################################
# In Switch OFF mode (phone switched-off), specify the desired CE mode to
# the controller.
# 0: No card-emulation; DEFAULT
# 1: Switch-off card-emulation enabled
CE_ON_SWITCH_OFF_STATE=1

###############################################################################
# Vendor specific mode to support the USB charging mode if VPSIO=1 in switch off.
STNFC_USB_CHARGING_MODE=1

###############################################################################
# Vendor Specific Proprietary Protocol & Discovery Configuration
# Set to 0xFF if unsupported
#  byte[0] NCI_PROTOCOL_18092_ACTIVE
#  byte[1] NCI_PROTOCOL_B_PRIME
#  byte[2] NCI_PROTOCOL_DUAL
#  byte[3] NCI_PROTOCOL_15693
#  byte[4] NCI_PROTOCOL_KOVIO
#  byte[5] NCI_PROTOCOL_MIFARE
#  byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
#  byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
#  byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
NFA_PROPRIETARY_CFG={05:FF:FF:06:8A:90:77:FF:FF}

###############################################################################
# Choose the presence-check algorithm for type-4 tag.  If not defined,
# the default value is 1.
# 0  NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
# 1  NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
# 2  NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate
# 3  NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0
# 4  NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3
# 5  NFA_RW_PRES_CHK_ISO_DEP_NAK; presence check command ISO-DEP NAK as per NCI2.0
PRESENCE_CHECK_ALGORITHM=5

###############################################################################
# Name of the NCI HAL module to use
# If unset, falls back to nfc_nci.bcm2079x
NCI_HAL_MODULE="nfc_nci.st21nfc"

###############################################################################
# ALLOW list to be set at startup.
DEVICE_HOST_ALLOW_LIST={02:C0}

###############################################################################
# BAIL OUT value for P2P
# Implements algorithm for NFC-DEP protocol priority over ISO-DEP protocol.
POLL_BAIL_OUT_MODE=1

###############################################################################
# Extended APDU length for ISO_DEP
ISO_DEP_MAX_TRANSCEIVE=0xFEFF

###############################################################################
# Configure the NFC Extras to open and use a static pipe.  If the value is
# not set or set to 0, then the default is use a dynamic pipe based on a
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE).  Note there is a value
# for each EE (ESE/SIM)
OFF_HOST_ESE_PIPE_ID=0x5E
OFF_HOST_SIM_PIPE_ID=0x3E

###############################################################################
#Set the default Felica T3T System Code OffHost route Location :
#This settings will be used when application does not set this parameter
# host  0x00
# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
# UICC  0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_SYS_CODE_ROUTE=0x86

###############################################################################
#Set the Felica T3T System Code supported power state:
DEFAULT_SYS_CODE_PWR_STATE=0x3B

###############################################################################
# Path and Files used for FW update binaries storage
STNFC_FW_PATH_STORAGE="/vendor/firmware"
STNFC_FW_BIN_NAME="/st54j_fw.bin"
STNFC_FW_CONF_NAME="/st54j_conf.bin"

###############################################################################
# Default off-host route for Felica.
# This settings will be used when application does not set this parameter
# host  0x00
# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
# UICC  0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_NFCF_ROUTE=0x86

###############################################################################
# Configure the default off-host route.
# used for technology A and B routing
# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
# UICC  0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_OFFHOST_ROUTE=0x81

###############################################################################
# Configure the default AID route.
# host  0x00
# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
# UICC  0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_ROUTE=0x00

###############################################################################
# Configure the NFCEEIDs of offhost UICC.
# UICC  0x81 (UICC_1), 0x85 (UICC_2)
OFFHOST_ROUTE_UICC={81}

###############################################################################
# Configure the NFCEEIDs of offhost eSEs.
# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
OFFHOST_ROUTE_ESE={86}

###############################################################################
# Configure the list of NFCEE for the ISO-DEP routing.
# host  0x00
# eSE   0x82 (eSE),    0x86 (eUICC/SPI-SE)
# UICC  0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_ISODEP_ROUTE=0x81

###############################################################################
# Configure the HAL Clock control
# enable  0x01
# disable 0x00 default value
STNFC_CONTROL_CLK=0x01

###############################################################################
# Configure the ACTIVE_RW timer
# Default 0x00, set 0x01 to enable it
STNFC_ACTIVERW_TIMER=0x01

###############################################################################
# Core configuration settings
CORE_CONF_PROP={ 20, 02, 0a, 03,
        a1, 01, 1e,
        a2, 01, 19,
        80, 01, 01
}